Omron M6 Comfort User manual

Digital Automatic Blood Pressure Monitor
Model M6 Comfort
• Instruction Manual
• Mode d’emploi
• Gebrauchsanweisung
• Manuale di istruzioni
• Manual de instrucciones
• Gebruiksaanwijzing
• РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ
IM-HEM-7000-E-01-05/06
EN
FR
DE
IT
ES
NL
RU
HEM-7000 main.book Page 1 Monday, June 19, 2006 8:53 AM

2
Contents
Introduction ..............................................................................3
Important Safety Information ..................................................4
1. Overview ..............................................................................5
2. Preparation ..........................................................................7
2.1 Installing/Replacing the Batteries.....................................7
2.2 Setting the Date and Time ...............................................8
3. Using the Unit....................................................................10
3.1 How to Sit Correctly When Taking a Measurement .......10
3.2 Applying the Arm Cuff ....................................................12
3.3 Taking a Reading...........................................................15
3.4 Instructions for Special Conditions.................................18
3.5 Using the Memory Function ...........................................19
4. Quick Reference Guide.....................................................21
5. Handling Errors and Problems ........................................22
5.1 Error Messages..............................................................22
5.2 Troubleshooting .............................................................23
6. Maintenance and Storage.................................................24
7. Optional Parts....................................................................25
8. Technical Data...................................................................26
9. Some Useful Information about Blood Pressure ...........28
HEM-7000 main.book Page 2 Monday, June 19, 2006 8:53 AM

3
EN
Introduction
The OMRON M6 Comfort is a compact, fully automatic blood
pressure monitor, operating on the oscillometric principle. It
measures your blood pressure and pulse rate simply and
quickly. For comfortable controlled inflation without the need of
pressure pre-setting or re-inflation the devices uses its
advanced “IntelliSense” technology.
The device also stores up to 90 measurements in memory and
calculates an average value based on the last three
measurements taken within 10 minutes. Each measurement is
stored along with the date and time of measurement.
Please read this instruction manual thoroughly before
using the unit. Please keep for future reference.
For specific information about your own blood pressure,
CONSULT YOUR DOCTOR.
HEM-7000 main.book Page 3 Monday, June 19, 2006 8:53 AM

4
Important Safety Information
• Blood pressure measurement is not suitable in cases of
serious arteriosclerosis (hardening of the arteries).
• The pulse display is not suitable for monitoring the frequency
of cardiac pacemakers.
• Pregnant women should only measure their own blood
pressure in consultation with their doctor, since the readings
can be changed by pregnancy.
• Do not use the monitor on babies, young children or persons
who cannot express their consent.
• Do not use the monitor for any purpose other than measuring
blood pressure.
• The battery liquid may leak and damage the monitor. Please
observe the following points.
- When you are not going to use the unit for a long period of time
(approximately three months or more), take out the batteries.
- Replace old batteries with new ones immediately.
- Do not use old and new batteries together.
- Do not insert the batteries with their polarities incorrectly aligned.
• Please remember: Self-measurement is not the same as
medical treatment.
• You should never change the dose of medicines prescribed
by your doctor but you can help your doctor to optimize the
treatment by documenting the measured values. If there are
unusual values, please inform your doctor immediately.
• Never unplug the power cord with wet hands.
• Use only the original AC adapter designed for this unit. Use of
unsupported adapters may damage the device.
Read and follow the “Important information regarding Electro
Magnetic Compatibility (EMC)” in the Technical Data Section.
HEM-7000 main.book Page 4 Monday, June 19, 2006 8:53 AM

5
1.Overview
EN
1. Overview
Monitor
A. Display
B. O/I START button
C. Memory ( ) buttons
D. Date/Time ( ) setting
button
E. Battery compartment
F. Air jack
G. AC adapter jack (for optional
AC adapter)
B
D
A
C
E
G
F
HEM-7000 main.book Page 5 Monday, June 19, 2006 8:53 AM

