olympia electronics GR-938/15L/ADR User manual

Page 1 from 5923939015_09_004
GENERAL
These luminaires are used in places where
emergency luminaires are needed. Each
luminaire must be permanently connected to
mains power supply. In normal operation (L1
connected to L) the led strip lights and the battery
is charging. In case of a mains power supply
failure the luminaire will light the led strip
automatically in emergency mode (powered by
its battery). When the mains power supply is
restored the device turns to normal operation.
Address Operation
The luminaires can be connected to a GR-6500
address panel. For address operations refer to
the installation manual of the panel.
For address module connections see page 3.
For dip-switch addressing selection see page 3, 4
and 5.
INSTALLATION
To install the luminaire follow the installation
instructions on page 3.
Battery Charging
The battery charging is completely controlled.
Thereby, the best possible battery maintenance is
achieved, as well as the elongation of its
duration. When the battery has completely
charged, it charges with a maintenance current.
Battery Cut-off
The luminaire enters in this operation when the
mains power supply fails and battery has lost its
energy. During this operation the luminaire enters
the idle state and battery consumption is
negligible, in order to be protected from deep
discharge.
Manual Test
The manual test can be conducted only if the
mains power supply and the battery is connected.
By pressing the TEST/RESET button briefly
(page 3) an operation test is initiated. During this
test period all indication LEDs are OFF.
Tests
Normally the illumination source and the
autonomy tests are programmed by the control
panel and the test results are sent to the control
panel.
If the luminaire is not connected to GR-6500
panel, the following automatic tests executed:
Automatic Operational Test
This test includes all the operations that provide
the manual test and is conducted automatically
every 15 days. In order to be performed, the
mains power supply and the battery should be
connected.
ADDRESSABLE SELF TESTING MAINTAINED EMERGENCY LUMINAIRES WITH WHITE LEDs
220-240V AC/50-60Hz
4.5W / 4.9VA
Bayblend FR3010, transparent polycarbonate
TECHNICAL CHARACTERISTICS (for LED MODULE Specs. see page 5)
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
EXTERNAL DIMENSIONS
CONSTRUCTION MATERIALS
TYPICAL WEIGHT
GUARANTEE
OPERATION VOLTAGE
MAXIMUM POWER CONSUMPTION
BATTERIES (Ni-Cd)
CHARGING TIME
INDICATIONS
BATTERY PROTECTION
MINIMUM AUTONOMOUS DURATION
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
ILLUMINATION (MAINS / EMERGENCY)
ILLUMINATION SOURCE
90min
24h
Charge, Lamp Fault, Battery Fault indication LED
From overcharge and deep discharge
IP65
3.6V/3Ah
210lm / 210lm
30 white LEDs
EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3
o
5 to 40 C
Up to 95%
3 years (1 year for the battery)
950gr.
363 x 145 x 73 mm
3.4W / 3.8VA
GR-938/15L/ADR GR-938/30L/ADR GR-939/15L/ADR GR-939/30L/ADR
3.6V/0.6Ah
105lm / 105lm
15 white LEDs
180min
5.3W /5.6VA3.3W / 3.7VA
3.6V/1.5Ah
210lm / 210lm 105lm / 105lm
30 white LEDs 15 white LEDs
810gr. 880gr.
Thank you for your trust in our products.
Olympia Electronics - European manufacturer.

