olympia electronics GR-900/30L/SC User manual

GENERAL
This luminaire is used in places where
emergency luminaires are needed.
Each luminaire must be permanently
connected to mains power supply.
In normal operation the led strip lights and the
capacitor is charging.
In case of a mains power supply failure
the luminaire will light the led strip
automatically in emergency mode. When the
mains power supply is restored the device
turns to normal operation.
INSTALLATION
To install the luminaire follow the installation
instructions on page 3.
Capacitor charging
The capacitor charging is completely and
accurately controlled. In this case, is achieved
the perfect capacitor maintenance, as well as
the elongation of its duration. When the
capacitor has completely charged, it charges
with a maintenance current.
Capacitor Cut-off
The luminaire enters in this operation when
the mains power supply fails and capacitor has
lost its energy. During this operation the
luminaire enters the idle state and the
capacitor’s consumption is negligible.
Manual Test
The manual test can be conducted only if the
main power supply and the capacitor is
connected. By pressing the TEST/RESET
button briefly (page 3) an emergency operation
test is initiated. During this test period all
indication LEDs are OFF and the whole
emergency circuit is monitored.
Automatic Operational Test
This test includes all the operations that provide
the manual test and is conducted automatically
every 15 days. In order to be performed, the
main power supply and the capacitor should be
connected.
Manual Autonomous Test
If the Test button is pressed for a period
between 5 to 10 seconds (with the capacitor
fully charged), the illumination sign will enter in
counting autonomy condition. If the capacitor is
not fully charged this command is ignored.
The BAT FAULT LED blinks during the
measurement, indicating this process to the
user. This measurement duration is equal with
the nominal autonomous duration of the
luminaire and at the end of the process, if the
measured duration was at least the nominal
autonomous duration, the BAT FAULT LED is
turned OFF, in the other hand stays
continuously ON indicating to the user that the
capacitor must be replaced.
Automatic Autonomous Test
The Automatic Autonomous Test is conducted
and measures the luminaire’s sign’s back up
operation and emergency duration. This test is
conducted automatically every six months. In
order to be performed, the main power supply
Page 1 from 4
GR-900/30L/SCWaterproof Self Testing Maintained Emergency Luminaire
220-240V AC/50-60Hz
TECHNICAL CHARACTERISTICS (for LED module specifications see page 4)
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
EXTERNAL DIMENSIONS (L x W x H)
TYPICAL WEIGHT
GUARANTEE
OPERATION VOLTAGE
MAXIMUM POWER CONSUMPTION
BACK UP SOURCE
CHARGING TIME
INDICATIONS - CONTROLS
CAPACITOR PROTECTION
MINIMUM AUTONOMOUS DURATION
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
LIGHT SOURCE INTENSITY
ILLUMINATION SOURCE
3h
CHARGE, LAMP FAULT, BAT FAULT, TEST button
From overcharge
-30 to 40 C
o
Up to 95%
10 years
363x 145 x 73 mm
White LEDs
7W / 7.5VA /PF: 0.93
923900000_09_007
IP65
60 min
250lm / 95lm (emergency)(230V AC)
1055gr.
Ultra Capacitor A-900
EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3
Thank you for your trust in our products
Olympia Electronics - European manufacturer

Page 2 from 4
and the capacitors should be connected and
fully charged. If the capacitor is not fully
charged, the test is postponed until the
capacitor is completely charged.
Back Up Operation
The capacitor’s autonomous duration during
emergency mode is at least the one that is
stated in the list of the technical
characteristics. During emergency mode, a
LED strip test is also performed.
Resetting Errors
Push the TEST/RESET button (page 3) for
>10 seconds, to delete all the indicated LED
errors . Then the illumination sign enters
regular operation mode.
Test switch
Pressing the test switch less than 5 seconds
will initiate a light source test (last for 3 secs).
Pressing the test switch between 5 to 10
seconds will initiate a manual capacitor
duration test. This test will not be started if the
capacitor is not fully charged (i.e. If the green
LED is flashing). If the test switch is pressed
for more than 10 seconds, the illumination sign
will be reset (delete all errors).
ΑΤΤΕΝΤΙΟΝ!!!
1. Operations for installation, maintainance or
testing must be done by authorized personel
only.
2. The luminaire must be connected to the
mains power supply thru a fuse dependent by
the total amount of the line’s power load.
3.In case of capacitors or lamp replacement,
these must be replaced by parts of the same
type, by the manufacturer or by a competent
person.
t i
in battery recycling
points. Do not incinerate.
4. In case of inactive use for a period greater
than 2 months, disconnect the battery by
pulling out the battery’s connector when is
fully charged.
5. I s not allowed to discard batteries in to
common trash bins, they must be
discarded only
923900000_09_007
Status of LEDs
Led status explanation
GREEN
YELLOW
RED
Normal
Charging
C duration test (auto or manual)apacitor’s
Capacitor’s fault
Capacitor’s fault and light source fault
Charger and fault (or mains off and battery fault)capacitor’s
Charger and light source fault (or mains off and fault)light source
Charger, and light source fault (or mains off, capacitor and fault)capacitor light source
Light source test
Light source fault
Continuous ON Continuous OFF Flashing at 1,2 Hz
Charger’s fault, capacitor not connected or mains off
LEDs Description

