olympia electronics GR-1938/4P User manual

Page 1 from 4923193903_09_003
GENERAL
These luminaires are used in places where
emergency luminaires are needed.
Each luminaire must be perman e n t l y
connected to mains power supply.
In normal operation (L1 connected to L) the
led strip lights and the battery is charging.
In case of a mains power supply failure
the lumin a i r e wi l l n lig h t t he l e d s tri p
automatically in emergency mode (powered by
its battery). When the mains power supply
is restored the device turns to normal
operation.
INSTALLATION
To install the luminaire follow the installation
instructions on page 3.
Battery Charging
The battery charging is completely controlled.
Thereby, the best possible battery
maintenance is achieved, as well as the
elongation of its duration. When the battery
has completely charged, it charges with a
maintenance current.
Battery Cut-off
The luminaire enters in this operation when
the mains power supply fails and battery has
lost its energy. During this operation the
luminaire enters the idle state and battery
consumption is negligible, in order to be
protected from deep discharge.
Manual Test
This test can be done by placing the test card
on the side of the indications (page 4) and
remove it instantly an operation test is
initiated. The light source and the emergency
circuit of the device is monitored. The manual
test can be conducted only if the main power
supply and the battery is connected. During
this test period all indication LEDs are OFF.
Automatic Operational Test
This test includes all the operations that
provide the manual test and is conducted
automatically every 15 days. In order to be
performed, the mains power supply and the
battery should be connected.
Automatic Autonomous Test
The Automatic Autonomous Test is conducted
and measures the device’s back up operation
and emergency duration. This test is
conducted automatically every 6 months. In
order to be performed, the mains power
WATERPROOF SELF TESTING MAINTAINED EMERGENCY LUMINAIRES WITH LEDs
Thank you for your trust in our products
Olympia Electronics - European manufacturer
220-240V AC/50-60Hz
TECHNICAL CHARACTERISTICS (for LED MODULE Specs see page 4)
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
EXTERNAL DIMENSIONS
CONSTRUCTION MATERIALS
TYPICAL WEIGHT
GUARANTEE
OPERATION VOLTAGE
MAXIMUM POWER CONSUMPTION
BATTERY (Ni-Cd)
CHARGING TIME
INDICATIONS
BATTERY PROTECTION
MINIMUM AUTONOMOUS DURATION
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
ILLUMINATION (MAINS / EMERGENCY)
ILLUMINATION SOURCE
90min
24h
Charge, Lamp Fault, Battery Fault LED
From overcharge and deep discharge
IP 65
EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3
o
5 to 40 C
Up to 95%
3 years (1 year for the battery)
180min
313 x 118 x 66 mm
Bayblend FR3010, transparent polycarbonate
6.2W / 6.5VA
4.8V/4Ah (NiMH)
245lm / 480lm
862gr.
4.7W / 5.1VA
4.8V/1.5Ah
175lm / 350lm
6.2W / 6.5VA5.3W / 5.7VA
4.8V/3Ah
175lm / 350lm 245lm / 480lm
725gr. 810gr.
6 power LED 6 power LED
4 power LED4 power LED
GR-1938/4P GR-1939/4P GR-1939/6PGR-1938/6P

Page 2 from 4
supply and the battery should be connected
and fully charged. If the battery is not fully
charged, the test is postponed until the battery
is completely charged. If during this test, the
autonomy is less than nominal then the battery
fault led turned on continuously and the
battery must be replaced.
Back Up Operation
The autonomous duration of battery during
emergency mode is at least the one that is
stated in the list of the technical
characteristics. During emergency mode, a
light source test is also performed.
Resetting Errors
Place the test card A-1900 on the side of the
indications (page 4) and remove it after the
reset is conducted (the indications light in
sequence), to delete all the indicated LED
errors. Then the luminaire enters regular
operation mode.
Indication LED status (with connected
mains power supply).
Charge
On: Good charge condition.
Οff: No battery (No charging current
or disconnected battery).
Lamp Fault with L1 connected to L
Οn (with LED strip off): Faulty LED strip
(must be replaced).
Οn (with LED strip on): Problem in the back
up circuit of the LED strip (must be checked by
an authorized personnel).
Off: Good LED strip.
Battery Fault
Οff: Battery OK.
Blink (With Charge LED ON): Autonomy or
low battery problem (the battery must be
replaced).
Blink (With Charge LED Off): No charging
current or disconnected battery.
ΑΤΤΕΝΤΙΟΝ!!!
1. Operations for installation, maintainance or
testing must be done by authorized personnel
only.
2. The device must be connected to the mains
power supply through a fuse dependent on the
total amount of the line’s power load.
3. In case of battery or lamp replacement,
these must be replaced by parts of the same
type, by the manufacturer or by a competent
person.
4. In case of inactive use for a period greater
than 2 months, disconnect the battery by
pulling out the battery’s connector.
5. I s not allowed to discard batteries in to t i
common trash bins, they must be
discarded only in battery recycling
points. Do not incinerate.
NOTE: LED= Light Emitting Diode
LABELING EXPLANATION:
X: Self contained
1: Maintained (*)
A: Including test device
G: Internally illuminated safety sign
*90: 1.5 hour duration
180: 3 hours duration
(*) Maintained operation: The luminaire lights
its illumination source, when it is powered by
the mains power supply or not.
Non Maintained operation: The luminaire lights
its illumination source, only in power supply’s
failure.
Note!! The installer should fill in, on the
specification label, the letter G if the luminaire is
used as a safety sign.
NOTE!! After finishing the installation you
must power the luminaire at least for 24
hours for battery charging to perform the
nominal autonomy.
Battery replacement
It can be done only by a competent person
and after the mains interruption
1. Follow the step 1 of the installation
insrtuctions and remove the diffusor.
2. Remove the reflector (step 1 of the
installation instructions).
3. Remove the old battery and place a new on
of the same type and characteristics.
4. Replace the removed parts (previous steps
1, 2).
The light source contained in this
luminaire shall only be replaced by the
manufacturer, or his agent, or a similar
qualified person.
N O T E ! T h e l i g h t s o u r c e i s n o n - u s e r
replaceable.
923193903_09_003
X1 81 0A G

