Omega Altise OP40R User manual

OP40R
40cm Remote Control
Pedestal Fan
Instruction
Manual

omega altise
2
Important Safety Instructions
1. Read all instructions.
2. Disconnect the power plug before dismantling, assembling or before cleaning.
3. Avoid touching mobile parts of the fan.
4. Make sure the fan is on a dry and even surface.
5. Never insert fingers, pencils or any other objects through the guards whenever
the power plug is connected, especially while running.
6. The appliance is not intended for use by young children or infirm persons unless
they have been adequately supervised by a responsible person to ensure that
they can use the appliance safely.
7. Young children or infirm persons should be supervised to ensure that they do not
play with the appliance.
8. Do not use the appliance for any other purpose than its intended use.
9. The fan must not be used if the guards are not fastened according to
instructions.
10. When the power cord is damaged, it must be replaced by the manufacturer or its
service agent or a similarly qualified person in order to avoid a hazard.
11. Do not use your appliance with an extension cord unless it has been checked
and tested by a qualified electrician or electrical supplier.
Read all instructions before using this unit. Keep them for future reference.
Specifications
Model OP40R Settings 3 speed, timer-off
Rated Voltage 220-240V / 50Hz Fan blade size 40cm
Watts 50W Tilt action Tilting fan head
Dimensions
(h x w x d) mm 1280 x 400 x 400 Oscillation Oscillating fan head
Controls Electronic / Remote Warranty 2 year replacement

omega altise
3
Assembly Instructions
1. Remove all items of packaging from the fan.
2. Insert the pedestal tube into the base plate. Carefully turn
the unit upside down and secure with the L shaped
locking screw as shown in Figure 1. Return to an upright
position.
Figure 1.
Locating lugs
3. Loosen the height adjustment ring and extend the
support pole. Initially the support pole will be held tightly
in place. If necessary, use a pair of pliers to grasp the
support pole and pull it into position. Figure 2.
4. Retighten the height adjustment ring to
prevent slipping, then place the fan
assembly (control panel and motor
casing) onto the pole and tighten the pole
screw manually. Do not over tighten.
5. Remove the blade cap from the motor
shaft by turning it clockwise. Then remove
the locking nut by turning it anti-clockwise.
6. Place the rear grille into position, ensuring that it is aligned
with the locating lugs (see Figure 2). If this is done
correctly, the carry handle on the grille will be at the top.
7. Fix the grille into position by replacing the rear grille locking
nut tightly by hand. Do not force the locking nut (see Figure
2). Figure 3.
8. The groove in the centre of the fan blade aligns with the T-
bar on the motor shaft to ensure it is positioned correctly.
9. Fix the blade into place by gently hand tightening the blade
cap onto the motor shaft in an anti-clockwise direction (see
Figure 3). Do not over tighten.
10. Open all locking clips on the front grille (see Figure 4). Figure 4.
11. Place the front grille into position and secure it by fastening
the clips over the outer rim. The small screw and nut at the
bottom of the grille must be fitted for additional safety. (see
Figure 5).
Figure 5.

omega altise
4
Operating Instructions
1. Use in a dry place, free of excessive humidity and water.
2. When connected to the power the Power LED on the fan control panel will glow.
3. This unit can be operated by the control panel on the fan or by remote control in
the same manner. The corresponding LED on the fan control panel will be
illuminated according to your selection.
ON/OFF: Will turn the fan on and off. The fan will start in
NORMAL mode and LOW fan speed will be selected.
SPEED: Selects the speed of the fan from LOW, MEDIUM
and HIGH.
MODE: There are three types of airflow that can be selected:
1. Normal mode is usual fan function airflow and can be
combined with the 3 fan speeds as desired.
2. Natural mode can be selected in combination with the 3
fan speeds.
a. When HIGH is selected the fan will alternate
between High, Medium and Low speeds.
b. When MEDIUM is selected the fan will alternate
between Medium and Low speeds.
c. When LOW is selected the fan will alternate between
Low speed and OFF.
3. Sleep mode when combined with the 3 fan speeds will:
a. When HIGH is selected the fan will operate at High Natural mode for
30mins, then Medium Natural mode for 30mins, then Low Natural mode for
the remaining time.
b. When MEDIUM is selected the fan will operate at Medium Natural mode for
30mins, then Low Natural mode for the remaining time.
c. When LOW is selected the fan will operate on Low Natural mode.
TIME: Pressing the time key will activate the timer-off function. Each time the key is
pressed the timer will be increased by 30mins up to a maximum of 7.5 hours. When
the timer reaches the set time the fan will stop automatically.
OSC: The oscillation button will start the fan oscillating. Press again for fixed
operation.

omega altise
5
Fan Direction Adjustment
1. Do not attempt to make any adjustment to the direction of the grille and fan
assembly until the fan has been turned off and unplugged from the socket.
2. To adjust the direction of the fan, hold the grille and gently tilt the fan head until
the desired position is reached.
3. Plug the fan back into the socket and turn the fan on.
Care and Maintenance
1. Always disconnect the cord from the electrical outlet when cleaning your fan.
2. Light accumulated dust may be removed from the fan with a soft cloth or vacuum
cleaner using the dusting brush attachment.
3. Wipe the exterior surfaces of the fan occasionally with a cloth moistened (not
dripping wet) with a mild soap solution. Dry the case thoroughly with a soft dry
cloth before operating the fan.
4. Avoid the use of gasoline, benzine, thinner etc as they may result in damage to
the fan.
5. Store the fan in a clean dry place when not in use.
CAUTION! Do not immerse the fan in water or allow water to drip into
the interior of the fan housing as this could create a fire or electric
shock hazard.
WARNING! Do not attempt to open or repair the fan yourself. Doing so
could void the warranty and cause damage or personal injury.
Omega Altise products are distributed in Australia by MEA,
(A Division of Hagemeyer Brands Australia Pty Ltd)
ABN 28 001 375 686
Locked Bag 4013, Kingsgrove NSW 2208
Phone: [phone]
Fax: [phone]
Email: [email protected]
Web: meaappliances.com.au