Omega Altise OT99B User guide

OMEGA ALTISE
OPERATION, MAINTENANCE
AND SAFETY INSTRUCTIONS
FOR OMEGA ALTISE TOWER FAN
MODELS INCLUDE:
OT99B

OMEGA ALTISE
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT: Read the safety precautions of this booklet carefully before attempting to assemble, install,
operate or maintain the product described. Protect yourself and others by observing all safety
information. Failure to comply with instructions could result in personal injury and/or property
damage. If you are unsure about anything regarding your fan or these instructions, please
contact Omega Altise on 1300 795 572 in Australia or [phone] in New Zealand before
operating your appliance.
1. Read all instructions carefully before using the tower fan.
2. Use this tower fan only as described in this manual. Any other use not recommended by the manufacturer may
cause fire, electrical shock, or injury to persons. Do not modify this appliance. Do not try to repair this appliance
– there are no user serviceable parts within.
3. Remove the packaging and ensure that the appliance is undamaged (keep packing box for later storage). In
case of doubt do not use the appliance and contact Omega Altise Service. Do not let children play with any parts
of the packaging.
4. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience or knowledge, unless they have been given supervision or instruction concerning
the use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they
do not play with the appliance. Extreme caution is necessary when the tower fan is used by or near children or
individuals with decreased mental and physical capacity and whenever the tower fan is left operating unattended.
5. Before you use the appliance, check if the voltage marked on the rating label corresponds to the mains in your
home. The appliance must be connected to a grounded power supply.
6. Do not use this appliance with a programmer, timer or any other device that switches the appliance on
automatically, since a fire risk exists if the appliance is covered or positioned incorrectly.
7. Do not pull the power cord to disconnect with the power source. Always grasp the plug to pull it out.
8. Do not run power cords under rugs, curtains or other combustible materials. Do not place power cords in areas
where they can be a tripping hazard. Do not operate directly below a power outlet.
9. Do not insert any objects into the appliance as it may cause an electric shock or fire or damage to the appliance. Do
not block or tamper with the appliance in any manner while it is in operation. To prevent a possible fire, do not
cover the appliance in any manner. Do not place on soft surfaces, like a bed, where openings may become
blocked.
10. Do not leave the appliance unattended. Always unplug the appliance when not in use. Take care that it is not
obstructed when oscillating.
WARNING:
The Function Switch should not be used as the sole means of disconnecting power. Always
unplug the power cord before servicing or moving the appliance.
11. Keep materials such as hair, net curtains, tablecloths & clothes away from the openings of the tower fan, as material
may be sucked into the appliance causing injury, damage to property or the appliance.
12. The appliance has hot and arcing or sparking parts inside. It must NOT be used in potentially dangerous locations
such as flammable, explosive, chemical-laden, corrosive, salty or wet atmospheres. This appliance is intended for
general indoor domestic use ONLY.
13. This appliance is not intended for use in wet or damp locations. Never locate it where it may fall into a bathtub or
other water container.
14. Do not use the tower fan outdoors. Do not use close to windows or in direct sunlight.
15. Always place the appliance on flat, stable surfaces before use. Always place the appliance vertically on its base.
16. NOTE that over time, the grills at the front and rear of the appliance will build up dust & dirt. This should be
cleaned regularly to maintain optimum efficiency. Follow the cleaning procedure within this instruction.
WARNING:
To avoid danger of electric shock, unplug from outlet when not in use and before cleaning. If the
supply cord is damaged, it must be replaced by the manufacturer, its Service Agent or similarly
qualified persons in order to avoid a hazard.In order to avoid overheating, do not cover the
appliance. Do not use the appliance in the immediate surrounding of a bath, shower or
swimming pool.
2

OMEGA ALTISE
TECHNICAL DETAILS
Model: OT99B - Black Tower fan.
Power: 220-240V 50Hz, 40W.
Weight: 4.6kg.
Dimensions (HxWxD): 986x256x301mm
GENERAL TOWER FAN PARTS
GETTING STARTED
1. Carefully remove the appliance from the plastic bag and the carton, and unwind the cord to its full length.
2. Assemble the base of the fan
4. Plug the cord set into a 220-240V~A.C. 50Hz earthed electrical outlet. Turn the power on at the electrical outlet.
Note: The remote control uses 2 batteries type AAA. To replace, remove the remote control rear cover, remove and replace old
batteries and replace the cover. When not in use, the remote control can be stored in the slot at the top rear of the appliance
body.
The airflow angle can be adjusted by 6° or 12° by inclining the fan body on the base.
Control panel
Air outlet
Air inlet (rear)
Base
Non-removable
rear cover
Handle
Control panel
Display

