olympia electronics GRL-21/H/90 User manual

Page 1 from 3923021042_09_005
TECHNICAL CHARACTERISTICS
220-240V AC/50-60Hz
SUPPLY CURRENT
OPERATION VOLTAGE
MAXIMUM POWER CONSUMPTION
BATTERY (DJWS12-7.0) Sealed Lead-Acid 12V/7Ah, 0 ~ 40°C 2 x Sealed Lead-Acid 12V/7Ah, 0 ~ 40°C
BATTERY PROTECTION
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
EXTERNAL DIMENSIONS
CONSTRUCTION MATERIALS
GUARANTEE
CHARGING TIME
INDICATIONS - CONTROLS
MINIMUM AUTONOMOUS DURATION
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
EMERGENCY ILLUMINATION
LIGHT SOURCE
24h
IP42
o
5 to 40 C
Up to 95%
3 years (1 year for the battery)
180 min90 min
3200lm
White LEDs
EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3
U-OUT
30V
OPEN CIRCUIT VOLTAGE 23.5V DC
75°C at R11
8A/250V FB, 5x20mm
Prated/Irated
Iemergency
WIRE CROSS SECTION
CONTROL GEAR FUSE
CONTROL GEAR MAX. TEMPERATURE
Deep discharge and overcharge protection / the control gear will recharge the battery normally after the test of 22.3
MAX. VOLTAGE IN STANDBY OPERATION
MIN. - MAX.CHARGE CURRENT / VOLTAGE RANGE
MIN. - MAX. DISCHARGE CURRENT / VOLTAGE RANGE
230 - 710 mA / 10.5 - 14.5V
1700 - 2300 mA / 13.8 - 10.5
CONTROLGEAR MIN/MAX VOLTAGE LOAD OUTPUT 17 / 23V
TYPICAL WEIGHT
MAX. CHARGING VOLTAGE IN NORMAL CYCLE
14.5V
13.8V
2
Power Cables: 0.8-2.5mm
60 °C max. across the board
Cable connection between main pcb and led module
19-23V
4.9W
2002163
Built-in
Basic Insulation
700 V
590 mA on each lamp
NON MAINTAINED EMERGENCY LUMINAIRES
GRL-21/H/90 GRL-21/H/180
13.3W/14VA
Aluminium, ABS/PC, PC
6300gr.4100gr
21.6W / 1.2A
590mA per Lamp
2.15A
Power, Battery Charge / TEST Button
63 mA
Rated CURRENT @12V
ELECTRONIC CONTROL GEAR
The controlgear can supply the LED modules only during emergency operation
The controlgear has mains-connected windings of transformer
The controlgear is suitable for LED module only
LED MODULE CHARACTERISTICS
Olympia Electronics S.A.
Manufacturer
Voltage Range
Connections
Nominal Power
Supply Current
Temperature (tc)
Model Number
Max Working Voltage for Proper Insulation
LV Supply - Control Conductors Insulation Type
LED Module Type
The controlgear is proof against supply voltage polarity reversal
The lamp controlgear relies upon the luminaire enclosure for protection against accidental contact with live part (7.2 BS EN 61347-2-7)
302 x 94 x 350 χιλ.
NOTE Maintenance of the declared insulation barrier for the luminaire can also be dependent on other external
components/products connected to the same bus. This is the responsibility of the control system designer, not
the luminaire manufacturer.

