Omron Z300 V3 - SETUP User guide

Authorized Distributor:
Z300 V3
Manual 1:
SETUP MANUAL
High-precision Visual Displacement
Measurement System
Cat. No. Z161-E1-03B
Cat. No. Z161-E1-03B
Note: Specifications subject to change without notice. Printed in Japan
1104-0.5M (M)
Cat. No. Z161-E1-03B Z300 V3 High
-precision Visual Displacement Measurement System
Manual 1: SETUP MANUAL

1
Z300 V3
High-precision Visual Displacement Measure-
ment System
Manual 1: Setup Manual
Revised November 2004

2

3
TABLE OF CONTENTS
PRECAUTIONS ................................................................................... 7
READ AND UNDERSTAND THIS DOCUMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
LIMITATIONS OF LIABILITY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
SUITABILITY FOR USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
PERFORMANCE DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
CHANGE IN SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
DIMENSIONS AND WEIGHTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
ERRORS AND OMISSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
PROGRAMMABLE PRODUCTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
COPYRIGHT AND COPY PERMISSION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Meanings of Signal Words. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Meanings of Alert Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Laser Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Regulations and standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Precautions for Safe Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Precautions for Correct Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Confirming Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Product Availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Visual Aids. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Notation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
SECTION 1
Features ............................................................................................... 21
1-1 Monitoring While Viewing the Measurement Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
1-2 Simple Setup Using Menus! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
1-3 A Wide Variety of Useful Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
SECTION 2
Wiring and Connection...................................................................... 25
2-1 Component Names and Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
2-2 System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
2-3 Connecting Peripheral Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
2-4 Power Supply and Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
2-5 Terminal Block Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
2-6 RS-232C Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
2-7 Linear Sensor Controller Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
SECTION 3
Installation .......................................................................................... 47
3-1 Mounting the Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
3-2 Mounting the Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
SECTION 4
Non-visual Mode................................................................................. 63
4-1 Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
4-2 DIP Switch Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
SECTION 5
Maintenance........................................................................................ 71

4
SECTION 6
Troubleshooting ..................................................................................73
SECTION 7
Appendix..............................................................................................77
7-1 Specifications and Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
7-2 Laser Product Classifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
Index.....................................................................................................95
Revision History ..................................................................................96

5
About this Manual:
This manual describes the hardware for the Z300 (High-precision Visual Displacement Measure-
ment System) and how to install the components, and it includes the sections described below.
This is one of two manuals used to operate the Z300. Refer to the following table for the contents of
each manual.
Please read the above manuals carefully and be sure you understand the information provided
before attempting to install or operate the Z300.
Section 1 Features introduces the features of the Z300.
Section 2 Wiring and Connection describes procedures for wiring power supplies and ground
wires and for connecting to external devices.
Section 3 Installation provides installation methods for the Controller and Sensor.
Section 4 Non-visual Mode explains how to make settings for Z300 operation using the DIP
switch instead of the menus.
Section 5 Maintenance explains maintenance procedures for ensuring the Z300's performance.
Section 6 Troubleshooting provides information on hardware errors that may occur with the
Z300. Refer to this section before requesting service from your OMRON representative.
Section 7 Specifications and Dimensions provides the specifications and dimensions of the
Z300 and its peripheral devices.
Manual Contents Cat. No.
1: Setup Manual Provides information on system hardware and instal-
lation. Be sure to read this manual first.
Z161
2: Operation Manual Describes operation of the Z300. Z162
WARNING Failure to read and understand the information provided in this manual may
result in personal injury or death, damage to the product, or product failure.
Please read each section in its entirety and be sure you understand the informa-
tion provided in the section and related sections before attempting any of the pro-
cedures or operations given.

6

7
PRECAUTIONS
This section provides general precautions for using the Z300 V3 Sensor.
The information contained in this section is important for the safe and reliable application of the Z300 V3
Sensor. You must read this section and understand the information contained before attempting to set up
or operate a Z300 V3 Sensor.
READ AND UNDERSTAND THIS DOCUMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
LIMITATIONS OF LIABILITY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
SUITABILITY FOR USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
PERFORMANCE DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
CHANGE IN SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
DIMENSIONS AND WEIGHTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
ERRORS AND OMISSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
PROGRAMMABLE PRODUCTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
COPYRIGHT AND COPY PERMISSION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Meanings of Signal Words. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Meanings of Alert Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Laser Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Regulations and standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Precautions for Safe Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Precautions for Correct Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Confirming Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Product Availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Visual Aids. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Notation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