Page 3 from 4
1 Unclip the plastic latches with a flat blade screwdriver, unfasten the 2 screws (not all the
way, step 10 B) and remove the diffusor. Place a flat blade screwdriver to the recesses
and pull up gently the reflector.
2 Install the base plastic (with the included mounting screws and plugs). WARNING!! To
preserve the ΙΡ65 rating, fit the screws with the metallic washers and plastic rings
which are included.
3 Always use in any case round mains cable, with external diameter of 5-10mm
(H05RN-F type 2x1mm² or any other type, at least equal to it’s mechanical and
electrical properties).
ATTENTION!! The cable must not be deformed in any way (This requirement is
important to ensure the ΙΡ65 rating). Install the gasket and make a hole in the center by
using a small screwdriver. Pass the round cable through the gasket. Install the second
included gasket in to the unused hole.
4 Place the battery’s connector to the corresponding connector on the P.C.B.
5 Connect the mains cables to the respective terminal block.
6 Ν for neutral, L for live wire and L1 for the maintained operation. The L1 wire can be
connected to an external switch to control the maintained or non maintained operation of
the luminaire.
7 For permanent maintained operation use two wires to power the luminaire, Ν for neutral
and L for live wire, and link the L and L1.
8 Install the included tie to fasten securely the power cables.
9 Refit the reflector (mind the holes of the indications).
10 Finally place the diffusor (mind the holes of the indications). Attention!! First the plastic
latches (A) must be secured (click sound) and then fasten the 2 screws (B)
(tightening torque 1.2 Nm).
INSTALLATION INSTRUCTIONS FOR WALL OR CEILING MOUNTING
8
5
4
Charge
Lamp fault
Battery fault
Indications
7
N
L
Link
Permanent maintained operation
6
N
L
External
Switch
Controlled operation of the lamp
10
A
ABB
923193903_09_003
9
1
2
3

A-1900
Test card
Manual TEST or Resetting Errors with
the A-1900 Test card (not included
and is available only on request). In
order to test or reset the device you
must place the card on the side of the
indications and remove it instantly for
TEST or remove it after the reset is
conducted (the indications light in
sequence).
Page 4 from 4923193903_09_003
WARRANTY
Olympia Electronics guarantees the quality, condition and operation of the goods. The period of
warranty is specified in the official catalogue of Olympia Electronics and also in the technical leaflet,
which accompanies each product. This warranty ceases to exist if the buyer does not follow the
technical instructions included in official documents given by Olympia Electronics or if the buyer
modifies the goods provided or has any repairs or re-setting done by a third party, unless Olympia
Electronics has fully agreed to them in writing. Products that have been damaged can be returned to
the premises of our company for repair or replacement, as long as the warranty period is valid.
Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge
the buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or
not the buyer the transportation cost.
HEAD OFFICE
72nd km. O.N.R. Thessaloniki-Katerini
P.C. 60300 P.O. Box 06 Εginio Pierias Greece
www.olympia-electronics.gr
[email protected]
LED MODULE CHARACTERISTICS
Olympia Electronics S.A.
Non reversible connection between main pcb and led module
11.6-13.6 V DC
4W 6W
1509153/4P 1509153/6P
GR-1938/4P
GR-1939/4P
GR-1938/6P GR-1939/6P
65 °C max. across the board
Manufacturer
Model Number
Voltage Range
Connections
Nominal Power
Temperature (tc)