Omega Lift Equipment MagicLift 25032 Instructions for use

MagicLift™ Service Jack Combo
Model
25032
Printed in China
25032-M0 rev 11/07
Operating Instructions & Parts Manual
Read this manual and follow all the Safety Rules and Operating Instructions before using this product.
SFA Companies
http://www.omegalift.com
Capacity
3 Ton
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
!
! ADVERTENCIA
• Leer, comprender, y seguir las instrucciónes antes
de utilizar el aparato.
• El manual de instrucciónes y la información de
seguridad deben estar comunicado en lengua del
operador antes del uso.
• No seguir estas indicaciónes puede causar daños
personales o materiales.
! WARNING
To avoid crushing and related injuries:
NEVER work on, under or around a
load supported only by a hydraulic
jack. ALWAYS use adequately rated
jack stands.

2
SAFETY and GENERAL INFORMATION
Save these instructions. For your safety, read, understand, and follow the information provided with and on this
product before using. The owner and operator of this product shall have an understanding of this product and safe
operating procedures before attempting to use. The owner and operator shall be aware that use and repair of this
product may require special skills and knowledge. Instructions and safety information shall be conveyed in the
operator's native language before use of this product is authorized. If any doubt exists as to the safe and proper use
of this product, remove from service immediately.
Inspect before each use. Do not use if broken, bent, cracked or damaged parts are noted. Any jack or jack stand
that appears damaged in any way, or operates abnormally shall be removed from service immediately. If the jack or
jack stand has been or suspected to have been subjected to a shock load (a load dropped suddenly, unexpectedly
upon it), immediately discontinue use until jack has been checked by a factory authorized service center (contact
distributor or manufacturer for list of authorized service centers). It is recommended that an annual inspection be
done by qualified personnel. Labels and Operator's Manuals are available from manufacturer.
Important: Any jack stand that appears to be damaged in any way, is worn or operated abnormally shall be removed
from service and destroyed immediately. No repair shall be made to a jack stand. Replace jack stands as a matched
set. No user servicable parts are available.
PRODUCT DESCRIPTION
Service Jack is designed to lift, but not support, one end of a vehicle. Immediately after lifting, loads must be supported
by a pair of appropriately rated jack stands. This MagicLift™ Service Jack has a unique feature that provides fast,
no load lifts to the jacking point, at which time it lifts in approximately 0.75~2" increments.
NEVER use hydraulic jack as stand-alone device. After lifting, immediately support the lifted vehicle with
a pair of appropriately rated jack stands.
Jack Stands are designed to support rated capacity, partial vehicle loads consisting of one end of a vehicle. Use
as a matched pair to support one end of a vehicle only.
NEVER use automotive jack stands to support both ends or one side of a vehicle!
Use only one (1) pair per vehicle. Rated capacity is per pair only!
!
!
Figure 1 - Service Jack Components
Saddle
Front Wheel
Handle
Caster
Release
Valve
Pump
Piston
Handle Sleeve
Lifting Arm
Locking Handle
Lock Pin
Locking Pawl
(stopper)
Base Frame
Saddle
Press Tab
Figure 2 - Jack Stands Components
Ratchet Bar