READ AND UNDERSTAND THIS DOCUMENT
Please read and understand this document before using the products. Please consult your OMRON
representative if you have any questions or comments.
WARRANTY
OMRON’s exclusive warranty is that the products are free from defects in materials and workmanship
for a period of one year (or other period if specified) from date of sale by OMRON.
OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING
NON-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE
PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE
HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF
THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED.
LIMITATIONS OF LIABILITY
OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL
DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE
PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE,
OR STRICT LIABILITY.
In no event shall responsibility of OMRON for any act exceed the individual price of the product on
which liability is asserted.
IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER
CLAIMS REGARDING THE PRODUCTS UNLESS OMRON’S ANALYSIS CONFIRMS THAT THE
PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT
SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR
REPAIR.
SUITABILITY FOR USE
THE PRODUCTS CONTAINED IN THIS DOCUMENT ARE NOT SAFETY RATED. THEY ARE NOT
DESIGNED OR RATED FOR ENSURING SAFETY OF PERSONS, AND SHOULD NOT BE RELIED
UPON AS A SAFETY COMPONENT OR PROTECTIVE DEVICE FOR SUCH PURPOSES. Please
refer to separate catalogs for OMRON’s safety rated products.
OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to
the combination of products in the customer’s application or use of the product.
At the customer’s request, OMRON will provide applicable third party certification documents
identifying ratings and limitations of use that apply to the products. This information by itself is not
sufficient for a complete determination of the suitability of the products in combination with the end
product, machine, system, or other application or use.
The following are some examples of applications for which particular attention must be given. This is
not intended to be an exhaustive list of all possible uses of the products, nor is it intended to imply that
the uses listed may be suitable for the products:
• Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions
or uses not described in this document.

• Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical
equipment, amusement machines, vehicles, safety equipment, and installations subject to separate
industry or government regulations.
• Systems, machines, and equipment that could present a risk to life or property.
Please know and observe all prohibitions of use applicable to the products.
NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR
PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO
ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT IS PROPERLY RATED AND
INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
PERFORMANCE DATA
Performance data given in this document is provided as a guide for the user in determining suitability
and does not constitute a warranty. It may represent the result of OMRON’s test conditions, and the
users must correlate it to actual application requirements. Actual performance is subject to the
OMRON Warranty and Limitations of Liability.
CHANGE IN SPECIFICATIONS
Product specifications and accessories may be changed at any time based on improvements and
other reasons.
It is our practice to change model numbers when published ratings or features are changed, or when
significant construction changes are made. However, some specifications of the product may be
changed without any notice. When in doubt, special model numbers may be assigned to fix or
establish key specifications for your application on your request. Please consult with your OMRON
representative at any time to confirm actual specifications of purchased products.
DIMENSIONS AND WEIGHTS
Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when
tolerances are shown.
ERRORS AND OMISSIONS
The information in this document has been carefully checked and is believed to be accurate; however,
no responsibility is assumed for clerical, typographical, or proofreading errors, or omissions.
PROGRAMMABLE PRODUCTS
OMRON shall not be responsible for the user’s programming of a programmable product, or any
consequence thereof.
COPYRIGHT AND COPY PERMISSION
This document shall not be copied for sales or promotions without permission.
This document is protected by copyright and is intended solely for use in conjunction with the product.
Please notify us before copying or reproducing this document in any manner, for any other purpose. If
copying or transmitting this document to another, please copy or transmit it in its entirety.

10
The following signal words are used in this manual.
The following alert symbols are used in this document.
Meanings of Signal Words
WARNING
Indicates a potentially hazardous situation which, if not avoided, will result in minor or
moderate injury, or may result in serious injury or death. Additionally there may be
significant property damage.
Meanings of Alert Symbols
Cautions to indicate potential laser beam hazard
PRECAUTIONS

