Omega Altise OT10 User manual

OT10
Tower Fan
Instruction
Manual

omega altise
2
Important Safety Instructions
1. Read all instructions.
2. Disconnect the power plug before dismantling, assembling or before cleaning.
3. Avoid touching mobile parts of the unit.
4. Make sure the fan is on a dry and even surface.
5. Never insert fingers, pencils or any other objects through the guards whenever
the power plug is connected, especially while running.
6. The appliance is not intended for use by young children or infirm persons unless
they have been adequately supervised by a responsible person to ensure that
they can use the appliance safely.
7. Young children or infirm persons should be supervised to ensure that they do not
play with the appliance.
8. Do not use the appliance for any other purpose than its intended use.
9. The fan must not be used if the guards are not fastened according to
instructions.
10. When the power cord is damaged, it must be replaced by the manufacturer or its
service agent or a similarly qualified person in order to avoid a hazard.
11. Do not use your appliance with an extension cord unless it has been checked
and tested by a qualified electrician or electrical supplier.
Read all instructions before using this unit. Keep them for future reference.
Specifications
Model OT10 Controls Manual, Timer-off
Rated Voltage 220-240V / 50Hz Settings 3 speed
Watts 50W Oscillation Yes
Dimensions
(h x w x d) mm 750 x 240 x 270 Warranty 2 year replacement
Weight 4.2kg

omega altise
3
Parts List
1. Timer switch
2. Speed adjustment and
oscillation switches
3. Tower body
4. Base
Assembly Instructions
1. Remove all items of packaging from the tower fan.
2. Remove the fastening screws and the
screws in the cord restraint clamp from the
base sections and put to one side.
3. Turn the tower body upside down and
position the rear base (B) onto the support
posts.
4. Position the front base (A) over the support
posts on the rear base (B) and push down
fitting the bases together.
5. Secure the base with the
fastening screws.
6. Position the power cord into the
cord track and secure with the
cord restraint clamp and
screws.
7. Turn the tower fan back to an
upright position. It is now ready
for use.
Operating Instructions
1. Use in a dry place, free of excessive humidity and water.
2. This unit is operated by the manual control panel on the fan.

omega altise
4
SPEED ADJUSTMENT: Press down the desired speed switch to start/stop the fan
and to select a fan speed.
0 – OFF 1 – LOW 2 – MEDIUM 3 – HIGH
TIMER: Turn the timer knob clockwise to the
desired position to operate the timer (up to
120mins). The tower fan will automatically stop
once the set time has elapsed.
OSCILLATION: Press the oscillation switch down
to allow the tower fan to being oscillating. Press the
button again to keep the tower fan stationary.
Care and Maintenance
1. Always disconnect the cord from the electrical outlet when cleaning your fan.
2. Light accumulated dust may be removed from the fan with a soft cloth or vacuum
cleaner using the dusting brush attachment.
3. Wipe the exterior surfaces of the fan occasionally with a cloth moistened (not
dripping wet) with a mild soap solution. Dry the case thoroughly with a soft dry
cloth before operating the fan.
4. Avoid the use of gasoline, benzine, thinner etc as they may result in damage to
the fan.
5. Store the fan in a clean dry place when not in use.
CAUTION! Do not immerse the fan in water or allow water to drip into
the interior of the fan housing as this could create a fire or electric
shock hazard.
WARNING! Do not attempt to open or repair the fan yourself. Doing so
could void the warranty and cause damage or personal injury.
Omega Altise products are distributed in Australia by MEA,
(A Division of Hagemeyer Brands Australia Pty Ltd)
ABN 28 001 375 686
Locked Bag 4013, Kingsgrove NSW 2208
Phone: [phone]
Fax: [phone]
Email: [email protected]
Web: meaappliances.com.au