Omix-Ada 11704.05 User manual

460 HORIZON DR. SUITE 400 | SUWANEE, GA 30024 | PHONE: [phone] | FAX: [phone] | [email protected]
Roof Top Tent
OMIX-ADA®TECHNICAL SUPPORT
PHONE: M-F 8am - 5pm EST 1-800-449-6649 | EMAIL: [email protected]
FOR WARRANTY INFORMATION VISIT: www.Omix-Ada.com
Components
Page 1/6
Part # 11704.05
2. Window Rod..................................................(8)
3. Aluminum Rails..............................................(2)
4. Ladder Mounting Bracket............................(2)
5. Ladder............................................................(1)
6. Slide Plate......................................................(8)
7. Base Plate......................................................(4)
8. M8 x 55mm Bolt.............................................(8)
9. M8 Flat Washer..............................................(8)
10. M8 Nylock Nut...............................................(8)
11. M6 x 40mm Hex Bolt......................................(8)
12. M6 x 18mm Hex Bolt.......................................(2)
13. M6 Flat Washer..............................................(16)
14. M6 Nylock Nut...............................................(10)
15. M6 Plastic Washer..........................................(4)
16. Shoe Bag........................................................(1)
17. Tent Cover......................................................(1)
1. Roof Top Tent................................................(1)
This Roof Top Tent is designed to mount on most OE and aftermarket roof rack/crossbar systems. Consult your
owner's manual for weight restrictions.
Place tent and tent base with holes face up on a clean, protected surface. Slightly open up tent, open up
entrance and remove all parts from the interior of the
tent.
Direction of Opening
Before you fit your new Roof Top Tent to your vehicle, determine which side of the vehicle you want your tent to
open. Read instructions thoroughly before assembling and installing this product. Product may vary from image.
Periodically check torque of all hardware.

460 HORIZON DR. SUITE 400 | SUWANEE, GA 30024 | PHONE: [phone] | FAX: [phone] | [email protected]
Roof Top Tent
Page 2/6
2. Attach ladder brackets to the base of the
tent using M6 bolts. Bolt each ladder
bracket to the base of the tent through
the pre-drilled holes.
3. Mount the ladder brackets to the ladder
using the supplied M6 bolts, washers, plastic
washers, and nut. Plastic washers will go on
both sides of the bracket on the ladder. Do not
over tighten bolts, there should be a slight
resistance when rotating the ladder.
Tech Tip: Thread locker is recommended for
these bolts as an extra measure for vibration
resistance.
1. Lay the tent on its side on the ground. Using
the supplied M6 bolts and washers, lift the
mattress and insert the bolts into the pre-drilled
holes. Align the aluminum rails with the
previously installed M6 bolts through the floor.
Slide the M6 nuts into the track and tighten the
bolts from inside the tent. Do not over tighten
hardware.
Tech Tip: We recommend using a blanket or
tarp when placing the tent on the ground to
keep the tent clean.
M6 Bolt
Washer
Tent Base
M6 Nylock Nut
Aluminum Rails
The Aluminum Rails fitted to the base of the Roof Top
Tent with the slide plate and bolt fitted.

460 HORIZON DR. SUITE 400 | SUWANEE, GA 30024 | PHONE: [phone] | FAX: [phone] | [email protected]
Roof Top Tent
Page 3/6
5. Secure the rooftop tent to your roof rack or roof
bars. Use 2 M8 bolts and 2 slide plates with the
base plate to secure the bar. If the cross bars are
too far apart the center will not be properly
supported and may be damaged.
Do not over tighten nuts because this will cause
the bolt head to strip the aluminum slide plate.
Periodically check torque of all hardware.
6. Release the hook and loop straps on all
sides of the tent.
4. With help, carefully lift the tent onto the
vehicle. Insert M8 bolts into the slide plate. Slide
the plate and bolt into the aluminum rails. Bolts
should be located on either side of the cross
bars. Slide two plates from the rear and one
from the front, ensuring there are 4 per rail
when complete.

460 HORIZON DR. SUITE 400 | SUWANEE, GA 30024 | PHONE: [phone] | FAX: [phone] | [email protected]
Roof Top Tent
Page 4/6
8. Use the ladder as leverage to open the tent,
carefully folding it to the open position.
9. Allow the ladder to rest on the ground. If the
ladder is extended too far it will need to be
adjusted. (See next step) The ladder should be at
a slight angle so it can support the tent while
open.
7. Carefully extend the ladder until it clicks into
place. Springs should engage.

460 HORIZON DR. SUITE 400 | SUWANEE, GA 30024 | PHONE: [phone] | FAX: [phone] | [email protected]
Roof Top Tent
Page 5/6
11. To lock the knobs into the open position, pull
the knob up and turn it 1/4 turn. To unlock, turn
another 1/4 turn. This will engage the spring.
12. To install the tent flap rods, locate the slots on
the base of the tent flap and insert the rods into
the pre-drilled holes. Ensure the rods are inserted
completely.
10. The ladder features several adjustment holes.
Additional holes may be drilled if needed. Do not
drill holes below the bottom pre-drilled hole.
Tech Tip: Use a 3/8” drill bit to drill new adjustment
holes.
Bottom-most pre-drilled hole
Spring-loaded locking position
Unlocked raised
position

460 HORIZON DR. SUITE 400 | SUWANEE, GA 30024 | PHONE: [phone] | FAX: [phone] | [email protected]
Roof Top Tent
Page 6/6
13. Place the hook end of the rod through the
grommet on rain/shade cover with the hook
part facing outward and downward.
Storage and Handling Guidelines Cautions
- Do not store the tent wet.
-Adding a tent increases the height of your vehicle and alters its center of gravity. Use
caution.
-Periodically ensure all nuts and bolts are attached and are tight. Failure to follow these
instructions will void the warranty.
Care Instructions
Clean only with cold water and a soft brush - do not use soap or detergent, this will
remove the waterproofing compounds.
Do not expose to petrol, oil or solvents.