11
Sensor Head is a Class 3B Laser Product according to EN60825-1 (IEC60825-1) and Class II Laser
Product according to FDA (21 CFR1040.10) (see note). The Z510 Series is meant to be built into final
system equipment. Pay special attention to the following precautions for the safe use of the product:
Note:Europe: Class 2 and Class 3B of EN60825-1: 1994 = IEC60825-1: 1993
U.S.A.: Class II and Class IIIB of FDA (21 CFR1040.10).
(1)Use this product as specified in the operation manual. Otherwise, you may be exposed to
hazardous laser radiation.
(2)The Z300 series radiates laser beams in the visible light range. Do not expose your eyes directly to
the laser radiation. Ensure that the laser beam path is terminated during use. If a mirror or shiny
surface is positioned in the laser beam path, ensure that the reflected beam path is also terminated.
If the Unit must be used without terminating the laser beam path, position the laser beam path so
that it is not at eye level.
(3)To avoid exposure to hazardous laser radiation, do not displace nor remove the protective housing
during operation, maintenance, and any other servicing.
(4)The user should return the product to OMRON for all repair and servicing.
(5)As for countries other than those of Europe and the U.S.A., observe the regulations and standards
specified by each country.
As for the Laser Product Classifications, refer to the Appendix.
Refer to page 77.
Laser Safety
bWARNING
The laser radiation has a high power density and exposure may result in loss of sight.
Do not to expose your eyes to the laser radiation either directly or indirectly (i.e., after
reflection from a mirror or shiny surface).
Z300-S2T Z300-S5T Z300-S10 Z300-S60
Wave length 650 nm 670 nm 670 nm 658 nm
Maximum pulse
duration 7 ms 7 ms 7 ms 17.5 ms
Cycle 0.5 to 10 ms 0.5 to 10 ms 0.5 to 10 ms 0.5 to 25 ms
Peak power 1 mW max. 1 mW max. 1 mW max. 15 mW max.
Class 23B
PRECAUTIONS

12
Labeling on Laser Use
The Sensor has the following WARNING label on the side.
Re-labeling
The following labels are provided, to be used selectively according to countries.
for use in the U.S.: FDA label (Aperture label, Caution logo label, Certification and
Identification label)
for use in countries other than the U.S.: Warning label according to EN/IEC standards.
Be sure to turn off the sensor before replacing the label, or your hand or other body parts may
be exposed to the hazardous laser beam radiating from the sensor.
§Use in the U.S.
When a laser product mounted on a certain device is to be used in the U.S., it has to meet the
requirements set forth by the FDA (regulations for laser products set forth by the Food and
Drug Administration).
Applications have been approved by CDRH (Center for Devices and Radiological Health) for
Z300-S2T, Z300-S5T, Z300-S10, Z300-S60. Three different FDA labels are enclosed in the
sensor package. Attach them to the sensor body.
The Z300 is designed to be built into the finished system unit. Refer to the following technical
standard for installation.
21CFR1040.10 and 1040.11
Z300-S2T Z300-S5T
Z300-S10
Z300-S60
PRECAUTIONS

13
FDA Labels for Laser Products
Be sure to attach FDA labels; do not attach English WARNING labels by mis-
take.
Areas to Attach Labels
§Use in Countries Other than the U.S.
Replace the warning label in Japanese on the sensor main body with the attached EN/IEC
warning label upon use in countries other than the U.S. Attach the label in the area where the
original Japanese warning label was provided.
EN60825-1(IEC60825-1) standard is applied to products exported to European countries.
The Z300 conforms to the standard.
CAUTION
PEAKPOWER
PULSEDURATION
WAVELENGTH
1000
10000
670
µw
µs
ClassIICautionlogotype ClassIICautionlogotype
ApertureLabel CertificationandIdentificationLabel
AVOID
EXPOSURE
Thislaserproductcomplieswith
21CFR1040.10and1040.11.
ShiokojiHorikawa,Shimogyo-ku,
Kyoto600-8530JAPAN
OMRONCorporation
AYABEFactory,OMRONCorp.
Placeofmanufacture:
Manufacturedin
Laserradiation
isemittedfrom
thisaperture
Z300-S5T/S10
CAUTION
PEAKPOWER
PULSEDURATION
WAVELENGTH
1000
10000
650
µw
µs
1000
10000
650
µw
µs
Z300-S2T
1000
10000
670
µw
µs
ClassIIIBDangerlogotype
Z300-S60
DANGER
DANGER
PEAK POWER
PULSE DURATION
WAVE LENGTH
15000
25000
658
µw
µs
15000
25000
658
µw
µs
CAUTION
PEAKPOWER
PULSEDURATION
WAVELENGTH
1000
10000
650
µw
µs
CAUTION
PEAKPOWER
PULSEDURATION
WAVELENGTH
1000
10000
670
µw
µs
AVOID
EXPOSURE
Laserradiation
isemittedfrom
thisaperture
AVOID
EXPOSURE
Laserradiation
isemittedfrom
thisaperture
Thislaserproductcomplieswith
21CFR1040.10and1040.11.
ShiokojiHorikawa,Shimogyo-ku,
Kyoto600-8530JAPAN
OMRONCorporation
AYABEFactory,OMRONCorp.
Placeofmanufacture:
Manufacturedin
ClassII
Cautionlogotype
ClassII
Cautionlogotype
ApertureLabel
ApertureLabel
Certificationand
IdentificationLabel
Certificationand
IdentificationLabel
Thislaserproductcomplieswith
21CFR1040.10and1040.11.
ShiokojiHorikawa,Shimogyo-ku,
Kyoto600-8530JAPAN
OMRONCorporation
AYABEFactory,OMRONCorp.
Placeofmanufacture:
Manufacturedin
Z300-S2T
Z300-S60
Z300-S5T/S10
AVOID
EXPOSURE
Laser radiation
is emittedfrom
this aperture
Thislaserproductcomplieswith
21CFR1040.10and1040.11.
Shiokoji Horikawa, Shimogyo-ku,
Kyoto 600-8530JAPAN
OMRONCorporation
AYABEFactory, OMRONCorp.
Placeofmanufacture:
Manufacturedin
DANGER
DANGER
PEAK POWER
PULSE DURATION
WAVE LENGTH
15000
25000
658
AVOID DIRECT EXPOSURE TO BEAM
ClassIIIB
Dangerlogotype
Certificationand
IdentificationLabel
ApertureLabel
PRECAUTIONS

