Omron SYSMAC CJ1W-NC113 User manual

89Position control units
CJ1W-NC@@
Position control units
High-speed, High-precision
positioning with 1, 2, or 4 axes
• Positioning can done by direct ladder commands
• Position and speed control
• Linear interpolation
• Interrupt feeding function
• Positioning of 100 points done from memory
• S-curve acceleration/deceleration, origin search,
backlash compensation, and other features are also
supported.
• Positioning data is saved in internal flash memory,
eliminating the need to maintain a backup battery.
• Use Windows-based support software
(CX-position) to easily create positioning data
and store data and parameters in files.
These position control units support positioning control via pulse-train outputs. Positioning is performed using trapezoid al or
S-curve acceleration and deceleration. Models are available with 1, 2, or 4 axes control, and can be used in combination with
servo drives or stepping motors what accept pulse-train control.
System configuration
Function
CHARGEPOWER
SGDH-
200VVer .
CN3
CN1
CN2
CJ1 series
Position control unit
CJ1W-NC_
Limit switches
contact sensors
SmartStep
Servo Drive
SmartStep
Servo Motor
Personal computer
software: CX-One
Input
Servo
relay unit
Sigma-II series
Servo Drive
Sigma-II series
Linear Motor
Y203-EN2-02-Katalog.book Seite 89 Mittwoch, 24. Mai 2006 2:22 14

90 Motion controllers
Specifications
Position control unit
Servo drive cables
Note: Refer the selected servo systems section for cable and servo relay units information.
Computer software
Model CJ1W-NC113
CJ1W-NC133 CJ1W-NC213 CJ1W-NC233 CJ1W-NC413 CJ1W-NC433
Unit name Position control unit
Classification Special I/O unit
Unit numbers 0 to 95 0 to 94
Control method Open-loop control by pulse train output
Control output interface CJ1W-NC@13: Open-collector output
CJ1W-NC@33: Line-driver output
Controlled axes 1 2 4
Operating modes Direct operation or memory operation
Data format Binary (hexadecimal)
Affect on scan time for end refresh 0.29 to 0.41 ms max./unit
Affect on scan time for IOWR/IORD 0.6 to 0.7 ms max./instructions
Startup time 2 ms max. (refer to operation manual for conditions)
Position data -1,073,741,823 to +1,073,741,823 pulses
No. of positions 100 per axis
Speed data 1 to 500 kpps (in 1 pps units)
No. of speeds 100 per axis
Acceleration/deceleration times 0 t 250 s (time to max. speed)
Acceleration/deceleration curves Trapezoidal or S-curve
Saving data in CPU Flash memory
Windows-based support software CX-position (WS02-NCTC1-E)
Ambient operating temperature 0 to 55 °C 0 to 50 °C
External power supply 24 VDC ±10%, 5 VDC ±5% (line driver only) 24 VDC ±5%, 5 VDC ±5% (line driver only)
Ordering information
Name Model
1 axis position control unit. Open-collector output. CJ1W-NC113
2 axes position control unit. Open-collector output. CJ1W-NC213
4 axes position control unit. Open-collector output. CJ1W-NC413
1 axis position control unit. Line-driver output. CJ1W-NC133
2 axes position control unit. Line-driver output. CJ1W-NC233
4 axes position control unit. Line-driver output. CJ1W-NC433
Specifications Model
CX-One CX-One
In the interest of product improvement, specifications are subject to change without notice.
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.
Cat. No. I04E-EN-02
Y203-EN2-02-Katalog.book Seite 90 Mittwoch, 24. Mai 2006 2:22 14