olympia electronics GR-290/WP/M User manual

Page 1 from 6 923293004_09_004
GENERAL
o
This device is used indoors (ta 40 C) in
places where emergency luminaires are
needed. Each device must be permanently
connected to mains power supply. The
l u m i n a i r e s G R - 2 9 0 / W P / M a n d G R -
292/WP/M are suitable for corridors lighting
and the GR-291/WP/M and GR-293/WP/M
for open area lighting. In normal operation
the battery is charging. In case of a mains
power supply failure, the device enters
emergency mode and the illumination LED
turns on. When the mains power supply is
restored t h e dev i c e tur n s t o no r m a l
operation.
INSTALLATION
To install the luminaire follow the installation
instructions οn page 3.
Battery Charging
The battery charging is completely
controlled. In this case, is achieved the
perfect battery maintenance , as well as the
elongation of its duration. When the battery
has completely charged, it charges with a
maintenance current.
Battery Cut-off
The device in this operation when the mains
power supply fails and battery has lost its
energy. During this operation the device
enters the idle state and battery consumption
is negligible, in order to be protected from
deep discharge.
Automatic Operational Test
It is conducted automatically every 15 days. In
order to be performed, the mains power
supply and the battery should be connected.
Automatic Autonomous Test
The Automatic Autonomous Test is conducted
and measures the device’s back up operation
and emergency duration. The BATTERY
FAULT LED blinks during the measurement,
indicating this process to the user. This test is
conducted automatically every six months. In
order to be performed, the mains power
supply and the battery should be connected
and fully charged. If the battery is not fully
charged, the test is postponed until the
battery is completely charged. If during this
test, the autonomy is less than the nominal
then the battery fault led turned on
continuously and the battery must be
WATERPROOF SELF TESTING NON-MAINTAINED EMERGENCY CEILING MOUNTED LUMINAIRES
OPERATION VOLTAGE
MAXIMUM POWER CONSUMPTION
BATTERY (NiMh)
220-240V AC / 50-60Hz
4.8V/1.2Ah
4.3W / 4.7 VA
TECHNICAL CHARACTERISTICS (for LED MODULE specifications see page 5)
Thank you for your trust in our products
Olympia Electronics - European manufacturer
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
CONSTRUCTION MATERIAL
EXTERNAL DIMENSION
WEIGHT
GUARANTEE
CHARGE TIME
INDICATIONS - CONTROLS
BATTERY PROTECTION
MINIMUM DURATION
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
EMERGENCY ILLUMINATION
LIGHT SOURCE
1.5 hour
24 hours
Deep discharge and overcharge protection
IP65
300lm
1 white power LED
o
5 to 40 C
Up to 95%
ABS/PC
3 years (1 year for the battery)
442gr.
Ø125 x 65 mm
EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3
Charge, lamp fault, battery fault
3 hours
150lm
GR-290/WP/M GR-291/WP/M GR-292/WP/M GR-293/WP/M
INSULATION BETWEEN SUPPLY & CONTROL TERMINALS
Basic insulation

replaced.
Back Up Operation
The autonomous duration of battery during
emergency mode is at least the one that is
stated in the list of the technical
characteristics. During emergency mode, a
light source test is also performed.
ΑΤΤΕΝΤΙΟΝ!!!
1. Operations for installation, maintainance or
testing must be done by authorized personnel
only.
2. The device must be connected to the
m a i n s p o w e r s u p p l y t h r o u g h a f u s e
dependent by the total amount of the line’s
power load.
3. The replacement of the battery and the light
source must be done using parts of the same
type, by the manufacturer or by a competent
person.
4. In case of inactive use for a period greater
than 2 months, disconnect the battery by
pulling out the battery’s connector.
5. I s n ot al low ed to dis ca rd t i
batteries into common trash bins,
they must be discarded only in
battery recycling points. Do not
incinerate.
Connection to module (After request)
This luminaire can be connected to any of the
following modules: Remote module, address
module, wireless module and fault relay
module. If you connect it to a module that
supports inhibit or rest mode, you should
know that these commands can be cancelled
only during normal mode (ie. not in
emergency). For installation refer to step 3 of
the istallation procedure in page 3.
Also refer to the user’s manual of each
module for additional information.
NOTE: LED= Light Emitting Diode
LABELING EXPLANATION:
X: Self contained
0: Non maintained (*)
A: Including test device
B: Including remote test mode
C: Including inhibiting mode
F: Automatic test gear complying with IEC
61347-2-7 denoted EL-T
90: 1.5 hour duration
180: 3 hour duration
Maintained operation: The luminaire lights its
illumination source, when it is powered by the
mains power supply or not.
(*) Non Maintained operation: The luminaire
turns on illumination source, only in case of
Page 2 from 6
Status of LEDs
LEDs Description of indication
CHARGE : Battery charging, : battery charged, : disconnected or unfunctional battery
LAMP FAULT : Operation check, : lamp fault, : normal operation
BATT. FAULT : Autonomy test, : battery fault, : normal operation
Note : Blinking, : constantly on, : off
Note!! If a module will be used (except the fault
relay module), then the installer should fill in, on
the specification label, the letters B and C.
X09 0A F
923293004_09_004