14
Warning Labels
Be sure to attach correct warning labels; do not attach FDA labels by mistake.
The Z300 conforms to the following EC directives and EN standards.
1. EC Directives
EMC Directive: No.89//336/EEC
2. EN Standards
EN61326: 1997+A1:1998+A2:2001(EMI:Class A)
Regulations and standards
1.0
10
670
Z300-S5T
Z300-S10
1.0
10
650
Z300-S2T
15
25
658
Z300-S60
PRECAUTIONS

15
Please observe the following precautions for safe use of the product.
(1) Do not use the Z300 in environment with flammable or explosive gases.
(2) Install the Z300 away from high-voltage devices and moving machinery to
allow safe access during operation and maintenance.
(3) Use the Z300 with the power supply voltages specified in this manual.
(4) Use crimp terminals for wiring. Do not connect the power supply wires by just
twisting stranded wire and connecting directly to the terminals.
(5) Use the wire and crimp terminals of the proper sizes as specified in this man-
ual.
(6) Confirm that wiring has been performed correctly before turning ON the
power supply.
(7) Cover the terminal blocks with the Terminal Block Protection Covers.
Uncovered terminal blocks can result in electric shock.
(8) Use a DC power supply with countermeasures against high-voltage spikes
(safe extra low-voltage circuits on the secondary side).
(9) Be sure to securely tighten the screws when mounting the Z300.
(10)Do not attempt to dismantle, repair, or modify the Z300.
(11)Dispose of the Z300 as industrial waste.
Precautions for Safe Use
PRECAUTIONS

16
Please observe the following precautions to prevent failure to operate, malfunctions, or undesirable
effects on product performance.
Components
The Sensor and Console connected to the Z300-VC10V4 Controller must be
products designed specifically for the Z300.
- Sensor (Z300-S2T, Z300-S5T, Z300-S10, Z300-S60)
- Console (Z300-KP)
Installation Site
Do not install the Z300 in locations subjected to the following conditions:
- Ambient temperature outside of 0 to +40°C for the F300-M09 Video Monitor
(recommended monitor) or outside of 0 to +50°C for other Z300 compo-
nents.
- Condensation due to rapid temperature fluctuations
- Relative humidities outside 35 to 85%
- Corrosive or flammable gases
- Dust, salt, or iron particles
- Direct vibration or shock
- Reflection of intense light (such as other laser beams or electric arc-weld-
ing machine)
- Strong magnetic fields
- Direct sunlight
- Water, oil, or chemical fumes or spray
Installation Orientation
Orientation of Controller
To improve heat dissipation, install the Controller in the following direction only:
CORRECT
Do not install the Controller in the orientations shown in the following diagram.
INCORRECT
Precautions for Correct Use
PRECAUTIONS

