olympia electronics GR-938/4P User manual

220-240V AC/50-60Hz
ABS/PC, PC
3 h90 min
24 h
Charge, lamp fault, fault indication LED, TEST button
From overcharge and deep discharge
IP65
EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3
o
5 to 40 C
Up to 95%
360 x 145 x 73 mm
915gr. 1005gr.
GR-938/4P GR-938/6P GR-939/6P GR-939/4P
4.8V/1.5Ah 4.8V/3Ah 4.8V/4Ah(Ni-MH)
5.2W/5.5 VA 6.1W/6.4 VA4.6W/5 VA 5.8W/6.2 VA
1060gr.
TECHNICAL CHARACTERISTICS (for LED MODULE Specs. see page 4)
4 white power LED’s
175lm / 350lm 245lm / 480lm 175lm / 350lm 245lm / 480lm
6 white power LED’s 6 white power LED’s 4 white power LED’s
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
EXTERNAL DIMENSIONS
CONSTRUCTION MATERIALS
TYPICAL WEIGHT
GUARANTEE
OPERATION VOLTAGE
MAXIMUM POWER CONSUMPTION
BATTERIES (Ni-Cd)
CHARGING TIME
INDICATIONS - CONTROLS
BATTERY PROTECTION
MINIMUM AUTONOMOUS DURATION
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
ILLUMINATION (MAINS / EMERGENCY)
ILLUMINATION SOURCE
3 years (1 year for the battery)
GENERAL
These luminaires are used in places where
emergency luminaires are needed. Each
luminaire must be permanently connected to
mains power supply. In normal operation the
led strip lights and the battery is charging. In
case of a mains power supply failure the
luminaire will light the led strip automatically
in emergency mode. When the mains power
supply is restored the device turns to normal
operation.
INSTALLATION
To install the luminaire follow the installation
instructions on page 3.
OPERATION
Battery Cut-off
The luminaire enters in this operation when the
mains power supply fails and battery has lost
its energy. During this operation the luminaire
enters the idle state and battery consumption is
negligible, in order to be protected from deep
discharge.
Battery charging
The battery charging is completely controlled.
In this case, is achieved the perfect battery
maintenance , as well as the elongation of its
duration. When the battery has completely
charged, it charges with a maintenance
current.
Manual Test
The manual test can be conducted only if the
main power supply and the battery is
connected. By pressing the TEST/RESET
button briefly (page 3) an operation test is
initiated. During this test period all indication
LEDs are OFF.
Automatic test
This test includes all the operations that provide
the manual test and is conducted automatically
every 15 days. In order to be performed, the
main power supply and the battery should be
connected.
Automatic Autonomous Test
The Automatic Autonomous Test is conducted
and measures the luminaire`s back up
operation. This test is conducted automatically
every six months. In order to be performed, the
main power supply and the battery should be
connected (the battery should be charged). If
the battery is not charged, the test is postponed
until the battery is completely charged. If the
luminaire’s duration is lower than the named
during the Automatic Autonomous Test, the
battery must be replaced.
Back Up Operation
The autonomous duration of battery during
emergency mode is at least the one that is
stated in the technical characteristics. During
emergency mode, a LED strip test is also
performed.
Resetting Errors
Push the TEST/RESET button for 5 seconds, to
extinguish all the indicated LED errors (page 3).
Then the luminaire enters regular operation
WATERPROOF SELF TESTING ΜΑΙΝΤΑΙΝΕD EMERGENCY LUMINAIRES
Page 1 from 4 923939008_09_017
Thank you for your trust in our products.
Olympia Electronics - European manufacturer.

