Omega Lift Equipment 21260AA Instructions for use

WORKING LOAD LIMIT 2600KG
HEAVY DUTY LOW PROFILE
GARAGE SERVICE JACK
THIS JACK CONFORMS TO MANDATORY STANDARD AS 2615:2016
Model No: 21260AA
Imported by:
SHINN FU AUSTRALIA PTY. LTD.
15 Viewtech Place, Rowville 3178 VIC Australia PRINTED IN CHINA
21260AA-M0_032020
Operating Instructions & Parts Manual
READ RULES FOR SAFE OPERATION AND INSTRUCTIONS CAREFULLY
WARNING: THE JACK MUST BE USED ONLY ON HARD LEVEL
SURFACES AND BE FREE TO ROLL DURING LIFTING AND LOWERING.
DO NOT GET UNDER A VEHICLE THAT IS SUPPORTED BY A TROLLEY
JACK - USE THIS HYDRAULIC TROLLEY JACK WITH SUITABLY RATED
VEHICLE SUPPORT STANDS.

2
SAFETY INSTRUCTIONS
INSPECTIONS
1. BEFORE EACH USE
Visual inspection should be made before each use of the trolley jack for abnormal conditions such
as cracked welds, leaks and damaged, loose, or missing parts.
2. AFTER EACH USE
Trolley jack should be inspected immediately if the lift is believed to have been subjected to
an abnormal load or shock. It is recommended that inspection be made by manufacturer’s or
supplier’s authorised repair facility.
3. ANNUAL INSPECTION
Annual inspection of the trolley jack is recommended and is recommended to be made by the
manufacturer’s or supplier’s authorised repair facility to ensure that your trolley jack is in optimum
condition.
RECOMMENDATION FOR SAFE USAGE OF THE JACK
1. Consult the vehicle manufacturer’s manual prior to the lifting of the vehicle.
2. Conduct a pre-operational check of the equipment.
3. Use the hydraulic trolley jack for lifting and lowering only; the raised vehicle should be supported
on suitably rated vehicle support stands.
4. Use the hydraulic trolley jack on a hard level surface and ensure it is free to roll during lifting and
lowering.
5. No person should remain in a vehicle that is being lifted.
6. Chock the unlifted wheels of the vehicle.
7. Centrally locate the load on the head cap.
8. Support the vehicle on suitably rated vehicle support stands and remove the hydraulic trolley jack
prior to commencement of work on the vehicle.
9. No person should get bodily under a vehicle that is supported only by a hydraulic trolley jack.
10.Make sure that lift point is stable and properly centered on jack saddle.
11. Vehicle should be clear of all passengers. Transmission should be in gear (or park for automation
transmission) and the emergency brake should be engaged.
12.Familiarize yourself thoroughly with this owner manual before operation to prevent damage to
jack and property, or personal injury.
Modications: Modications must not be carried out or accessories added.

3
SAFETY INSTRUCTIONS
CAUTION BEFORE USE
Due to shipment and/or handling air can be trapped in the hydraulic system, which can interfere with
the jacks lifting. To release air from the hydraulic system:
• Open release valve by turning the jack handle counterclockwise.
• Remove the oil ller plug from the cylinder.
• Rapidly pump jack handle through several full strokes.
• Replace the oil ller plug into the cylinder.
WARNING
DEATH OR
INJURY FROM
INCORRECT USE
USE TWO
SUPPORT
STANDS
FLAT HARD
LEVEL GROUND
FREE TO ROLL
DURING LIFTING
AND LOWERING
REFER TO VEHICLE MANUFACTURER’S
MANUAL FOR INSTRUCTIONS