Page 3 from 4
INSTALLATION INSTRUCTIONS
For wall or ceiling installation
Step 1. Remove the diffuser. Place a flat blade screwdriver and pull up gently the reflector.
Step 2. Install the included plastic cover in to the unused hole and install the base plastic (with the
included mounting screws and plugs).
Step3.Alwaysuseinanycaseroundmainscable,withexternaldiameterof6-9mm(H05RN-F
type 2x1mm² or any other type,at least equal to it’s mechanical and electrical properties).
ATTENTION!! The cable must not be deformed in any way (This requirement is important
to ensure the tightness isolation IP 65). Install the cable gland,pass the round cable through
and tighten it all the way.
Step 4. Place the capacitor’s connector to the corresponding connector on the P.C.B.
Step 5. Connect the mains cables to the respective terminal block (connect the ground wire if
required). Νfor neutral, Lfor live wire and L1 for the maintained operation. The L1wire can be
connected to an external switch to control the maintained or non maintained operation of the
luminaire. For permanent maintained operation use two wires to power the luminaire, Νfor neutral
andLforlivewire,andlinktheLandL1.
Step 6. Install the included tie (if needed) to fasten securely the power cables.
Step 7. Refit the reflector and fasten the two small screws (included).
Step 8. Finally place the diffuser by using the 4 screws (tightening torque 1.2Nm).
Step 9. Manual TEST or Resetting Errors
In order to test or reset the device you must carefully remove the diffuser by unfastening the 4
mounting screws. Then push the button as described in the according paragraphs on page 1 and
2.
NOTE!!
After finishing the installation you must power the luminaire at least for 3 hours for
capacitor charging to perform the nominal autonomy.
923900000_09_007
L1 L N
1
4
7
2 3
5
8
6
9

Page 4 from 4 923900000_09_007
Importantnoticefortheinstalledluminairesinonearea!!!
The installer must connect the ’s connector first and then should power the luminaire.
The capacitor connection must have at least a time variation of 1.5 minute for each luminaire.
Withthisvariation,itis ensured that the non synchronizedAutomaticAutonomousTestfortwoor
moreluminairesinstalledinonearea,isnotconductedinthesameday.
capacitor
Super capacitor replacement (Α-900)
It can be done only by a competent person and after the mains interruption
1. Unfasten the 4 screws (step 8 page 3) and remove the diffuser.Unfasten the 2 retaining
screws and remove the reflector (step 7 page 3).
2. Disconnect the connector and remove the old capacitor pack by untastening the retaining
screws .
3. Connect the new capacitor pack (step 4 of the
installation procedure) place it in the position of the
old one and fasten the removed screws.
4. Refit the removed parts in previous steps and
power the device.
s
s
s
s
(*) Maintained operation: The luminaire lights its
illumination source, when it is powered by the mains
power supply or not.
Non Maintained operation: The luminaire lights its
illumination source, only in power supply’s failure.
Note!! The installer should fill in, on the specification
label, the letter Gif the luminaire is used as a safety
sign.
X1 6
*0A G
NOTE: LED= Light Emitting Diode
LABELING EXPLANATION:
X: Self contained
1: Maintained (*)
A: Including test device
G: Internally illuminated safety sign
*60: 1 hour duration
The light source contained in this luminaire shall only be replaced by the manufacturer, or his
agent, or a similar qualified person.
NOTE! The light source is non-user replaceable.
WARRANTY
Olympia Electronics guarantees the quality, condition and operation of the goods. The period of
warranty is specified in the official catalogue of Olympia Electronics and also in the technical leaflet,
which accompanies each product. This warranty ceases to exist if the buyer does not follow the
technical instructions included in official documents given by Olympia Electronics or if the buyer
modifies the goods provided or has any repairs or re-setting done by a third party, unless Olympia
Electronics has fully agreed to them in writing. Products that have been damaged can be returned to
the premises of our company for repair or replacement, as long as the warranty period is valid.
Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge
the buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or
not the buyer the transportation cost.
HEAD OFFICE
72nd km. O.N.R. Thessaloniki-Katerini
P.C. 60300 P.O. Box 06 Εginio Pierias Greece
www.olympia-electronics.gr
[email protected]
LED MODULE CHARACTERISTICS
Manufacturer
Model Number
Voltage Range
Connections
Nominal Power
Temperature (tc)
Olympia Electronics S.A.
45 °C max. across the board
Cable connection with non reversible connectors
17.4-21.6V DC
2W
GR-900/30L/SC
1505153/30L