Page 2 from 4
mode.
Indication LED status
(with connected mains power supply).
Charge
On: Good charge current.
Οff: No battery (No charging current or
disconnected battery).
Lamp fault
Οn: Faulty LED strip.
Off: Good LED strip.
Fault
Οff: Battery OK.
Blink (With Charge LED ON): Autonomy or low
battery problem
(the battery must be replaced).
Blink (With Charge LED Off):
No charging current or disconnected battery.
ΑΤΤΕΝΤΙΟΝ!!!
1. Operations for installation, maintainance or
testing must be done by authorized personnel
only.
2. The device must be connected to the mains
power supply through a fuse depended on the
total amount of the line’s power load.
In case of battery or lamp replacement, these
must be replaced by parts of the same type, by
the manufacturer or by a competent person.
t i
in battery recycling
points. Do not incinerate.
3.
4. In case of inactive use for a period greater
than 2 months, disconnect the battery by pulling
out the battery’s connector.
5. I s not allowed to discard batteries in to
common trash bins, they must be
discarded only
923939008_09_017
(*) Maintained operation: The luminaire lights its illumination source, when it is powered by
the mains power supply or not.
Non Maintained operation: The luminaire lights its illumination source, only in power
supply’s failure.
Note!! The installer should fill in, on the specification label,
the letter G if the luminaire is used as a safety sign.
X 1 9* 0A G
NOTE: LED= Light Emitting Diode
LABELING EXPLANATION:
X: Self contained
1: Maintained (*)
A: Including test device
G: Internally illuminated
*90: 1.5 hour duration
180: 3 hours duration

Page 3 from 4 923939008_09_017
67
Manual TEST or Resetting Errors
In order to test or reset the device you
must carefully remove the diffusor by
unfastening the 4 mounting screws.
Then push the button as described in
the according paragraphs on page 1.
8
L1 L N N
L
N
L
L1 L N L1 L N
External
switch
Controlled operation of the lamp
Link
Permanent maintained operation
1 Remove the diffusor. Place simultaneously a flat blade screwdriver and pull up gently the
reflector.
2 Install the included plastic cover in to the unused hole and install the base plastic (with the
included mounting screws and plugs).
3 Always use in any case round mains cable, with external diameter of 6-9mm (H05RN-F
type 2x1mm² or any other type, at least equal to it’s mechanical and electrical properties).
ATTENTION!! The cable must not be deformed in any way (This requirement is important
to ensure the tightness isolation IP 65). Install the cable gland, pass the round cable thru and
tighten it all the way.
4 Place the battery’s connector to the corresponding connector on the P.C.B.
5 Connect the mains cables to the respective terminal block (connect the ground wire if required).
6 Ν for neutral, L for live wire and L1 for the maintained operation. The L1 wire can be connected
to an external switch to control the maintained or non maintained operation of the luminaire.
7 For permanent maintained operation use two wires to power the luminaire, Ν for neutral and L for
live wire, and link the L and L1.
8 Install the included tie (if needed) to fasten securely the power cables.
9 Refit the reflector and fasten the two small screws (included).
10 Finaly place the diffusor by using the 4 included screws (tightening torque 1.2 Nm).
INSTALLATION INSTRUCTIONS
234
5
910
1
Battery replacement
1. Unfasten the 4 retaining screws (step 10 of the installation instructions) and remove the
diffusor.
2. Unfasten the 2 retaining screws step 9 of the installation instructions and remove the reflector.
3. Remove the old battery and place a new on of the same type and characteristics.
4. Replace the removed parts (previous steps 1,2).
NOTE!! After finishing the installation you must power the luminaire at least for 24 hours
for battery charging to perform the named autonomy.

Page 4 from 4 923939008_09_017
LED MODULE CHARACTERISTICS
Olympia Electronics Α.Ε.
65 °C max. across the board
Cable connection between main pcb and led module
11.6-13.6VDC
4W 6W
2111143 2211143
GR-938/6P GR-938/4P GR939/6P GR-939/4P
Manufacturer
Model Number
Voltage Range
Connections
Nominal Power
Temperature (tc)
The light source contained in this luminaire shall only be replaced by the manufacturer, or his
agent, or a similar qualified person.
NOTE! The light source is non-user replaceable.
WARRANTY
Olympia Electronics guarantees the quality, condition and operation of the goods. The period of
warranty is specified in the official catalogue of Olympia Electronics and also in the technical leaflet,
which accompanies each product. This warranty ceases to exist if the buyer does not follow the
technical instructions included in official documents given by Olympia Electronics or if the buyer
modifies the goods provided or has any repairs or re-setting done by a third party, unless Olympia
Electronics has fully agreed to them in writing. Products that have been damaged can be returned to
the premises of our company for repair or replacement, as long as the warranty period is valid.
Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge
the buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or
not the buyer the transportation cost.
HEAD OFFICE
72nd km. O.N.R. Thessaloniki-Katerini
P.C. 60300 P.O. Box 06 Eginio Pierias Greece
www.olympia-electronics.gr
[email protected]