Automatic Autonomous Test
The Automatic Autonomous Test is conducted
and measures the device’s back up operation
and emergency duration. This test is conducted
automatically every 6 months. In order to be
performed, the mains power supply and the
battery should be connected and fully charged. If
the battery is not fully charged, the test is
postponed until the battery is completely
charged. If during this test, the autonomy is less
than nominal then the battery fault led turned on
continuously and the battery must be replaced.
Back Up Operation
The autonomous duration of battery during
emergency mode is at least the one that is stated
in the list of the technical characteristics. During
emergency mode, a light source test is also
performed.
Resetting Errors
Push the TEST/RESET button for 5 seconds, to
delete all the indicated LED errors (page 3). Then
the luminaire enters regular operation mode.
Indication LED status (with connected mains
power supply).
Charge
On: Good charge condition.
Οff: No battery (No charging current
or disconnected battery).
Lamp Fault with L1 connected to L
Οn (with LED strip off): Faulty LED strip (must
be replaced).
Οn (with LED strip on): Problem in the back up
circuit of the LED strip (must be checked by an
authorized personnel).
Off: Good LED strip.
Battery Fault
Οff: Battery OK.
Blink (With Charge LED ON): Autonomy or low
battery problem (the battery must be replaced).
Blink (With Charge LED Off): No charging
current or disconnected battery.
ΑΤΤΕΝΤΙΟΝ!!!
1. Operations for installation, maintainance or
testing must be done by authorized personel
only, after a mains interruption.
2. The device must be connected to the mains
power supply through a fuse dependent on the
total amount of the line’s power load.
3. In case of battery or lamp replacement, these
must be replaced by parts of the same type, by
the manufacturer or by a competent person.
4. In case of inactive use for a period greater
than 2 months, disconnect the battery by pulling
out the battery’s connector.
5. I s not allowed to discard batteries in to t i
co mmo n tr ash bin s, t he y mu s t b e
discarded only in battery recycling
points. Do not incinerate.
NOTE: LED= Light Emitting Diode
L A B E L I N G E X P L A N A T I O N :
X: Self contained
1: Maintained (*)
A: Including test device
B: Including remote rest mode
C: Including inhibiting mode
G: Internally illuminated
*90: 1.5 hour duration
180: 3 hours duration
(*) Maintained operation: The luminaire lights its
illumination source, when it is powered by the
mains power supply or not.
Non Maintained operation: The luminaire lights its
illumination source, only in power supply’s failure.
Note!! The installer should fill in, on the
specification label, the letter G if the luminaire is
used as a safety sign.
NOTE!! After finishing the installation you
must power the luminaire at least for 24 hours
for battery charging to perform the nominal
autonomy.
Battery replacement
It can be done only by a competent person
and after the mains interruption.
1. Unfasten the 4 retaining screws (not all the
way) (step 10 of the installation instructions) and
remove the diffusor.
2. Unfasten the 2 retaining screws (step 9 of the
installation instructions) and remove the reflector.
3. Remove the old battery and place a new one
of the same type and characteristics.
4. Replace the removed parts (previous steps
1,2).
The light source contained in this luminaire
shall only be replaced by the manufacturer,
or his agent, or a similar qualified person.
NOTE! The light source is non-user replaceable.
923939015_09_004
Page 2 from 5
X1 81 0A B C G

INSTALLATION INSTRUCTIONS FOR WALL OR CEILING MOUNTING
9
67
Manual TEST or Resetting Errors
In order to test or reset the device you
must carefully remove the diffusor by
unfastening the 4 mounting screws.
Then push the button as described in
the according paragraphs on page 1
and 2.
1
8
10
L1 L N N
L
N
L
L1 L N L1 L N
External
switch
Controlled operation of the lamp
Link
Permanent maintained operation
1 Remove the diffusor. Place a flat blade screwdrivers and pull up gently the reflector.
2 Install the included plastic cover in to the unused hole and install the base plastic (with the
included mounting screws and plugs).
3 Always use in any case round mains cable, with external diameter of 6-9mm (H05RN-F
type 2x1mm² or any other type, at least equal to it’s mechanical and electrical properties).
ATTENTION!! The cable must not be deformed in any way (This requirement is important
to ensure the IP rating). Install the cable gland, pass the round cable through and tighten it all
the way.
4 Place the battery’s connector to the corresponding connector on the P.C.B.
5 Connect the mains cables to the respective terminal block (connect the ground wire if required).
6 Ν for neutral, L for live wire and L1 for the maintained operation. The L1 wire can be connected
to an external switch to control the maintained or non maintained operation of the luminaire.
7 For permanent maintained operation use two wires to power the luminaire, Ν for neutral and L for
live wire, and link the L and L1.
8 Install the included tie (if needed) to fasten securely the power cables.
9 Refit the reflector and fasten the two small screws (included).
10 Finally place the diffusor by using the 4 included screws (tightening torque 1.2 Nm).
234
5
11 To connect the address cables, remove the detachable terminal blocks and perform the
connections.
12 Attach the removed terminal blocks and address the luminaire by using the dip-switches (see
page 4 and 5). Attention!! The dip-switches 9 and 10 must be in off position
Address connections
12 GR-6500 Loop
LL
L
L
L
L
11
Page 3 from 5923939015_09_004