4
OPERATIONS
MAINTENANCE
TO RAISE:
Place vehicle in park, apply brake and chock wheels with suitable
devices.
1. Position the jack under the load and close release valve by
turning clockwise rmly.
2. Operate manually by pumping with handle until saddle
ALMOST contacts with vehicle. Check to see that the saddle is
centred and will contact the load lifting point rmly.
3. Continue to pump jack handle until load is raised to desired
height and immediately transfer load to appropriately rated
jack stands.
TO LOWER:
1. Raise load sufciently to remove support devices, then slowly
turn handle counterclockwise until load begins to lower.
Carefully control the rate of descent and avoid shock load
created by opening and closing valve quickly. This may result
in overloading hydraulic circuit causing damage to jack and
personal injury.
2. Remove jack from under load and if necessary, push handle
sleeve and saddle down fully to reduce piston and ram
exposure to contamination.
MAINTAINING OIL LEVEL
Important: When adding or replacing oil, ALWAYS use good grade
Hydraulic Jack oil. DO NOT use Hydraulic Brake Fluid, Alcohol,
Glycerin, Detergent, Motor Oil or dirty oil. Use of an improper uid
can cause serious internal damage to your jack.
ADDING OIL
• Position the jack on level ground and fully lower the saddle.
Remove oil filler plug.
• Turn jack over and drain old oil out through the oil filler plug hole.
• Refill with new oil through the oil filler plug hole. Not allow dirt or
other foreign materials to enter the hydraulic system when filling.
• After refilling, remove any air from hydraulic system by opening the
release valve and rapidly pumping the jack handle several times.
• Put the oil filler plug back and the jack is ready for use.
LUBRICATION
• Add lubricating oil to all moving part as needed.
PREVENTING RUST
• Check ram and pump plunger every few months for any signs of
rust or corrosion. Clean as needed by wiping with oily cloth.
• When not in use, ALWAYS store jack with saddle and pump plunger
lowered all the way down.
Know Your Jack
Hydraulic Power
Unit
Handle Assembly
Handle Fork
Release Caster
Front Caster
Saddle
Know Your Jack
Pump Plunger
Reservoir
Oil Filler Plug
Reservoir
Ram
For Reference Only
OIL LEVEL: It is recommended
that the oil level is kept at
approximately 12mm below to
filler hole level of the power unit.

5
SPECIFICATION
TROUBLE SHOOTING
Model
No.
Working
Load Limit
Height
Lowered
Height
Raised
Hyd.
Lift
Handle
Length
Saddle
Dia.
Length Width Height Net
Weight
kg mm mm mm mm mm mm mm mm kg
21260AA 2,600 100 533 433 1,320 110 751 360 162 44
Symptom Possible Causes & Solutions
Jack will not lift load
1. Release valve not tightly closed. To close or tighten, turn release
valve clockwise.
2. Air is in hydraulic system. Release air from System.
3. Oil level is low in jock. Add oil as required.
4. Power unit malfunctioning. Replace the power unit.
Jack will lift load, but
not hold
1. Oil Level is low in jack. Add oil as required.
2. Power unit malfunctioning. Replace the power unit.
Jack will not lower
completely
1. Oil reservoir is over lled. Drain out some oil.
2. Lubrication of moving parts is necessary.
Poor jack lifting.
Pump feels spongy
1. Air is in hydraulic system. Release air from System.
2. Oil Level is low in jack. Add oil as required.
3. Power unit malfunctioning. Replace the power unit.
Jack can not reach
maximum height
1. Air is in hydraulic system. Release air from System.
2. Oil level is low in jock. Add oil as required.
Handle raises by itself
when jack is under
load
1. Air is in hydraulic system. Release air from System.
NOTE: If the above procedures can not remedy the problem, the product shall be taken to a local service centre
for further examination.
For Reference Only
Width
Min.
Height
Max.
Height
Height
Length

6
SPARE PARTS
30
29
8
6
1
2
3
4
5
5
37
36
38
31
32
33
34
35
40
41
42 39
43
38
45
44
46 47
81
48
45
51
45
65
64
63
62
51
50
49
69
68
67
66 94
90
92
93
95
89
87
86
85
88
19
18
23
20
20
21
21
17
16
11
9
12
13
14
10
11
9
12
13
14
17
16
24
25
15
22
20
21 21
20
23
18
91
19
21
28
21
27
26
21
58
59
60
61
57
56
55
54
53
52
77
78
79 80
70
71
72
71
72
73
74
75
76
45 83
82
84
4
78

