olympia electronics GR-108/12L/90 User manual

‘’CLASSIC LIGHT‘’ SERIES FOR NON MAINTAINED / ΜΑΙΝΤΑΙΝΕD
EMERGENCY LUMINAIRES
GR-109/12L/180
GR-108/12L/90
220-240V AC/50-60Hz
3 hours90 min
24 h
Battery charging LED, TEST button
From overcharge and deep discharge
IP20
3.6V/600mAh 3.6V/1Ah
40lm / 100lm 38lm / 100lm
12 white LED’s
3W / 3.5VA2.5W / 3VA
EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3
5 to 40 C
o
Up to 95%
ABS/PC, PC
3 years (1 year for the battery)
262 x 100 x 69 mm
Page 1 of 3
GENERAL
o
These luminaires are used indoors (ta 40 C)
where emergency light is needed.
Each luminaire must be permanently connected
to mains power supply.
In normal operation the battery is charging and
the 2 yellow LED’s light in the screen.
In case of a mains power supply failure the
luminaire will light the led strip automatically in
emergency mode. When the mains power
supply is restored the device turns to normal
operation.
MAINTAINED / NON-MAINTAINED
OPERATION
There is an option to select the maintained or
non-maintained operation by placing the jumper
to the appropriate place according to step 4
(page 2).
ΑΤΤΕΝΤΙΟΝ!!!
1. Operations for installation, maintainance or
testing must be done by authorized personnel
only.
2. The device must be connected to the mains
power supply through a fuse dependent by the
total amount of the line’s power load.
3. It is suggested to check every month the
indication LED for battery charging, and by
pushing the TEST button to check the emergency
circuit. The led strip should: a) light with bigger
intensity as long as the TEST button is pressed
(maintained operation),
b) light as long as the TEST button is pressed
(non-maintained operation).
4. It is suggested to check every 6 months the
minimum autononous duration by disconnecting
the mains power supply. Count the time that the
led strip lights and in case of less time than the
minimum autonomous duration the battery must
be replaced. If the measured time is considerably
less than the minimum autonomous duration
In case of battery or led strip
replacement, these must be replaced by parts of
the same type, by the manufacturer or by a
competent person.
t i
in battery recycling
points.
Do not incinerate.
If the luminaire
doesn’t work as described above contact the
installer.
contact the installer.
5. In case of inactive use for a period greater than
2 months, disconnect the battery by pulling out
the battery’s connector.
6. I s not allowed to discard batteries into
common trash bins, they must be
discarded only
535gr 545gr
923109004_09_010
Thank you for your trust in our products
Olympia Electronics - European manufacturer
TECHNICAL CHARACTERISTICS (for LED MODULE Spec ifications see page 2)
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
EXTERNAL DIMENSIONS
CONSTRUCTION MATERIALS
TYPICAL WEIGHT
GUARANTEE
OPERATION VOLTAGE
MAXIMUM POWER CONSUMPTION
BATTERIES (Ni-Cd)
CHARGING TIME
INDICATIONS - CONTROLS
BATTERY PROTECTION
MINIMUM AUTONOMOUS DURATION
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
EMERGENCY ILLUMINATION
ILLUMINATION SOURCE

INSTALLATION INSTRUCTIONS
Page 2 of 3
1. Detach the plastic base (located in the bottom of the luminaire) by pulling the unlock hook and
pass the cables from area or and through the cable entry hole. The luminaire must be
connected to a permanent electrical installation to ensure the immobilization of the cable. Mount
the plastic base with the included mounting accessories.
2. Connect the mains cables to the respective detachable
terminal block. Ν for neutral, L for live wire.
3. Attach the luminaire by sliding it on the plastic base until the
plastic hook locks, and power the luminaire.
4. MAINTAINED/NON-MAINTAINED OPERATION
JUMPER SELECTION
You can choose the luminaire’s operation. When the
jumper is installed (by default) in the middle and right pins
maintained operation is selected.
When the jumper is installed in the middle and left pins non-
maintained operation is selected.
NOTE!!
After finishing the installation you must power the device at least for 24 ours for battery
charging to perform the nominal autonomy.
Maintained
operation
Non-maintained
operation
3
L230V AC
NPlastic base
1
2
Cable entry hole
N
L
A
B
N L
AB
Battery replacement
It can be done only by a competent person and after
the mains interruption.
1. Detach the luminaire from its base (step 1 of the
installation procedure).
2. Use a flat blade screwdriver to remove the diffusor.
3. Remove the reflector.
4. Disconnect the connector and remove the old battery.
5. Connect the new battery with the same type and
place it in the position of the old one.
6. Replace the removed parts (step 1,2 and 3).
2
LED MODULE CHARACTERISTICS
Olympia Electronics S.A.
Cable connection between main pcb and led module
45 °C max. across the board
2.9-3.6VDC
780mW
0111163
GR-108/12L/90
GR-109/12L/180
Lock - unlock hook
Manufacturer
Model Number
Voltage Range
Connections
Nominal Power
Temperature (tc)
923109004_09_010

Page 3 of 3
The light source contained in this luminaire shall only be replaced by the manufacturer, or his
agent, or a similar qualified person.
NOTE! The light source is non-user replaceable.
WARRANTY
Olympia Electronics guarantees the quality, condition and operation of the goods. The period of warranty
is specified in the official catalogue of Olympia Electronics and also in the technical leaflet, which
accompanies each product. This warranty ceases to exist if the buyer does not follow the technical
instructions included in official documents given by Olympia Electronics or if the buyer modifies the goods
provided or has any repairs or re-setting done by a third party, unless Olympia Electronics has fully
agreed to them in writing. Products that have been damaged can be returned to the premises of our
company for repair or replacement, as long as the warranty period is valid.
Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge the
buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or not the
buyer the transportation cost.
HEAD OFFICE
72nd km. O.N.R. Thessaloniki-Katerini
P.C. 60300 P.O. Box 06 Εginio Pierias Greece
www.olympia-electronics.gr
[email protected]
(*) Maintained operation: The luminaire lights its illumination source, when it is powered by the mains
power supply or not.
Non Maintained operation: The luminaire lights its illumination source, only in power supply’s failure.
Note!! The installer should fill in, on the
specification label, the letter G if the
luminaire is used as a safety sign.
NOTE: LED= Light Emitting Diode
LABELING EXPLANATION:
X: Self contained
1: Maintained (*)
A: Including test device
G: Internally illuminated safety sign
90: 1.5 hour duration
180: 3 hours duration
X 1 9 0A
G
923109004_09_010