Address Dipswitch
setting Address Dipswitch setting Address Dipswitch setting Address Dipswitch setting Address Dipswitch setting Address Dipswitch setting
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
1
ON
2345678 1
ON
2345678 1
ON
2345678
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
1
ON
2345678
1
ON
2345678
1
ON
2345678
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
2
3
4
1
ON
2345678
1151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
1
ON
2345678 1
ON
2345678
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
121
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
122
123
124
923939015_09_004
Page 4 from 5

197 1
ON
2345678
198 1
ON
2345678
199 1
ON
2345678
200 1
ON
2345678
201 1
ON
2345678
202 1
ON
2345678
203 1
ON
2345678
195 1
ON
2345678
196 1
ON
2345678
204 1
ON
2345678
Address Dipswitch
setting
189 1
ON
2345678
191 1
ON
2345678
193 1
ON
2345678
181 1
ON
2345678
182 1
ON
2345678
183 1
ON
2345678
184 1
ON
2345678
185 1
ON
2345678
186 1
ON
2345678
187 1
ON
2345678
188 1
ON
2345678
190 1
ON
2345678
192 1
ON
2345678
194 1
ON
2345678
Address Dipswitch
setting
207
208
1
1
ON
ON
2
2
3
3
4
4
5
5
6
6
7
7
8
8
205 1
ON
2345678
206 1
ON
2345678
209
210
1
1
ON
ON
2
2
3
3
4
4
5
5
6
6
7
7
8
8
211
213
212
214
215
216
217
218
219
220
1
1
1
1
1
1
1
1
1
1
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
221
222
1
1
ON
ON
2
2
3
3
4
4
5
5
6
6
7
7
8
8
241 1
ON
2345678
242 1
ON
2345678
243 1
ON
2345678
244 1
ON
2345678
245 1
ON
2345678
246 1
ON
2345678
247 1
ON
2345678
248 1
ON
2345678
249 1
ON
2345678
250 1
ON
2345678
229 1
ON
2345678
230 1
ON
2345678
231 1
ON
2345678
232 1
ON
2345678
233 1
ON
2345678
234 1
ON
2345678
235 1
ON
2345678
236 1
ON
2345678
237 1
ON
2345678
238 1
ON
2345678
239 1
ON
2345678
240 1
ON
2345678
223 1
ON
2345678
225 1
ON
2345678
224 1
ON
2345678
226 1
ON
2345678
227 1
ON
2345678
228 1
ON
2345678
Address Dipswitch
setting
Address Dipswitch
setting Address Dipswitch setting
923939015_09_004
Page 5 from 5
WARRANTY
Olympia Electronics guarantees the quality, condition and operation of the goods. The period of
warranty is specified in the official catalogue of Olympia Electronics and also in the technical
leaflet, which accompanies each product. This warranty ceases to exist if the buyer does not
follow the technical instructions included in official documents given by Olympia Electronics or if
the buyer modifies the goods provided or has any repairs or re-setting done by a third party,
unless Olympia Electronics has fully agreed to them in writing. Products that have been damaged
can be returned to the premises of our company for repair or replacement, as long as the warranty
period is valid.
Olympia Electronics reserves the right to repair or to replace the returned goods and to or not
charge the buyer depending on the reason of defection. Olympia Electronics reserves the right to
charge or not the buyer the transportation cost.
HEAD OFFICE
72nd km. O.N.R. Thessaloniki-Katerini
P.C. 60300 P.O. Box 06 Eginio Pierias Greece
www.olympia-electronics.gr
[email protected]
LED MODULE CHARACTERISTICS
Olympia Electronics S.A
45 °C max. across the board
Cable connection with non reversible connectors
8.7-10.8 V DC
1W 2W
1605163/15L 1605163/30L
GR-938/15L/ADR GR-939/15L/ADR GR-938/30L/ADR GR-939/30L/ADR
Manufacturer
Model Number
Voltage Range
Connections
Nominal Power
Temperature (tc)