7
SPARE PARTS
Item # Description Qty
1 Saddle Pad 1
2 Saddle Blot 1
3 Saddle 1
4 Radius Link 2
5 Snap Ring 2
6Lifting Arm Assembly 1
7 Retainer 1
8 Spring 2
9 Front Wheel 2
10 Front Axle 1
11 Bering Bush 2
12 Washer 2
13 Lock Washer 2
14 Nut 2
15 Radius Link Stud 2
16 Lock Washer 2
17 Cap Nut 2
18 Right Handle Bolt 2
19 Lock Washer 2
20 Cup-head Bolt 4
21 Lock Washer 8
22 Frame Tie Rod 1
23 Nut 2
24 Left Plate Assembly 1
25 Right Plate Assembly 1
26 Bear Caster Assembly 2
27 Bearings 2
28 Cap Nut 2
29 Trestle Table 1
30 Magnetic Rubber Pad 1
31 Ram Plunger 1
32 Bushing Cover 1
33 Back-up Washer 1
34 U-cup Seal 1
35 Snap Ring 1
36 Top Nut 1
37 O-ring 1
38 Wedge Ring 2
39 Reservoir 1
40 Cylinder 1
41 Back-up Washer 1
42 O-ring 1
43 Oil Seal 1
44 Base 1
45 Ball 5
46 Washer 1
47 Throttle Valve 1
48 Spring 1
Item # Description Qty
49 Release Valve Assy 1
50 O-ring 1
51 Ball 2
52 Guard Screw 1
53 O-ring 1
54 Screw Safety Valve 1
55 Spring 1
56 Valve 1
57 Ball 1
58 Bolt 1
59 Back-up Washer 1
60 O-ring 1
61 Spring 1
62 Pump Piston 1
63 O-ring 2
64 Pump 1
65 Washer 1
66 Pump Core Rest Spring 1
67 Spring Sleeve 1
68 Spring Stop Sheet 1
69 Snap Ring 1
70 Pump Piston 1
71 Back-up Washer 2
72 O-ring 2
73 Pump 1
74 Back-up Washer 1
75 O-ring 1
76 Washer 1
77 Pump Core Rest Spring 1
78 Spring Sleeve 1
79 Spring Stop Sheet 1
80 Snap Ring 1
81 Filter 2
82 Bolt 1
83 Lock Washer 1
84 Washer 1
85 Handle Base 1
86 Pin 1
87 Roller 1
88 Snap Ring 1
89 Bolt 1
90 Handle-i 1
91 Handle Lock Button 1
92 Handle-II 1
93 Enveronmental
Protection Foam 1
94 Handle Grip 1
95 Hook 1

8
WARRANTY
1. This product is covered by an express warranty for 12 months from the date of purchase by the
original purchaser. Subject to the conditions of this warranty Shinn Fu Australia Pty Ltd or its
authorised repair agents will replace the product or perform necessary service on the product
without charge for parts or labour if the product is found to be faulty within the warranty period.
2. This warranty only applies to products imported by Shinn Fu Australia Pty Ltd and used within
Australia. Shinn Fu products imported by other importers are specically excluded.
3. This warranty only applies if the product has been used under normal conditions and in accordance
with the User Manual and that, in the opinion of Shinn Fu Australia Pty Ltd, reasonable care has
been taken of the product.
4. This warranty is void if the product has been tampered with or repaired by any unauthorised
person or has been modied in any way.
5. If a warranty service is required the purchaser should:
• Take the product to the nearest Shinn Fu Australia pty Ltd repair agent or return it to the place
of purchase.
• Provide evidence of proof of purchase and the date of purchase.
• Provide details of the problem encountered.
6. Shinn Fu Australia Pty Ltd guarantees that spare parts and repair facilities for this product will be
available for a period of ve years from the date of the last importation of the model of the product.
After that period all reasonable efforts will be made to supply spare parts but supply cannot be
guaranteed.
7. The purchaser may also have rights under the statutory warranty provisions of the Trade Practices
Act 1974 and other legislation and nothing in this express warranty is to be taken to exclude or
affect any of those rights.
IF YOU REQUIRE ANY ASSISTANCE REGARDING WARRANTY CONDITIONS PLEASE
CONTACT THE SHINN FU AUSTRALIA PTY LTD COMPLIANCE OFFICER ON [phone] OR
EMAIL: [email protected]
Imported by:
SHINN FU AUSTRALIA PTY. LTD.
15 Viewtech Place, Rowville 3178 VIC Australia