Thank you for your trust in our products
Olympia Electronics - European manufacturer
GENERAL
DIMMING OPTION
When the device is powered from the mains,
and the battery(ies) is(are) connected, the
‘power’ and ‘charge’ indicators are ON. The
‘charge’ indicator indicates the battery charging
operation. If it does not light, probably, the
batteries are disconnected. If it does not light
and the batteries are connected, then contact
the technician. The power indicator confirms the
proper connection to the mains. The TEST
button, has a dual use. If pressed instantlly while
the device is connected to the mains, the device
simulates the power interruption, by lighting the
lamps for 3''. In that way, we can control the
driver circuit of the lamps and the lamps as
indicated in paragraph 3 in the text below.
o
These luminaires are used indoors (ta 40 C) where
emergency light is needed. Each luminaire must be
connected permanently to the mains power supply.
OPERATION
When the voltage is interrupted, with corresponding
pressings of the button, we can choose the
illumination of 100%, 50%, 33% or turned off, either
to increase the autonomy time or not to consume the
battery power unnecessarily. This option is canceled
when the power network is restored.
1. Every test, installation or maintenance procedure
batteries must be disconnected by removing the
3. The replacement of the battery and the light
5. It is not allowed to discard batteries in to
common trash bins, they must be discarded
only in battery recycling points. Do not
incinerate.
WARNING !!!
must be done only by qualified personnel.
2. The unit must be connected to the mains power
person.
source must be done using parts of the same
supply using a line fuse rated accordingly.
type, by the manufacturer or by a competent
4. If the luminaire must be isolated from the mains
power supply for more than 2 months then the
battery connectors.
LABELING EXPLANATION:
X: Self contained
0: Non Maintained (*)
A: Including test device
*90: 1.5 hour duration
(*)Non Maintained operation: The luminaire lights its
illumination source, only in power supply’s failure.
180: 3 hour duration
NOTE: LED= Light Emitting Diode
INDICATION LED STATUS (with the mains power supply connected)
CHARGE POWER
Disconnected battery / not charging
Charged battery Normal operation mode
No mains power supply
Indicator ONIndicator OFF
Olympia Electronics guarantees the quality, condition and operation of the goods. The period of warranty is
specified in the official catalogue of Olympia Electronics and also in the technical leaflet, which
accompanies each product. This warranty ceases to exist if the buyer does not follow the technical
instructions included in official documents given by Olympia Electronics or if the buyer modifies the goods
provided or has any repairs or re-setting done by a third party, unless Olympia Electronics has fully agreed
to them in writing. Products that have been damaged can be returned to the premises of our company for
repair or replacement, as long as the warranty period is valid.
Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge the
buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or not the
buyer the transportation cost.
WARRANTY
HEAD OFFICE
72nd km. O.N.R. Thessaloniki-Katerini
P.C. 60300 P.O. Box 06 Εginio Pierias Greece
www.olympia-electronics.com
[email protected]
Page 2 from 3923021042_09_005
X0108 A

3. Install the battery cable connectors to the batteries taking care of the polarity, black cable (-) and red cable (+).
Battery replacement
2. Disconnect the cables and remove the old battery.
It can be done only by a competent person and after the mains interruption
1. Use the supplied mounting accessories to mount the device (Fig1).
2. Remove the four cover retaining screws (Fig 1).
4. Always use in any case round mains cable, with external diameter of 6-9mm (H05RN-F type 2x1mm² or any
other type, at least equal to it’s mechanical and electrical properties). ATTENTION!! The cable must not be
deformed in any way (This requirement is important to ensure the tightness isolation IP65). Install the cable
gland, pass the round cable through and tighten it all the way.
5. Connect the cables to the respective positions in the terminal block L for phase and N for neutral.
6. Reinstall the front cover and fasten the retaining screws. (Tightening torque 1Nm).
WARNING!! After the installation has finished, charge the batteries for at least 24 hours so as to obtain the rated
autonomous duration.
1. Follow the step 2 of the installation procedure.
3. Connect the new battery with the same type (step 3 of the installation procedure) and place it in the position of
the old one.
4. Follow the step 6 of the installation procedure and power the device.
Page 3 from 3923021042_09_005
The light source of this luminaire is not replaceable when the light source reaches its end of life the
whole luminaire shall be replaced.
Do NOT stare at operating light source.The luminaire should be positioned so that prolonged staring
into the luminaire at a distance closer than 1.2m is not expected. E = 904.8 lux.
thr
INSTALLATION PROCEDURE (For wall mounting only)
TEST
button
Fig. 1
Power
indicator
Mounting holes
Charge
indicator
Cover
retaining
screws
4
N
L
3