olympia electronics GR-316/15L/MAR User manual

Thank you for purchasing this product of Olympia
Electronics. A European manufacturer.
GENERAL
These luminaires are suitable for marine and
offshore applications where emergency light is
needed. Each luminaire must be permanently
connected to mains power supply.In normal
operation the led strip lights and the battery is
charging. In case of a mains power supply
failure the luminaire will light the led strip
automatically in emergency mode (powered by
its battery). When the mains power supply is
restored the device turns to normal operation.
INSTALLATION
To install the luminaire follow the installation
instructions on page 4.
Battery Charging
The battery charging is completely controlled. In
this case, the best possible battery maintenance
is achieved, as well as the elongation of its
duration. When the battery has completely
charged, it charges with a maintenance current.
Battery Cut-off
The luminaire enters in this operation when the
mains power supply fails and battery has lost its
energy. During this operation the luminaire
enters the idle state and battery consumption is
negligible, in order to be protected from deep
discharge.
Manual Test
The manual test can be conducted only if the
main power supply and the battery is connected.
By pressing the test button briefly an operation
test is initiated. During this test period all
indication LEDs are OFF.
Automatic Test
This test includes all the operations that provide
the manual test and is conducted automatically
every 15 days. In order to be performed, the
main power supply and the battery should be
connected.
Automatic Autonomous Test
The Automatic Autonomous Test is conducted
and measures the luminaire`s back up operation.
This test is conducted automatically every six
months. In order to be performed, the main
power supply and the battery should be
connected (the battery should be charged). If the
battery is not charged, the test is postponed until
the battery is completely charged. If during the
Automatic Autonomous Test the luminaire’s
duration is lower than the nominal, then the
battery must be replaced.
Back Up Operation
The autonomous duration of battery during
emergency mode is at least the one that is
stated in the technical characteristics. During
emergency mode, a LED strip test is also
performed.
Resetting Errors
Push the Test button for 5 seconds, to extinguish
all the indicated LED errors. Then the luminaire
enters regular operation mode.
Indication LED status (with connected mains
power supply).
Charge
On: Good charge current.
Οff: No battery (No charging current
or disconnected battery).
Lamp Fault with L1 connected to L
Page 1 from 4
SELF-TESTING MAINTAINED EMERGENCY LUMINAIRES WITH WHITE LED’s
GR-316/30L/MARGR-316/15L/MAR
220-240V AC/50-60Hz
5W / 8VA3.5W / 7VA
Bayblend FR3010, transparent polycarbonate
TECHNICAL CHARACTERISTICS
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
EXTERNAL DIMENSIONS
CONSTRUCTION MATERIALS
TYPICAL WEIGHT
GUARANTEE
OPERATION VOLTAGE
MAXIMUM POWER CONSUMPTION
BATTERIES (Ni-Cd)
CHARGING TIME
INDICATIONS - CONTROLS
BATTERY PROTECTION
MINIMUM AUTONOMOUS DURATION
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
ILLUMINATION (MAINS / EMERGENCY)
ILLUMINATION SOURCE 180min
24h
Charge, lamp fault, fault indication LED, TEST button
From overcharge and full discharge
IP 40
3.6V/1.5Ah 3.6V/3Ah
30 white LED’s15 white LED’s
5 to 40 C
o
Up to 95%
3 years (1 year for the battery)770gr.
350 x 134 x 45 mm (CRV 362 x 134 x 58 mm)
210lm /210lm105lm /105lm
700gr.
High Quality European based Manufacturers
923316017_09_003
EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3, IEC 60092-306, IEC 60533

Page 2 from 4
Installation methods
A-3018
Special mounting
springs for
suspended ceiling
installation
Mounting springs Α-3018
Wall or ceiling installation Suspended ceiling installation
Recess mounting
base Α-3016
Recess mounting in a wall
Οn (with LED strip off):Faulty LED strip (must
be replaced).
Οn (with LED strip on):Problem in the back up
circuit of the LED strip (must be checked by an
authorized personel).
Off: Good LED strip.
Battery Fault
Οff:Battery OK.
Blink (With Charge LED ON): Autonomy or low
battery problem (the battery must be replaced).
Blink (With Charge LED Off):
No charging current or disconnected battery.
ΑΤΤΕΝΤΙΟΝ!!!
1. Operations for installation, maintainance or
testing must be done by authorized personel
only.
2. The device must be connected to the mains
power supply through a fuse dependent by the
total amount of the line’s power load.
In case of battery or lamp replacement, these
must be replaced by parts of the same type, by
the manufacturer or by a competent person.
t i
in battery recycling
points. Do not incinerate.
3.
4. In case of inactive use for a period greater
than 2 months, disconnect the battery by pulling
out the battery’s connector.
5. I s not allowed to discard batteries in to
common trash bins, they must be
discarded only
923316017_09_003
Wall installation with SP-114
marking panel
A-3018
SP-114 marking panel
Suspended ceiling installation
with Α-3018 mounting springs
and SP-114 marking panel
Ceiling installation
with SP-114 marking panel