6
1.Overview
Display
Package contents
H. Systolic blood pressure
I. Diastolic blood pressure
J. Memory symbol
K. Average value symbol
L. Movement error symbol
M. Irregular heartbeat symbol
N. Battery low symbol
O. Heartbeat symbol
1. Flashes during measurement
2. If flashing after measurement
complete indicates blood
pressure out of recommended
range
P. Pulse display
Q. Deflation symbol
R. Date/Time display
S. Arm cuff (Arm circumference
22-42 cm)
T. Air plug
U. Air tube
V. Storage case
W. Four “AA” alkaline (LR6)
batteries
H
O
Q
I
K
M
L
J
P
R
N
W
S
UT
V
HEM-7000 main.book Page 6 Monday, June 19, 2006 8:53 AM

7
2.Preparation
EN
2. Preparation
2.1 Installing/Replacing the Batteries
1. Remove the battery cover.
2. Insert four “AA” batteries as
indicated in the battery compartment
and then replace the battery cover.
Notes:
• If the battery low symbol ( ) appears on the display, replace
all four batteries at the same time.
- When the battery low symbol ( ) starts to blink, you will still
be able to use the unit for a short while. You should replace
the batteries with new ones ahead of time. Long-life alkaline
batteries are recommended.
- When the symbol ( ) remains lit, the batteries are
exhausted. You should replace the batteries with new ones
at once. Turn the unit off before replacing the batteries.
• Remove the batteries if the monitor will not be used for three
months or more.
• If the batteries are removed for 30 seconds or more, the Date/
Time setting will need to be reset. See “Setting the Date and
Time” for details.
• Disposal of used batteries should be carried out in accordance
with the national regulations for the disposal of batteries.
HEM-7000 main.book Page 7 Monday, June 19, 2006 8:53 AM

8
2.Preparation
2.2 Setting the Date and Time
Your blood pressure monitor automatically stores up to 90
measurements values in its memory and calculates an average
reading based on the measurements from the last three
readings taken within 10 minutes.
• Set the monitor to the correct date and time before taking a
measurement for the first time.
• If the batteries have been removed for 30 seconds or more,
the date and time setting will need to be reset.
1. When the batteries are installed, the
year digits will flash in the display
when you turn on the monitor.
Note: If you need to reset the date
and time for some reason,
hold down the button while the power is off.
2. Press the button to advance
the digits one at a time.
To change the digits to a lower
number, press the button to
lower the digits one at a time.
If you hold down the or
button, the digits will advance (or lower) rapidly.
3. Press the button to confirm the
setting when the desired number
appears on the display.
HEM-7000 main.book Page 8 Monday, June 19, 2006 8:53 AM

9
2.Preparation
EN
4. Repeat steps 2 and 3 to set the month and date (day).
5. Repeat steps 2 and 3 to set the hour and minutes for the time.
6. Press the O/I START button when
you have finished setting the date
and time.
or
or
or
or
HEM-7000 main.book Page 9 Monday, June 19, 2006 8:53 AM

10
3.Using the Unit
3. Using the Unit
3.1 How to Sit Correctly When Taking a Measurement
You can take a measurement on either your left or right arm.
Notes:
• Measurements should be taken in a quiet place and you
should be in a relaxed, seated position. Make sure that the
room is not too hot or cold.
• Avoid eating, smoking, or exercising for at least 30 minutes
before taking a measurement.
• Do not move or talk during measurement.
Correct
Posture Remove tight fitting clothing from
your upper arm, and any thick
clothing such as a sweater.
Do not place the cuff over thick
clothes and do not roll up your sleeve
if it is too tight.
Sit upright
with your
back straight. Place your arm on a table so
that the cuff will be at the same
level as your heart.
The gap between the
chair and the top of the
table should be between
25cm to 30cm.
HEM-7000 main.book Page 10 Monday, June 19, 2006 8:53 AM

11
3.Using the Unit
EN
Notes:
• Correct posture during measurement is necessary to get
accurate results.
• You should also try to measure your blood pressure at the
same time each day. (Within 1 hour after waking up is
recommended.)
Incorrect Posture
These situations could lead to higher blood pressure values due to
strain or the arm cuff being lower than the heart.
If the arm cuff is at a lower position than your heart use cushions
etc., to adjust the height of your arm.
•Arched back (leaning
forwards)
•Sitting cross-legged
•Sitting on a sofa or at a low
table so that you tend to lean
forward
HEM-7000 main.book Page 11 Monday, June 19, 2006 8:53 AM

