olympia electronics BS-413 User manual

921413000_09_008
Page 1 from 4
13,6-14,8V DC
6mA
Bayblend FR3010, clear polycarbonate (red)
USAGE
BATTERY TYPE
For external use
12V/1,3Ah Pb (sealed lead-acid) (not included)
IP20
115 dB / 1m
-10 60 C
o
έως
Up to 95%
2 years (6 months for A-989 battery)
1700gr.
290x95x190mm
BS-413
EN 50130-4, EN 55022, EN 60950-1
TECHNICAL CHARACTERISTICS
RELATIVE HUMIDITY
CONSTRUCTION MATERIAL
WEIGHT
EXTERNAL DIAMENSIONS
GUARANTEE
OPERATION VOLTAGE
QUIESCENT CONSUMPTION
SOUND LEVEL
PRODUCED IN ACCORDANCE WITH
OPERATION TEMPERATURE RANGE
DEGREES OF COVER PROTECTION
Autonomous electronic siren
with beacon for burglar alarm panels
GENERAL tampered with.
The BS-413 alarm siren is of robust design and If you require, the siren to also be activated if the
can be used with conventional burglar alarm siren is dismounted from the wall. you must
panels such as the BS-468. It has a red beacon connect the T1, T2 (TAMPER) inputs.
that blinks when the siren is activated and a In case of maintenance or if the siren is moved
piezo speaker that produces a sound level of from it’s mounting position, the SE (Service)
115dB at 1 meter.input of the siren must be connected to the (-) of
The incorporated tamper mechanism protects the panel and the panel must be set to OFF.
the siren from unauthorized access when the
cables are cut, the cover is removed or when Battery
the siren is unmounted from the wall. If the battery has not been connected then the
siren produces a single tone sound every 1
Mounting second.
It is mounted externally on a flat surface and at Whereas if the battery does not operate
a height of about 2,5 meters. Also it should be correctly, a 3 tone sound is emitted every 12
placed in an area that does not obstruct the hours.
sound.
Beacon
WARNING!!! There is a two position (ON, OFF) jumper on the
All 4 mounting screws must be used. siren which is marked (LED FLASΗ). If a link is
placed on the (ON) position, the beacon blinks
Connection every 4 seconds in the quiescent state. If no
The connection between the siren and the BS- jumper is placed then the beacon is OFF during
468 panel is shown on figure 1.the quiescent state and blinks during the alarm.
After finishing with the connections, connect the
battery cables, install the internal cover and the Start signal
front fascia of the siren by installing the screws There is also another 2 position jumper marked
on the bottom side. Finally remove the cable (TRIGGER) with the positions (-) and (+).
connected to the SE (Service) of the siren from This jumper sets if the trigger in positive or
the (-) of the panel. The siren will sound once to negative. Α positive trigger means that the ST
indicate that it is ready to operate and receive a (START) signal must be a positive voltage for
command from the panel. the siren to be activated.
The siren now charges the battery and is ready
to accept an ALARM signal from the panel or if
the cables are cut. If we connect the Τ1, Τ2
(TAMPER) signals then it will be activated if it is
Thank you for your trust in our products
Olympia Electronics - European manufacturer

Alarm Alarm duration
The siren sounds the alarm in 2 cases, when The siren is activated for as long as an alarm
the ST (START) signal is activated or when it’s signal is issued but stops after 7 minutes. The
power is interrupted. siren will be reactivated with a new alarm signal.
A total of 7 cables are needed for connecting the siren.
2 cables are needed for connecting the siren power supply.
The third cable is used for the ST (START) signal.
The fourth cable is the signal for the beacon FL (FLASH), which in not mandatory for the operation of
the siren.
The fifth cable is for the SE (SERVICE) signal that prevents the siren from sounding during the
installation. It must be connected during the connection procedure and disconnected (from the panel
side) after the installation has finished.
The remaining 2 cables are used for connecting the T1, T2 (TAMPER) inputs of the siren to the Ζ8 zone
TAMPER of the panel. This method permits the siren to sound if tampered with and will also activate the
auto telephone dialer.
1. Mounting points (All four screws
must be used)
2. Inner cover mounting points
3. Piezo megaphone
4. Connection terminals
5. Battery compartment 12V/1,2Ah
6. TAMPER protection mechanism
7. Beacon
8. Cable entry hole
Figure 2 . The main parts of the siren
11
1
1
2
6
2
7
3
4
5
8
Jumpers
921413000_09_008
Page 2 from 4
Installation Instructions

Connections
Z1 Z2 Z3 Z4 Z5 Z6 Z7 Z8 12V12V A B P1 P2 P3 AS ES NO C NC ANT
5K6
Siren BS-413
Figure 1. Connecting a BS-413 siren to the BS-468 panel
Remove this
cable after the installation
has finished
24_H
C C
12V ALARM RELAY SIRENS
NOCNC
TC
EXT AUTO
Remove this
cable after the installation
has finished
Siren
BS-413
Figure 2. Connecting a BS-413 siren to the BS-418 panel
921413000_09_008
Page 3 from 4
SE
T1
T2
+
+
-
++ ST SE T1 T2FL

Figure 3. Connecting a BS-413 siren to the BS-458 panel
Remove this
cable after the installation
has finished
BS-458
N L
P2
P1 Z1
Z2
Z3
Z4
AS
TAMPER
-12V
- - - -
+12V
Siren BS-413
++ ST SE T1 T2FL
5K6
921413000_09_008
Page 4 from 4
WARRANTY
Olympia Electronics guarantees the quality, condition and operation of the goods. The period of
warranty is specified in the official catalogue of Olympia Electronics and also in the technical leaflet,
which accompanies each product. This warranty ceases to exist if the buyer does not follow the
technical instructions included in official documents given by Olympia Electronics or if the buyer
modifies the goods provided or has any repairs or re-setting done by a third party, unless Olympia
Electronics has fully agreed to them in writing. Products that have been damaged can be returned to
the premises of our company for repair or replacement, as long as the warranty period is valid.
Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge
the buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or
not the buyer the transportation cost.
HEAD OFFICE
72nd km. O.N.R. Thessaloniki-Katerini
P.C. 60061 Greece
www.olympia-electronics.gr
[email protected]