Omega Altise OT102TW User manual

1
O
OT102TW
Towe
r Fan
With Remote Control

2
1. Read all instructions carefully and keep this manual for future reference.
2. To avoid electric shock, do not place the cord, the plug or the appliance in water or other li uids.
3. Close supervision is necessary when the appliance is being used by or near children.
4. Disconnect the fan when not in use and before cleaning.
5. Do not place the fan on an unsteady or uneven surfaces
6. Do not insert fingers or another objects into the fan during operation
7. Do not spray any products such as bug spray into the fan.
8. The appliance is for household use only. Do not use outdoors or for any commercial or industrial
purpose.
9. This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
10. Children should be supervised to ensure that they do not play with the appliance.
11. Always disconnect the mains power, before any maintenance.
12. If the power cord is damaged, it must be replaced by the manufacturer, its service agent or a similar
ualified person in order to avoid a hazard.
13. Please ensure that the fan is switched off from the supply mains before removing the guard.
14. Do not use the appliance for any other purpose than it’s intended use
15. The unit should be used under the rated voltage and rated fre uency indicated.
IMPORTANT SAFETY INSTRUCTIONS

3
1. Remove all items of packaging from the tower fan.
2. Pass the power cord through the middle of the two base pieces.
3. Position base piece onto the support posts of the other base piece to create the base assembly.
4. Turn the tower body upside down position the base assembly onto the pedestal tube. Ensure that the
pedestal tube is sitting flush in the base assembly.
5. Screw the base assembly onto the pedestal tube with the supplied screws.
6. Position the power cord into the provided cord track in the rear base.
7. Turn the tower fan back to an upright position. It is now ready for use.
Battery Installation
One CR2032 3V battery is provided with the remote control. Please insert the battery into the remote
control on the direction of the polarity. If you are not using the fan for a long period, please remove the
battery from the remote control.
Remote control panel
INSTALLATION INSTRUCTIONS
FAN OPERATION
ON
SPEED
MODE TIMER
SWING OFF

4
Fan display panel
Button control panel
Attention:
Before connecting the power, please read this manual carefully and make sure the voltage matches the
unit’s rating re uest before use (Rated Electric Power: 220V-240V~; 50 Hz).
The fan will issue "two beeps" when first switched on at the power socket. The fan will then go into standby
mode and can be powered on by pressing the ON/Speed button.
ON/SPEED
Press ON/SPEED to switch on the fan.
Press ON/SPEED button again to adjust the speed of the fan. The speed settings are as Follows: Low
Medium High Low ，repeating.
T MER
Press the T MER button to activate the Timer-Off function on the fan. Each time the T MER button is
pressed the LED will display 1H (1 Hour) 2H (2 Hours) 4H (4 Hours) 8H (8 Hours), repeating. The unit
will then go into standby mode after the timer has finished.
Low Speed
Medium Speed
High Speed
Natural Mode
Sleep Mode
Timer Swing
Remote Sensor
Power Indicator
Ion Power Indicator

5
MODE
Normal Nature Sleep , repeating and the LED will show the mode type accordingly.
NORMAL: The fan will run at constant speed.
NATURAL: The fan will cycle through high-mid-low, and repeat automatically.
SLEEP: The fan switches ON and OFF at set speeds saving energy during the night.
If the fan speed is set to High, the fan will operate for 30 minutes in each fan speed setting. The cycle will
continue until the preset timer setting is reached or the unit is turned off.
If the fan speed is set to Medium, the fan will operate for 30 minutes in Medium and then switch to Low
speed and will operate for 30 minutes then switch back to Medium and the cycle continues until the preset
timer setting is reached or the unit is turned off.
If the fan is set to Low speed setting the fan will continue to operate in low setting until the preset timer
setting is reached or the unit is turned off.
SW NG
Press “Swing” once: the fan will swing horizontally and will light up. Press “Swing” again and the fan will
not “Swing”.
OFF
Press “Off” to put the fan into Standby mode.
CLEANING AND MAINTENANCE
1Before you clean the fan, you must disconnect the fan from the mains power.
2Rub the stand pole with clean cloth.
3Store the fan in a cool dry place when not in use.
4Clean the back cover once a week with a vacuum cleaner.
5Caution: Do not immerse the fan in water or allow water to drip into the interior
as this may create a fire or electric shock hazard.
6Caution: Do no attempt to open or repair the fan yourself. Doing so could
void the warranty and cause damage or personal injury.

6
TECHNICAL SPECIFICATIONS
Rated voltage 220-240V~
Rated Fre uency 50Hz
Rated power 65W
Net weight 3.5kg
Gross weight of the box 6.0kg
Noise ≤55dB
Product size 1005.5×290.2×290.2mm
Suitable environment 0～+40°C, relative humidity 90%