12
3.Using the Unit
3.2 Applying the Arm Cuff
You can wrap the cuff either on your right or left arm.
• Remove tight-fitting clothing from
your upper arm.
• Do not place the cuff over thick
clothes and do not roll up your
sleeve if it is too tight.
1. Insert the air plug into the air jack (on the left side of the
device).
The cuff must be fully deflated when it is inserted into the air
jack.
2. Sit in a chair with your feet flat on the floor and place your arm
on a table so that the cuff will be at the same level as your
heart.
Air plug
Air jack
HEM-7000 main.book Page 12 Monday, June 19, 2006 8:53 AM

13
3.Using the Unit
EN
1) Hold the grip on the cuff securely with
your hand.
2) Turn the palm of your hand upward.
3. Turn the palm of your hand upward.
Apply the cuff to your upper arm so that the blue strip is centred
on the middle of your inner arm and points down the inside of
the arm. The air tube should run down the inside of your
forearm and be in line with your middle finger.
The bottom of the cuff should be approximately 1 to 2 cm
above the elbow.
Grip
Fabric fastene
r
Blue strip
Bottom edge 1 to 2cm
Air tube
HEM-7000 main.book Page 13 Monday, June 19, 2006 8:53 AM

14
3.Using the Unit
4. When the cuff is positioned correctly,
close the fabric fastener FIRMLY.
Notes:
• Make certain the cuff fits snugly around your arm.
• The cuff should make good contact with your skin. You should
be able to fit your index finger between the cuff and your arm
easily, so you can pull the cuff off and on.
• Make sure that there are no kinks in the air tubing.
Taking measurements on the right arm
Please note the following points
when applying the cuff to your right
arm. Apply the cuff so that the air
tube is at the side of your elbow.
Notes:
• Be careful not to rest your arm on
the air tube, or otherwise restrict
the flow of air to the cuff.
• Apply the arm cuff so that no part
of the cuff is positioned over the
elbow joint. The cuff should be 1 to
2 cm above the elbow.
• If used 2 times per day, the cuff will last for 3 years.
HEM-7000 main.book Page 14 Monday, June 19, 2006 8:53 AM

15
3.Using the Unit
EN
3.3 Taking a Reading
1. Press the O/I START button and remain still, the cuff will start
to inflate automatically.
As the cuff begins to inflate, the monitor automatically
determines your ideal inflation level. Remain still and do not
talk until measurement is completed.
Note: Do not inflate the cuff if it is not wrapped around your
arm.
2. Inflation stops automatically
and measurement is started.
As the cuff slowly deflates,
decreasing numbers appear
on the display and the
Heartbeat display flashes at every heartbeat.
In rare circumstances, the monitor might re-inflate the cuff to
continue with the measurement.
3. When the measurement is complete, the arm
cuff completely deflates and your blood
pressure and pulse rate are displayed.
Note: The monitor automatically stores the
blood pressure readings and pulse rate
along with date and time of measurement in its memory.
HEM-7000 main.book Page 15 Monday, June 19, 2006 8:53 AM

16
3.Using the Unit
4. Press the O/I START button to turn
the monitor off.
Note: If you forget to turn the
monitor off, it will
automatically shut itself off after five minutes.
Important:
• Wait 2-3 minutes before taking another blood pressure
measurement. Waiting between readings allows the arteries
to return to the condition prior to taking the blood pressure
measurement.
• If you move during measurement, the movement display
( ) may appear. Repeat the measurement and remain still
until the measurement is complete.
• Your blood pressure monitor includes an irregular heartbeat
feature. Irregular heartbeats can influence the results of the
measurement. The irregular heartbeat algorithm automatically
determines if the measurement is usable or needs to be
repeated. If the irregular heartbeat display ( ) is shown
after you have taken a measurement, repeat the
measurement. If the irregular heartbeat display ( ) is
shown frequently, please make your doctor aware of it.
• If your systolic blood pressure is above
135 mmHg or your diastolic blood pressure is
above 85 mmHg, the heartbeat symbol will blink
when the measurement result is displayed.
Recent research suggests that the following
values can be used as a guide to high blood
pressure for measurements taken at home.
This criteria is for home blood pressure measurement.
For professional office blood pressure measurement criteria,
please refer to Chapter 9 “Some Useful Information about
Blood Pressure”. Also in special cases (such as diabetics,
Systolic Blood Pressure Above 135 mmHg
Diastolic Blood Pressure Above 85 mmHg
HEM-7000 main.book Page 16 Monday, June 19, 2006 8:53 AM