Page 3 from 6
INSTALLATION INSTRUCTIONS
3
2
1 Untighten the screw but do not remove it and pull up the reflector.
2 Always use in any case round mains cable, with a diameter of 5-10mm (H05RN-F type 2x1mm²
or any other type, at least equal to it’s mechanical and electrical properties). ATTENTION!!
The cable must not be deformed in any way (This requirement is important to ensure the ΙΡ
rating). Install the included gaskets in to the cable entry holes (verify that are not deformed). Make a
hole in the center by using a small screwdriver. Pass the round cable through the gasket. Detach the
power terminal, connect the wires as shown in the picture and attach the power terminal (10A max). If
you use a module pass the 2 signal cables on the A, B terminals Minding the correct polarity.
Depending on the module that will be used, the cables that will be used, have different names. In A,
signal +L, C are also connected, while signals -L, NC/NO in the terminal B.
3 Place the battery’s connector to the corresponding connector on the P.C.B.
4 Refit the reflector (mind the correct orientation), tighten the screw securely and the luminaire is
ready for mounting.
NOTE!! After finishing the installation you must power the luminaire for at least 24 hours in
order to completely charge the battery. The rated autonomy duration can be achieved after that
time.
Battery replacement.
It can be done only by a competent person and after the mains interruption.
1. Remove the luminaire from the suspended ceiling (figure 3).
2. Follow the step 1 of the installation instructions.
3. Disconnect the connector and remove the old battery.
4. Connect the new battery with the same type (step 2 of the installation instructions) and place it in
the position of the old one.
5. Replace the removed parts (step 1 and 4) and power the device.
Important notice for the installed luminaires in one area !!!
The installer must connect the battery’s connector first and then should power the luminaire.
The time between batteries connection must be, at least 1.5 minute.
With this variation, it is ensured that the non synchronized Automatic Autonomous Test for two or more
luminaires installed in one area, is not conducted in the same day.
11
Cable
entry
hole
923293004_09_004

MOUNTING THE LAMP IN SUSPENDED CEILING
Set up the lamp to the suspended ceiling as it is shown bellow (Required opening 110mm):
Step 1
Bend the springs, to get into the hole of the suspended ceiling, as you can see to the next figure.
Step 2
Push up the luminaire, as shown in figure 2.
Step 3
Continue to push upwards until the lamp locks.
If you want to pull off the device, put a flat blade
screwdriver, between the device and the ceiling.
Figure 2
Figure 3
Figure 1
Ø110mm
Page 4 from 6
SURFACE MOUNTING
Step 1. Follow the step 1 of the installation instructions.
Step 2. Unfasten the retaining screw (Figure 4) and detach the part for suspended ceiling installation.
Step 3. Drill 2 holes on the base using a 4mm drill bit in order to permit the retaining screws to pass. Mark
these two drilled points on the required mounting location, drill the holes and install the supplied
plastic plugs. ATTENTION!! Especially for the GR-290/WP/M and GR-292/WP/M luminaire
installation on the ceiling you must align the base with the indications on the luminaire’s base
(Figure 5).
Step 4. WARNING!! To preserve the ΙΡ 65 rating, fit the screws with the metallic washer and plastic
ring which are included. Next use the screw to fasten the unit to the surface .(Figure 6)
Step 5. Install the decorative rim (package included). Next, use the 2 fasteners to install the unit to the
require location.
Step 6. Follow the step3 of the installation instructions.
Figure 6Figure 4 Figure 5
Drill here
Indications
Retaining fastener
923293004_09_004

Page 5 from 6
LED MODULE CHARACTERISTICS
Olympia Electronics S.A.
6 °0 C max. across the board
3-3,2V DC
1,3W
0405185
fixed connection between main pcb and led module
Manufacturer
Model Number
Voltage Range
Connections
Nominal Power
Temperature (tc)
Lamp fault
indication LED
ATTENTION!!!
During installation follow this light direction.
Corridor
lighting
Open
area
lighting
FAULT
LAMP
CHARGE
BATT.
FAULT
LAMP
CHARGE
BATT.
96
65
125
FAULT
LAMP
CHARGE
BATT.
Battery
fault
indication
LED
Battery
charge
indication
LED
Figure 4
The light source contained in this luminaire shall only be replaced by the manufacturer, or his
agent, or a similar qualified person.
NOTE! The light source is non-user replaceable.
CAUTION : Do not view directly with bare eyes.
FAULT
LAMP
CHARGE
BATT.
GR-290/WP/M GR-291/WP/M GR-292/WP/M GR-293/WP/M
GR-290/WP/M, GR-292/WP/M
GR-291/WP/M, GR-293/WP/M
923293004_09_004

Page 6 from 6
WARRANTY
Olympia Electronics guarantees the quality, condition and operation of the goods. The period of warranty
is specified in the official catalogue of Olympia Electronics and also in the technical leaflet, which
accompanies each product. This warranty ceases to exist if the buyer does not follow the technical
instructions included in official documents given by Olympia Electronics or if the buyer modifies the goods
provided or has any repairs or re-setting done by a third party, unless Olympia Electronics has fully
agreed to them in writing. Products that have been damaged can be returned to the premises of our
company for repair or replacement, as long as the warranty period is valid.
Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge the
buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or not the
buyer the transportation cost.
HEAD OFFICE
72nd km. O.N.R. Thessaloniki-Katerini
P.C. 60300 P.O. Box 06 Εginio Pierias Greece
www.olympia-electronics.gr
[email protected]
923293004_09_004