17
Ambient Temperature
- Maintain a minimum clearance of 50 mm above and below the Z300 to
improve air circulation.
- Do not install the Z300 immediately above significant heat sources, such as
heaters, transformers, or large-capacity resistors.
- Do not let the ambient temperature exceed 50°C.
- Provide a forced-air fan cooling or air conditioning if the ambient tempera-
ture is near 50°C so that the ambient temperature never exceed 50°C.
Ambient Illumination
Although the Z300 is rated for use in environments where the ambient illumina-
tion does not exceed 3000lx, if possible, do not use the Z300 near lighting equip-
ment that turns ON and OFF continuously. If this is unavoidable, reduce the
influence of the light by, for example, using a light baffle.
Noise Resistance
- Do not install the Z300 in a cabinet containing high-voltage equipment.
- Do not install the Z300 within 200 mm of power cables.
Sensor Maintenance
- Install the Sensor in a clean environment and keep the filter on the front panel
of the Sensor free from oil and dust. If affected by oil or dust, clean the filter as
follows:
1. Use a blower brush (used to clean camera lenses) to blow large dust parti-
cles from the surface. Do not blow the dust away with your mouth.
2. Use a soft cloth (for lenses) with a small amount of alcohol to remove the
remaining dust. Do not use a scrubbing action when cleaning as scratches
on the filter could result in the Sensor malfunctioning.
Environment
The Sensor cannot accurately detect the following types of objects:
- Objects with an extremely low reflection ratio
- Objects with a small curvature
- Largely inclined objects
Connecting Cables
Always turn OFF the Z300's power before connecting or disconnecting cable.
Control panel
Z300
Louver
Z300
200 mm min.
200 mm min.
Power cable
PRECAUTIONS

18
Touching Signal Lines in Connectors or Terminals
To prevent damage from static electricity, use a wrist strap or another device for
preventing electrostatic discharges when touching terminals or signal lines in
connectors.
Wiring
When using a transformer for the Z300's driving power supply, use an isolation
transformer in the way shown below. Do not use an auto-transformer. Doing so
may result in equipment failure.
Turning OFF the Power (Visual Mode Only)
Do not turn OFF the power while a message is being displayed indicating that
processing is being performed. Data in memory will be destroyed, and the Z300
may not operate correctly the next time it is started.
Using the RESET Signal
Do not use the RESET input immediately after power is turned ON. When using
the RESET input to synchronize startup timing, wait at least 1 second after the
Z300's power supply is turned ON before turning ON the RESET terminal.
Securing the Video Monitor (When Using the Recommended F150-M09)
Observe the following precautions to prevent noise interference, because the
video monitor case is connected to the 0 V line in the internal circuits.
1. Do not ground the video monitor.
2. Do not ground the metallic part of the connector.
3. Secure the video monitor with plastic screws if it is being mounted to a metal-
lic surface.
Z300
Z300
Auto-transformer
Isolation transformer
Commercial
power supply
Commercial
power supply
Scn 0▼SAVE▼
Saving data.
PRECAUTIONS

19
Warming Up
After turning ON the power supply, allow the Z300 to stand for at least 30 min-
utes before use. The circuits are unstable immediately after the power supply is
turned ON and attempting measurement may result in inconsistent measure-
ment values.
Check the contents of the package as soon as you receive the Z300. It is extremely rare for compo-
nents to be missing, but contact the nearest OMRON representative if any of the following items are
missing.
1. Z300-VC10EV3 Controller Qty: 1
2. SETUP MANUAL (This Manual) Qty: 1
3. OPERATION MANUAL Qty: 1
Some of the products listed may not be available in some countries. Please contact your nearest
OMRON sales office by referring to the addresses provided at the back of this manual.
The following headings appear in the left column of the manual to help you locate different types of
information.
Note Indicates information of particular interest for efficient and convenient operation
of the product.
Notice Indicates information required to take full advantage of the functions and perfor-
mance of the product. Incorrect application methods may result in the loss of
damage or damage to the product. Read and follow all precautionary informa-
tion.
CHECK Indicates points that are important in using product functions or in application
procedures.
1,2,3... Indicates lists of one sort or another, such as procedures, checklists, etc.
SeeAlso Indicates where to find related information.
Screen Messages In this manual, screen message are given in bold/italic.
E.g.: Application
Confirming Package Contents
Product Availability
Visual Aids
Notation
PRECAUTIONS