17
3.Using the Unit
EN
heart- or circulation-disease) a lower limit of blood pressure
might be necessary and that it is recommended to consult the
doctor in such cases.
What is Irregular Heartbeat?
An irregular heartbeat is a
heartbeat rhythm that varies
by more than 25% from the
average heartbeat rhythm
detected while the unit is
measuring the systolic and
diastolic blood pressure.
If such an irregular rhythm is
detected more than twice
during measurement, the irregular heartbeat symbol ( )
appears on the symbol when the measurement results are
displayed.
What is Arrhythmia?
A heartbeat is stimulated by electrical signals that cause the
heart to contract.
Arrhythmia is a condition where the heartbeat rhythm is
abnormal due to flaws in the bio-electrical system that drives
the heartbeat. Typical symptoms are skipped heartbeats,
premature contraction, an abnormally rapid (tachycardia) or
slow (bradycardia) pulse. This can be caused by heart disease,
aging, physical predisposition, stress, lack of sleep, fatigue etc.
Arrhythmia can only be diagnosed by a doctor through a
special examination.
Whether the appearance of the irregular heartbeat symbol
( ) in the results indicates arrhythmia or not can only be
determined by an examination and diagnosis by your doctor.
If the irregular heartbeat symbol ( ) is shown frequently,
please make your doctor aware of it. Conducting self-diagnosis
and treatment based on measurement results is dangerous. Be
sure to follow the instructions of your doctor.
N
orma
l
H
eart
b
eat
Irregular Heartbeat
Pulse
Blood pressure
Blood pressure
Short Long
Pulse
HEM-7000 main.book Page 17 Monday, June 19, 2006 8:53 AM

18
3.Using the Unit
3.4 Instructions for Special Conditions
If your systolic pressure is known to
be more than 220 mmHg, after the
cuff starts to inflate, press and hold
the O/I START button until the
monitor inflates 30 to 40 mmHg
higher than your suspected systolic pressure.
Important:
• The monitor will not inflate above 300 mmHg.
• Do not apply more pressure than necessary.
HEM-7000 main.book Page 18 Monday, June 19, 2006 8:53 AM

19
3.Using the Unit
EN
3.5 Using the Memory Function
This monitor has a memory capable of storing 90 sets of
readings. Every time you complete the measurement, the
monitor automatically stores blood pressure and pulse rate with
the date and time. The monitor also calculates an average
reading based on the measurements from the last three
readings taken within 10 minutes.
If there are three readings within 10 minutes of the last reading,
the average of the three readings is displayed. (If there are only
two readings in memory for that period, the average will be
based on two readings. If there is only one reading in memory
for that period, that reading will be displayed as the average
value.)
Note: When 90 sets of readings are stored in memory, the
oldest set will be deleted to store a new set.
To View the Average Value
Press the memory button.
The average value, based on the last three measurements, is
displayed.
HEM-7000 main.book Page 19 Monday, June 19, 2006 8:53 AM

20
3.Using the Unit
To View Previous Readings Stored in Memory
1. Press the button, while the average reading is displayed,
to view reading stored in memory from the most recent to the
oldest.
2. Press the or button repeatedly to cycle through the
previous measurement values
( button: from the most recent to the oldest,
button: from the oldest to the most recent)
Keep the button pressed down to cycle rapidly through the
previous values.
To Delete All the Values Stored in Memory
Caution!
You cannot delete the stored readings partially, all the reading
in the monitor will be deleted.
To delete stored readings, press the memory button and
the O/I START button simultaneously, then all the readings will
be deleted.
Alternating display
HEM-7000 main.book Page 20 Monday, June 19, 2006 8:53 AM