olympia electronics SLD-28/SP User manual

Page 1 from 4922044006_09_024
SLD-34/SP SLD-44/SP SLD-28/SP
220-240V AC/50-60Hz
3h
24h
Overcharging and deep discharging protection
Charge LED, Lamp LED, Fault LED, Test Button
IP30
3.6V/1.5Ah
100lm /100lm 125lm /125lm
9.5 VA9 VA
EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3, EN 1838
5 to 40 C
o
up to 95%
Bayblend FR3010, aluminum, plexiglas
280x120x15mm
3 years (1 year for the battery)
790gr. 1110gr. 1580gr.
340x190x15mm 440x240x15mm
289x65x34mm
TECHNICAL CHARACTERISTICS (for LED MODULE specifications see page 4)
SELF TESTING MAINTAINED EMERGENCY ILLUMINATION SIGNS WITH WHITE LEDs
GENERAL
The luminaire consists mainly from two Battery Cut-off
parts, the body, where all the electronics The luminaire enters in this operation when
are located and the lamp-head where the the mains power supply fails and battery
indication sign and the high efficiency has lost its energy. During this operation
LEDs are located. the luminaire enters the idle state and
battery consumption is negligible, in order
Maintained to non-maintained selection to be protected from deep discharge.
capability
Power on the device and press Manual Test
continuously the TEST button for 10 The manual test can be conducted only if
seconds, until the led strip turns off. the mains power supply and the battery is
Release the button and after a short connected. By pressing the test button
emergency test, the device operates as briefly an operation test is initiated. During
non maintained. If you want to restore the this test period all indication LEDs are
previous condition (maintained operation), OFF.
press continuously the TEST button for 10
seconds, until the led strip lights. Release Automatic Operatioanal Test
the button and after a short emergency This test includes all the operations that
test, the device operates as maintained provide the manual test and is conducted
illumination sign. automatically every 15 days. In order to be
performed, the mains power supply and
Battery Charging the battery should be connected.
The battery charging is completely
controled. In this case, is achieved the Automatic Autonomous Test
perfect battery maintenance , as well as the The Automatic Autonomous Test is
elongation of its duration. When the battery conducted and measures the luminaire`s
has completely charged, it charges with a back up operation. This test is conducted
maintenance current. automatically every six months. In order to
Thank you for your trust in our products
Olympia Electronics - European manufacturer
Operation temperature range
Relative humidity
Construction materials
External panel's dimensions
External unit’s dimensions
Typical weight
Guarantee
Mains voltage
Maximum power consumption
Battery (Ni-MH)
Recharging time
Battery protection
Indications
Minimum emergency duration
Degrees of cover protection
Produced in accordance with
Light source intensity (230V) / (emerg.)

Page 2 from 4 922044006_09_024
be performed, the mains power supply Indication LED status (with connected
and the battery should be connected (the mains power supply).
battery should be charged). If the battery
is not charged, the test is postponed until Charge
the battery is completely charged. If On: Charge current OK.
during the Automatic Autonomous Test the Οff: No battery (No charging current or
luminaire’s duration is lower than the disconnected battery).
named, then the battery must be Lamp Fault
replaced. Οn: Faulty LED strip.
Off: LED strip OK.
Back Up Operation
The autonomous duration of battery Battery Fault
during emergency mode is at least the Οff:Battery OK.
one that is stated in the list of the first Blink (With Charge LED ON): Autonomy
page. During emergency mode, a LED or low battery problem (the battery must
strip test is also performed. be replaced).
Blink (With Charge LED Off):
Resetting Errors No charging current or disconnected
Push the Test button for 5 seconds, to battery.
delete all the indicated LED errors. Then
the luminaire enters regular operation
mode.
INSTALLATION INSTRUCTIONS
General:
1. Operations for installation, maintainance or testing must be done by authorized
personnel only.
2. The device must be connected to the mains power supply through a fuse dependent
by the total amount of the line’s power load.
In case of battery or light source replacement, these must be replaced by parts of the
same type, by the manufacturer or by a competent person.
4
t i in battery recycling points.
Do not incinerate.
3.
. In case of inactive use for a period greater than 2 months, disconnect the battery by
pulling out the battery’s connector.
5. I s not allowed to discard batteries in to common trash bins, they must be
discarded only
1
4
3
Remove the front plastic cover by unscrewing the two
retaining screws.
Pass the mains cables through the hole of the plastic base.
Connect the live and the neutral wires to the terminal block
as shown in picture.
Mount the device by installing the included mounting
accessories in the holes or use the Α-3018 mounting
springs for suspended seiling mounting.
Install LED strip and batery connectors to the appropriate
PCB connectors.
Refit the front plastic cover by srewing the two
removed screws in step 1, and power on the device.
1
2
3
4
5
6
5
2
L
N
NOTE!!
After finishing the installation you must power the device
at least for 24 hours for battery charging to perform
the nominal autonomy.

Page 3 from 4 922044006_09_024
In recess mounting installation the
required opening is 280 x 50 mm.
The material must withstand the
luminaires weight.
280
50
(*) Maintained operation: The luminaire lights its
illumination source, when it is powered by the mains power
supply or not.
Non Maintained operation: The luminaire lights its
illumination source, only in power supply’s failure.
NOTE: LED= Light Emitting Diode
LABELING EXPLANATION:
X: Self contained
1: Maintained (*)
A: Including test device
G: Internally illuminated
*180: 3hours duration
ATTENTION!!
To disconnect the panel’s cables, you have to power off the mains power supply and
disconnect the battery.
The light source contained in this luminaire shall only be replaced by the manufacturer, or his
agent, or a similar qualified person.
NOTE! The light source is non-user replaceable.
Placing the mounting springs
Α-3018
1
2
Place one part of the mounting spring
first and then the other one.
Place the edges of the mounting spring
as shown in picture.
1
2
Recess mounting
in suspended ceiling
A-3018
Mounting springs
for recess mounting
A-3018 mounting springs
Ceiling mounting Wall mounting
Mounting methods
When the device is mounted externally it can use the A-1028 mounting box.

WARRANTY
Olympia Electronics guarantees the quality, condition and operation of the goods. The period of
warranty is specified in the official catalogue of Olympia Electronics and also in the technical leaflet,
which accompanies each product. This warranty ceases to exist if the buyer does not follow the
technical instructions included in official documents given by Olympia Electronics or if the buyer
modifies the goods provided or has any repairs or re-setting done by a third party, unless Olympia
Electronics has fully agreed to them in writing. Products that have been damaged can be returned to
the premises of our company for repair or replacement, as long as the warranty period is valid.
Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge
the buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or
not the buyer the transportation cost.
HEAD OFFICE
72nd km. O.N.R. Thessaloniki-Katerini
P.C. 60300 P.O. Box 06 Eginio Pierias Greece
www.olympia-electronics.gr
[email protected]
LED MODULE CHARACTERISTICS
Olympia Electronics S.A.
45 °C max. across the board
Cable connection between main pcb and led module
8.7-10.8V DC 0.975W
2312083
0.78W
0106163 1307083
SLD-28/SP SLD-34/SP SLD-44/SP
Manufacturer
Model Number
Voltage Range
Connections
Nominal Power
Temperature (tc)
Page 4 from 4 922044006_09_024