SPECIFICATIONS
Service Jack:
Capacity Min.
Height
Max.
Height
Saddle
Diameter
Jack Size
(L x W x H)
Volume of Hyd.
Oil
Net
Weight
3 Ton 5 1/4" 20 7/8" 5" 27 1/8" x 13 3/8" x 6 3/4" 245mL 78 lb.
Jack Stands:
Capacity Min.
Height
Max.
Height Saddle Size Base Size (L x W)
Net
Weight
3 Ton 11 1/2" 17" 3 1/2" x 1" 6 3/4" x 7 3/4" 14.1 lb.
PREPARATION
Assembly
Make sure all parts are present (refer Fig. 1 & 2). If any parts is missing or damage, do not attempt to assemble,
install or operate the product. Contact Customer service.
A. Service Jack:
1. Attach the 2-pc handle with bolt provided on the handle.
2. Secure the assembled handle into handle sleeve with provided bolt. Tighten securely to prevent accidental
removal of handle while in use.
B. Jack Stands:
Tools required: Hammer and Punch (not included)
1. Install ratchet bar into base frame with ratchet portion of bar aligned with locking pawl.
2. Move the ratchet bar to its lowest position by raising the locking handle, thereby releasing the stopper and
guiding the bar downward.
3. Ratchet/ collar lock is accomplished by simply pressing the press tab (see Fig. 2) inward using a suitable hammer
and punch. This will effectively prevent inadvertent loss of the ratchet bar.
Before Use
1. Verify that the product and application are compatible, if in doubt call Omega Technical Service [phone].
2. Before using this product, read the operator's manual completely and familiarize yourself thoroughly with the
product, its components and recognize the hazards associated with its use.
3. Inspect before each use. Do not use if there are bent, broken or cracked components noted.
4. Always check the vehicle owner’s or service manual for location of proper lift and support points.
Service Jack:
5. To familiarize yourself with basic operation of service jack, locate and turn the release valve (handle):
a. Clockwise until firm resistance is felt to further turning. This is the ‘CLOSED’ release valve position used to
raise the saddle.
b. Counter-clockwise, but no more than 1/2 turn from the closed position. This is the ‘OPEN’ release valve
position used to lower the saddle.
6. With saddle fully lowered, remove the oil filler screw. Pump 6 to 8 full strokes. This will help release any pressurized
air which may be trapped within the reservoir. Check oil level. Proper oil level will vary from just covering the ram
cylinder to 3/16” above it as seen from the oil filler hole. Reinstall the oil filler screw.
7. Ensure that jack rolls freely. Raise and lower the unloaded saddle throughout the lifting range before putting into
service to ensure the pump operates smoothly. Replace worn or damaged parts and assemblies with Omega
authorized replacement parts only.
Bleeding / Venting Trapped Air of a Service Jack
With the release valve in the OPEN position (5b.) and with saddle fully lowered, locate and remove the oil filler
screw. Pump 6 to 8 full strokes. This will help release any pressurized air which may be trapped within the reservoir.
Reinstall the oil filler screw.
3

4
! WARNING
• Study, understand, and follow all printed
materials provided with/on this product before
use.
• Use only on hard, level surface.
• Do not exceed rated capacity.
• Lift and support only on areas of the vehicle as
specified by the vehicle manufacturer.
• Center load on saddle.
• No alterations shall be made to this product.
SERVICE JACK:
• This is a lifting device only!
• Immediately after lifting, support the load with
a pair of appropriately rated jack stands.
• Do not move or dolly the vehicle while on the
jack.
JACK STANDS:
• Rated capacity of jack stands is PER PAIR!
• Use as a matched pair to support one end of a
vehicle only. Use only ONE (1) PAIR per vehicle.
• Jack stands are not to be used to simultaneously
support both ends or one side of a vehicle.
FAILURE TO HEED THESE MARKINGS MAY
RESULT IN PERSONAL INJURY AND/OR
PROPERTY DAMAGE
To avoid crushing and related injuries:
• Never work on, under or around a load supported
only by hydraulic jack.
• Always use adequately rated jack stands.
• Chock each unlifted tire in both directions.
• Do not use this device to lift, level, lower, support
nor move a house, mobile home, travel trailer,
camper or any building structure.
• Be alert and sober when using this product. Do not
operate under the influence of drugs or alcohol.
! WARNING
X
OPERATION
Lifting
Only attachments and/or adapters supplied
by the manufacturer shall be used.
Use jack stands only on areas of the vehicle
as specified by the vehicle manufacturer. Use
ONLY on vehicles whose support points are compatible
with the saddle of the jack stand. Incompatibility may
result in structural damage to the vehicle and/or jack
stand. Structural damage to either may result in sudden
and unexpected loss of load height!
1. Follow vehicle manufacturer’s recommended
guidelines for lifting. Engage the emergency brake
and chock each unlifted wheel in both directions to
prevent inadvertent vehicle movement.
2. Set up jack stands:
a. Adjust height by pulling up the ratchet bar.
b. The weight of locking handle should secure the
ratchet bar in desired position. To confirm this,
Simply push down on the locking handle.
3. Close release valve by turning the handle clockwise until
firm resistance is felt.
4. Verify lift point, then center jack saddle under lift point.
Pump handle to contact lift point. To lift, pump handle
until load reaches desired height.
5. Transfer load immediately to a pair of jack stands:
a.Carefully position the stands so that load is
centered on the saddle. Ensure that ratchet is
secured before loading.
b.Slowly lower the vehicle onto stands. Ensure the
vehicle is secured before working on, around or
under.
NEVER use hydraulic jack as a stand alone
device! ALWAYS transfer the lifted load
IMMEDIATELY to a pair of appropriately rated jack
stands.
Lowering
Be sure all tools and personnel are clear before
lowering load. Slowly open the release valve!
The more you turn the handle counter-clockwise, the
faster the load will come down. Maintain control of the
rate of speed at which the load lowers at all times!
1. Raise vehicle high enough to clear the jack stands.
2. Remove jack stands carefully.
3. Slowly turn the handle counter-clockwise, but no more
than 1/2 full turn. If the load fails to lower:
a. Use another jack to raise the vehicle high enough
to reinstall jack stands.
b. Remove malfunctioning jack, then the jack stands.
c. Use the functioning jack to lower the vehicle
4. After removing jack from under the vehicle, fully
lower the saddle to reduce ram exposure to rust and
contamination.
!
!
!
!

