Omega Altise AP40WA User manual

Instruction
Manual
AP40WA
40cm Pedestal Fan

omega altise
2
Important Safety Instructions
1. Read all instructions.
2. Disconnect the power plug before dismantling, assembling or before cleaning.
3. Avoid touching mobile parts of the fan.
4. Make sure the fan is on a dry and even surface.
5. Never insert fingers, pencils or any other objects through the guards whenever
the power plug is connected, especially while running.
6. The appliance is not intended for use by young children or infirm persons unless
they have been adequately supervised by a responsible person to ensure that
they can use the appliance safely.
7. Young children or infirm persons should be supervised to ensure that they do not
play with the appliance.
8. Do not use the appliance for any other purpose than its intended use.
9. The fan must not be used if the guards are not fastened according to
instructions.
10. When the power cord is damaged, it must be replaced by the manufacturer or its
service agent or a similarly qualified person in order to avoid a hazard.
11. Do not use your appliance with an extension cord unless it has been checked
and tested by a qualified electrician or electrical supplier.
Read all instructions before using this unit. Keep them for future reference.
Specifications
Model AP40WA Settings 3 speed
Rated Voltage 220-240V / 50Hz Fan blade size 40cm
Watts 40W Tilt action Tilting fan head
Dimensions (cm) 42.5 x 12.5 x 53.5cm Oscillation Oscillating fan head
Controls Push Button Warranty 2 year replacement

omega altise
3
Assembly Instructions
Your pedestal fan has been boxed unassembled to minimise packaging waste. Each
part is designed to fit together and be disassembled easily for cleaning or storage.
Assemble the base to the support pole using the fasteners provided.
Loosen the height adjustment ring and extend the support pole to your desired
height.
Put the base cover over the cross base.
Retighten the height adjustment ring to prevent slipping, then place the fan assembly
onto the pole and tighten the pole screw manually.
To assemble the safety grille and blade assembly, remove the spinner (by turning it
clockwise), then the locking nut (by turning it anticlockwise) from the motor spindle.
Place the back safety grille into position. Ensure the safety grille fits onto the locating
lugs (Fig.1). If this is done correctly, the safety grille’s carry handle will be at the top.

omega altise
4
ASSEMBLY OF YOUR PEDESTAL FAN FOR ROUND BASE
Loosen the height adjustment ring and extend the support pole.
Initially the support pole will be held tightly in place. If necessary, use a pair of pliers
to grasp the support pole and pull it into position.
To assemble the safety grille and blade assembly, remove the spinner (by turning it
clockwise), then the locking nut (by turning it anticlockwise) from the motor spindle.
Operating Instructions
Remove the cable tie and unravel the cordset before operation.
The fan and motor assembly are attached to a 3-position ratchet. Tilt up or down
until the assembly clicks into the desired position.
Press speed button to adjust between low-medium-high settings.
Press button 1 for a low speed
2 for a medium speed and
3 for a high speed
Press 0 to switch the Pedestal Fan off.

omega altise
5
Care and Maintenance
1. Always disconnect the cord from the electrical outlet when cleaning your fan.
2. Light accumulated dust may be removed from the fan with a soft cloth or vacuum
cleaner using the dusting brush attachment.
3. Wipe the exterior surfaces of the fan occasionally with a cloth moistened (not
dripping wet) with a mild soap solution. Dry the case thoroughly with a soft dry
cloth before operating the fan.
4. Avoid the use of gasoline, benzine, thinner etc as they may result in damage to
the fan.
5. Store the fan in a clean dry place when not in use.
CAUTION! Do not immerse the fan in water or allow water to drip into
the interior of the fan housing as this could create a fire or electric
shock hazard.
WARNING! Do not attempt to open or repair the fan yourself. Doing so
could void the warranty and cause damage or personal injury.
Omega Altise products are distributed in Australia by Hagemeyer Appliances,
(A Division of Hagemeyer Brands Australia Pty Ltd)
ABN 28 001 375 686
Locked Bag 4013, Kingsgrove NSW 2208
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Web: hagemeyerappliances.com.au