olympia electronics WEATHER LIGHT Series User manual

Thank you for purchasing this product of
Olympia Electronics. A European
manufacturer.
GENERAL
These luminaires are used in places where
emergency luminaires are needed.
Each luminaire must be permanently
connected to mains power supply. In normal
operation the battery is charging and the 2
yellow LED’s light in the screen (see step 4
on page 2).In case of a mains power
supply failure the luminaire will light the
led strip automatically in emergency mode.
When the mains power supply is restored
the device turns to normal operation.
ΑΤΤΕΝΤΙΟΝ!!!
1. Operations for installation, maintainance
or testing must be done by authorized
personel only.
2. The device must be connected to the
mains power supply thru a fuse dependent
by the total amount of the line’s power load.
3. It is sugested to check every month the
indication LED for battery charging, and by
pushing the TEST button (see the paragraph
9 on page 2), to check the emergency cirquit.
The lamp should light as long as the TEST
button is pressed. In the opposite condition
contact the installer.
4. It is sugested to check every 6 months the
minimum autononous duration by
disconnecting the mains power supply. Count
the time that the led strip lights and in case of
less time than the minimum autonomous
duration the battery must be replaced. If the
measured time is considerably less than the
minimum autonomous duration
The replacement of the battery and
the light source must be done using parts of
the same type, by the manufacturer or by a
competent person.
t i
in battery recycling
points. Do not incinerate.
contact the
installer.
5. In case of inactive use for a period greater
than 2 months, disconnect the battery by
pulling out the battery’s connector.
6. I s not allowed to discard batteries in
to common trash bins, they must be
discarded only
INSTALLATION
To install the luminaire follow the installation
instructions οn page 2.
NOTE: LED= Light Emitting Diode
LABELING EXPLANATION:
X: Self contained
0: Non Maintained
A: Including test device
*90: 90min duration
180: 180min duration
‘’ WEATHER LIGHT ‘’ SERIES FOR NON-MAINTAINED EMERGENCY LUMINAIRES
Page 1 from 2 923936006_23_011
High Quality European based Manufacturers
220-240V AC/50-60Hz
Bayblent FR3010, transparent polycarbonate
TECHNICAL CHARACTERISTICS
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
EXTERNAL DIMENSIONS
CONSTRUCTION MATERIALS
TYPICAL WEIGHT
GUARANTEE
OPERATION VOLTAGE
MAXIMUM POWER CONSUMPTION
BATTERIES (Ni-Cd)
CHARGING TIME
INDICATIONS - CONTROLS
BATTERY PROTECTION
MINIMUM AUTONOMOUS DURATION
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
EMERGENCY ILLUMINATION
ILLUMINATION SOURCE 180min90min 24h
Charge indication LED, TEST button
From overcharge and full discharge
300lm 300lm450lm 415lm
4 power LED’s 4 power LED’s 6 power LED’s6 power LED’s
0 to 40 C
o
Up to 95%
3 years (1 year for the battery)
363 x 145 x 73 mm
4.8V/1.5Ah 4.8V/3Ah 4.8V/4Ah(Ni-MH)
950gr. 980gr. 1020gr.
EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3
IP 65
4,8VA 5,5VA4VA
GR-935/6P GR-936/4P GR-936/6P
GR-935/4P

Page 2 from 2
1Remove the diffusor.Place simultaneously 2 flat blade screwdrivers and pull up gently the
reflector.
2Install the included plastic cover in to the unused hole and install the base plastic (with the
included mounting screws and plugs).
3Always use in any case round mains cable,with external diameter of 6-9mm (H05RN-F type
2x1mm² or any other type,at least equal to it’s mechanical and electrical properties).
ATTENTION!! The cable must not be deformed in any way (This requirement is important to
ensure the tightness isolation IP 65). Install the cable gland,pass the round cable thru and
tighten it all the way.
4Place the battery’s connector to the corresponding connector on the P.C.B. NOTE!! If you don’t
need the yellow led’s to light in normal operation, then remove the led jumper.
5Connect the mains as shown in figure (connect the ground wire if required).
6Install the included tie (if needed) to fasten securely the power cables.
7Refit the reflector and fasten the two small screws (included).
8Finaly place the diffusor by using the 4 included screws (tightening torque 1.2Nm).
INSTALLATION INSTRUCTIONS
N
L
L N
23
6
5
Mains connection
923936006_23_011
4
LED
JUMPER
NOTE!! After finishing the installation you must power the
luminaire at least for 24 hours for battery charging to perform the
named autonomy.
8
7
1
9 Unfasten the mounting screws (step 8) and remove the diffusor.
When the luminaire is supplied by the mains, press on the marking
for TEST as shown in the picture below. Mount the diffusor by using
the 4 removed screws.
TEST procedure with extra care!!
Battery replacement.
It can be done only by a competent person and after the mains interruption.
1. Follow the step 1of the installation procedure. Unfasten the 2 retaining screws and remove the
reflector (photo step 7).
2. Disconnect the connector and remove the old battery.
3. Connect the new battery with the same type (step 4of the installation procedure) and place it
in the position of the old one.
4. Follow the step 7 and 8 of the installation procedure and power the device.