MAINTENANCE
A. Service Jack:
Important: Use ONLY good grade hydraulic jack oil. Avoid mixing different types of fluid and Never use brake fluid,
turbine oil, transmission fluid, motor oil or glycerin. Improper fluid can cause failure of the jack and the potential
for sudden and immediate loss of load. We recommend Mobil DTE 13M.
Adding oil
1. With saddle fully lowered set jack in its upright, level position. Locate and remove oil filler screw.
2. Fill with oil until ~3/16" above the inner cylinder as seen from the oil filler hole. Reinstall the oil filler screw.
Changing oil
For best performance, replace the complete fluid supply at least once per year.
1. With saddle fully lowered, remove oil filler screw.
2. Lay the jack on its side and drain the fluid into a suitable container.
Note: Dispose of hydraulic fluid in accordance with local regulations.
3. Fill with oil until ~3/16" above the inner cylinder as seen from the oil filler hole. Reinstall oil filler screw.
Lubrication
A periodic coating of light lubricating oil to pivot points, axles and hinges will help to prevent rust and assure that
wheels, casters and pump assemblies move freely.
Cleaning
Periodically check pump piston and ram for signs of rust or corrosion. Clean as needed and wipe with an oily cloth .
Note: Never use sandpaper or abrasive material on these surfaces!
Storage
When not in use, store the jack with saddle fully lowered.
B. Jack Stands:
Periodically inspect each stand. Ensure all parts move freely. Do not apply oil or grease to any portion of this
product. If rust appears, sand affected area and cover with suitable utility paint. Please note that there is no
replacement part applicable to this device.
Storage
Store stands in upright position and in a clean, dry area.
5
TROUBLESHOOTING
Symptom Possible Causes Corrective Action
Jack will not lift load • Release valve not tightly closed
• Load is too heavy
• Ensure release valve tightly closed
• Consider higher capacity jack
Jack will lift, but not maintain
pressure
• Release valve not tightly closed
• Hydraulic unit malfunction
• Ensure release valve tightly closed
• Discontinue use, contact Omega
technical service
Jack will not lower after unloading • Reservoir overfilled
• Linkages binding
• Fluid level low
• Drain fluid to proper level
• Clean and lubricate moving parts
• Ensure proper fluid level
Poor lift performance • Fluid level low
• Air trapped in system
• Ensure proper fluid level
• With ram fully retracted, remove oil
filler screw to let pressurized air
escape. Reinstall oil filler screw
Will not lift to full extension • Fluid level low • Ensure proper fluid level