Page 3 from 4
Suspended ceiling
Α-3018 mounting springs
PLACING Α-CRV PARTS
To install the curve crystal Α-CRV you must first install the
included plastic extension to mount it on the TEST button.
1
2
3
Mounting methods
All “Easy Light” can be mounted either surface or recess
mounted in walls or suspended ceilings. For recess
mounted installations, special accessories are required
which can be found in the catalog and must be ordered
separately.
Suspended ceiling installation.
On the bottom of the base plastic of the Easy light
luminaire there are two Hshaped cut outs. These are
used to install the A-3018 mounting springs.
1. With a sharp tool remove the appropriate plastic
pieces to fit the mounting springs. First place the edges
of the mounting spring to the respective holes and install
the one end of the coil to the support axis.
2. Install the other end of the coil to the other support
axis.
3. Bend the springs and place the luminaire to the
respective suspended ceiling’s hole.
The luminaire’s placement to the suspended ceiling
must be done after the connection with power supply
cables.
Recess mounting in a wall
The special mounting base (A-3016) can be built in the
wall and on it can be mounted the luminaire with the Α-
3016 included screws, following the installation
instructions of the luminaire. The mounting base
contains pre-etched holes for cable entry that are
aligned with the cable entry holes of the luminaire.
Bottom view of a wall
Α-3016 recess
mounting base
Mounting Easy Light luminaire
in a suspended ceiling
Recess mounting for an ‘’Easy Light”
luminaire in a wall.
Required
opening in
a suspended
ceiling
340
124
MARKING PANEL SP-114
A marking panel SP-114 can be installed on the
luminaire in 3 different locations. This marking
panel is installed perpendicular to the diffusor of
the luminaire, as shown in the pictures below.
The panel is pre-printed and has a plastic
accessory on each side that is used to fasten the
panel to the luminaires.
There are 2 arrow stickers that can be placed in
each side of the marking panel to point to the
desired direction.
Placing the SP-114 marking panel
Place the plastic mounting accessories of the
marking panel as shown in pictures.
ΝΟΤΕ!! This marking panel (SP type) can not
be installed on CRV luminaires.
923316017_09_003

Page 4 from 4
INSTALLATION INSTRUCTIONS
Base plastic
Cable entry channels
Luminaire mounting holes
1 To install the luminaire you must dismantle it into 3 parts.
2 Place a flat blade screwdriver in the area Α to release the diffusor’s
plastic hook.
3Place a flat blade screwdriver in the area Bto release the reflector’s
plastic hook.
4 Use the included mounting parts to mount the base plastic.
Pass the mains cable through a cable entry channel. The luminaire
must be connected to a permanent electrical installation to ensure the
immobilization of the cable.
5 Place the battery’s connector to the corresponding connector on the
P.C.B.
6 Connect the mains cables to the respective detachable terminal
block. Ν for neutral, L for live wire and L1 for the maintained
operation. The L1 wire can be connected to an external switch to
control the maintained or non maintained operation of the luminaire.
For permanent maintained operation use two wires to power the
luminaire, Ν for neutral and L for live wire, and link the L and L1.
7 Refit the removed parts in steps 2 and 3 (mind the correct orientation)
and the luminaire is ready to operate.
N
N
L
L
External
switch
Link
Controled operation
of the illumination source
Permanent
operation of the illumination source
NN
L L
L1 L1
NOTE: LED= Light Emitting Diode
LABELING EXPLANATION:
X: Self contained
1: Maintained (*)
A: Including test device
180: 3 hour duration
All the types of Easy Light series, are also produced with a new designed crystal with GR-XXX/MAR/CRV code,
for example GR-316/30L/MAR/CRV.
13
Diffusor
Reflector
Base plastic B
A
B
2
A
(*) Maintained operation: The luminaire lights its illumination source, when it is powered by the mains power supply
or not.
Non Maintained operation: The luminaire lights its illumination source, only in power supply’s failure.
NOTE!!
After finishing the installation you must power the luminaire at least for 24 hours for battery charging to
perform the nominal autonomy.
45 6
N
LL1
923316017_09_003
Battery replacement.
It can be done only by a competent person and after the mains interruption.
1. Follow the step 2 and 3 of the installation procedure.
2. Disconnect the connector and remove the old battery.
3. Connect the new battery with the same type (step 5 of the installation procedure) and place it in the position
of the old one.
4. Follow the step 7 of the installation procedure and power the device.