OMEGA ALTISE
CONTROLS
CONTROLS:
There are 5 control buttons on the control panel (top of tower fan body) and the remote control. From left to right:
A) On/Speed/Off button: Press once to turn the tower fan on (Auto, or last setting). Press again to cycle through fan speed
(Low, Medium, High) and then off. For the remote control, this is split between an On/Off button and a Speed button. This
is shown on the left-hand side of the display.
B) Temperature button: Only on the main control panel. This sets a temperature point for the Auto function. Press to cycle
through a temperature range of 15°C to 32°C. When the fan is using the Auto speed function, the fan speed will be high
when the ambient temperature is 2 or more degrees higher than the set temperature, or low when the ambient
temperature is 2 or more degrees lower than the set temperature. This does not affect the other speed functions. The
ambient temperature and set temperatures are shown at the top of the display.
C) Oscillation button: Press the oscillation button to start or stop the tower fan from oscillating. This is shown on the bottom
right-hand corner of the display.
D) Timer button: This is used to stop the tower fan at a later time. Press the timer button to increase the time by 0.5 hours
from 0.5hr-7.5hr, 0hr. The remaining time is shown in place of the set temperature on the display. When the time has
expired, the tower fan will turn off. To turn off the timer, either adjust the time to 0, or remove from the power source for
a few minutes (turning the tower fan off and on does not reset the timer; it will continue from where it left off).
E) Mode button: There are 3 possible fan modes to choose from. Press to cycle through.
1) Normal Mode: Speed is constant.
2) Natural Mode: Fan speed varies, mimicking a natural wind blowing.
3) Sleep Mode: Fan speed slows down at hourly intervals from the original set speed to low.
These are shown at the centre bottom of the display (in order from left to right).
OPERATING THE TOWER FAN:
With the power cord plugged in, it is time to turn the tower fan on by pressing the On/Speed/Off button once.
a) Choose a fan speed by pressing the On/Speed/Off button (adjust the set temperature if using the Auto function).
b) If required, turn on the oscillation with the oscillation button.
c) If required, set up the timer by pressing the timer button (a sequence of 0-7.5 hours).
d) If required, adjust the fan mode by pressing the mode button to cycle through normal, natural and sleep modes.
Turn the tower fan off by pressing the On/Speed/Off button until it cycles through to Off.
Pressing the mode button for 3 seconds will turn off the display backlight (dark mode). The backlight will turn on for 3 minutes
after a button is pressed and then turn off again. To cancel the dark mode, press the mode button again for 3 seconds.
CLEANING & MAINTENANCE
WARNING: ALWAYS UNPLUG THE CORD BEFORE MOVING OR SERVICING, DO NOT
IMMERSE APPLIANCE IN WATER!
The fan should be cleaned periodically (at least once a month depending on the build-up of dust).
Clean the body of the tower fan with a soft damp cloth. Always make sure that the appliance is completely dry before
connecting back to the mains supply.
CAUTION: Do not use gasoline, benzene, thinner, harsh cleaners, etc. as they will damage the tower fan. NEVER use
ALCOHOL OR SOLVENTS.
Vacuum the grills at the front and rear of the appliance. Do not disassemble the fan in any manner.
STORAGE: Store the tower fan with these instructions in the original packaging, in a cool, dry place.
It is important that you retain these instructions, proof of purchase as well as other important
documents about this product for future reference. Due to continual product development,
Omega Altise reserves the right to alter specifications or appearances without notice.
Dispose of packaging responsibly – recycle where facilities are available.
A division of Shriro Australia Pty Ltd
104 Vanessa St Kingsgrove NSW 2208
In Australia: 1300 795 572
In New Zealand: [phone]
www.omegaaltise.com
IM Ref: OT99B 04/2018/07