6
Figure 3 - Replacement Parts Illustration for Model 25032 Service Jack Combo
REPLACEMENT PARTS
Not all components of the jack are replacement items, but are illustrated as a convenient reference of location and
position in the assembly sequence. When ordering parts, please give the Model number, part number and parts
description. Call or write for current pricing: SFA Companies 10939 N. Pomona Ave. Kansas City, MO 64153, U.S.A.
E-Mail: [email protected] Tel: [phone] Fax: [phone] Website: http://www.omegalift.com
A
A
B
B
C
CD
E
F
G
H
I
K
J
L
N
M
M
NO
1
2
21
3
4
5
6
7
8
9
10
11 12
13
14
15
24
16
17
16
18
19
20
22
23
26

7
Replacement Parts List for model 25032 Service Jack
Seal Kit G43000-0000 includes:
Item Part No. Description Qty
1 A20060-0002 Filler Screw 1
2 G48900-0023 Pump Piston 1
3 G48900-0004 Release Valve 1
4 G43000-0002 Grease Fitting Nipple, M6 1
5 G59508-0004 Saddle 1
6 G62000-1003 Return Spring 2
7 G58900-0002 Handle Sleeve 1
8 G48900-0015 Pin, f13 1
9 G59305-0003 Nut M10 1
10 G48900-0016 Release Valve Gear 1
11 G59305-0005 Lock Washer f10 1
12 G48900-0024 Bolt M10x16mm 1
13 G48900-0017 Release Valve Connecting Bar 1
14 G59305-0007 E-ring f15 2
15 G59305-0004 Washer f18 2
16 G59305-0006 Lock Washer f20 2
17 G48900-0018 Handle Bolt, Left 1
18 G48900-0019 Bolt M12 4
19 G48900-0020 Handle Bolt, Right 1
20 G48900-0001 Return Spring, Handle Sleeve 1
21 G43000-0001 Hydraulic Power Unit 1
22 G48900-0003 Handle Assembly 1
23 G69300-0003 Caster Assembly 2
24 G48900-0007 Front Wheel Assembly 2
25 G43000-0000 Seal Kit (includes # A ~ O) -
26 32035 Jack Stands, 3 Ton (replace as pair) 1
27 25032-L0 Label(s) -
28 25032-M0 Manual -
Item Description Qty.
AO-ring, f63.5x2.8 2
B O-ring 2
C Back-up Washer 2
D Back-up Washer 1
E U-cup 1
F Back-up Washer 1
GO-ring, f44.5x2.5 1
H Back-up Washer 1
IO-ring, f38x3.5 1
JO-ring, f19x2.4 1
K Back-up Washer 1
L ** O-ring, f8.2x2.4 1
M ** O-ring 2
N ** Back-up Washer 2
OO-ring, f15x2.4 1
(**) Replacement requires special skills,
knowledge, and equipment. Only an
authorized service center may perform
the repair and/or replacement of
these items. Contact Omega technical
service for list of service centers.

ONE YEAR LIMITED WARRANTY
For a period of one (1) year from date of purchase, SFA Companies will repair or replace, at its option,
without charge, any of its products which fails due to a defect in material or workmanship under normal usage. This
limited warranty is a consumer's exclusive remedy.
Performance of any obligation under this warranty may be obtained by returning the warranted product, freight
prepaid, to SFA Companies Warranty Service Department, 10939 N. Pomona Ave., Kansas City, MO 64153.
Except where such limitations and exclusions are specifically prohibited by applicable law, (1) THE
CONSUMER'S SOLE AND EXCLUSIVE REMEDY SHALL BE THE REPAIR OR REPLACEMENT OF DEFECTIVE
PRODUCTS AS DESCRIBED ABOVE. (2) SFA Companies SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL
OR INCIDENTAL DAMAGE OR LOSS WHATSOEVER. (3) ANY IMPLIED WARRANTIES, INCLUDING WITHOUT
LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, SHALL BE LIMITED TO ONE YEAR, OTHERWISE THE REPAIR, REPLACEMENT OR REFUND AS
PROVIDED UNDER THIS EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER,
AND IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. (4) ANY MODIFICATION,
ALTERATION, ABUSE, UNAUTHORIZED SERVICE OR ORNAMENTAL DESIGN VOIDS THIS WARRANTY AND
IS NOT COVERED BY THIS WARRANTY.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not
apply to you. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also
have other rights, which vary from state to state.
SFA Companies
10939 N. Pomona Ave. Kansas City, MO 64153
888-332-6419
[email protected]
8