Omron A6T Series User manual
1
DIP Switch A6T/A6S
Low-cost DIP Switch with Slide Pins
Allows automatic mounting with DIP IC insertion
machines.
Washable models with seal tape are available.
SMT (surface-mounted terminal) models are
available.
Ordering Information
No.
of
l
Flat actuated
Raised actuator
Flat actuated
Raised actuator
poles Standard W
ith seal tape
Standard W
ith seal tape
DIP terminal DIP terminal DIP terminal
SMT terminal SMT terminal SMT terminal
1 A6T-1101 A6T-1102 A6T-1104 --- --- ---
2 A6T-2101 A6T-2102 A6T-2104 A6S-2101 A6S-2102 A6S-2104
3 --- --- --- A6S-3101 A6S-3102 A6S-3104
4 A6T-4101 A6T-4102 A6T-4104 A6S-4101 A6S-4102 A6S-4104
5 --- --- --- A6S-5101 A6S-5102 A6S-5105
6 A6T-6101 A6T-6102 A6T-6104 A6S-6101 A6S-6102 A6S-6104
7 --- --- --- A6S-7101 A6S-7102 A6S-7104
8 A6T-8101 A6T-8102 A6T-8104 A6S-8101 A6S-8102 A6S-8104
9 --- --- --- A6S-9101 A6S-9102 A6S-9104
10 A6T-0101 A6T-0102 A6T-0104 A6S-0101 A6S-0102 A6S-0104
A6T/A6S A6T/A6S
2
Specifications
Ratings/Characteristics
Switching
capacity
25 mA at 24 VDC
Insulation resistance
100 M
Ω
min. (at 250 VDC)
Contact resistance
200 m
Ω
max. (initial value)
Dielectric strength
500 V
AC for 1 min between terminals of same polarity
, and between terminals of dif
ferent polarity
V
ibration resistance
Malfunction:
10 to 55 Hz, 1.5-mm double amplitude
Shock resistance
Malfunction:
300 m/s
2
min. (approx. 30G min.)
Life expectancy
Mechanical:
1,000 operations min.
Electrical:
1,000 operations min.
Ambient temperature
Operating: –20°
C to 70
°
C (with no icing)
Ambient humidity
Operating:
35% to 90%
Operating force
0.29 N min. (30 gf)
Flammability rating
UL 94-0
Dimensions
Note: 1.
All units are in millimeters unless otherwise indicated.
2.
Unless otherwise specified, a tolerance of
±
0.4 mm applies to all dimensions.
Flat Actuated with DIP Terminal
Standard/With Seal Tape
A6T-j101
A6T-j102
Flat
Actuated
Standard W
ith Seal T
ape
Raised Actuator
Seal
tape (t = 0.06)
Raised Actuator
with DIP Terminal
A6T-j104
PCB
Dimensions
(T
op V
iew) 1.0±0.05 dia.
P: pole numbers
No.
of
poles Model A
1 A6T-1101 A6T-1102 A6T-1104 3.48
2 A6T-2101 A6T-2102 A6T-2104 6.02
4 A6T-4101 A6T-4102 A6T-4104 11.10
6 A6T-6101 A6T-6102 A6T-6104 16.18
8 A6T-8101 A6T-8102 A6T-8104 21.26
10 A6T-0101 A6T-0102 A6T-0104 26.34
A6T/A6S A6T/A6S
3
Flat Actuated with SMT Terminal
Standard/With Seal Tape
A6S-j101
A6S-j102
Flat
Actuated
Standard W
ith Seal T
ape
Raised Actuator
Seal
tape (t = 0.06)
Raised Actuator
with SMT Terminal
A6S-j104
PCB
Dimensions
(T
op V
iew)
P: pole numbers
No.
of
poles Model A
2 A6S-2101 A6S-2102 A6S-2104 6.02
3 A6S-3101 A6S-3102 A6S-3104 8.56
4 A6S-4101 A6S-4102 A6S-4104 11.10
5 A6S-5101 A6S-5102 A6S-5104 13.64
6 A6S-6101 A6S-6102 A6S-6104 16.18
7 A6S-7101 A6S-7102 A6S-7104 18.72
8 A6S-8101 A6S-8102 A6S-8104 21.26
9 A6S-9101 A6S-9102 A6S-9104 23.80
10 A6S-0101 A6S-0102 A6S-0104 26.34
Installation
Internal Connections (Top View)
Precautions
Circuit Design
Use the DIP Switch within the rated voltage and current ranges,
otherwise the DIP Switch may have a shortened life expectancy,
radiate
heat, or burn out.
Mounting
Do
not operate the DIP Switch while mounting, soldering, or wash
-
ing
the DIP Switch, otherwise the DIP
Switch may deform due the
heat of the solder, the DIP Switch may malfunction due to the pe-
netration of the washing agent, or the machine incorporating the
DIP
Switch may operate or be set incorrectly
.
An automatic insertion machine incorporating a body stopper is
available
for mounting the DIP Switch. When using an automatic in
-
sertion
machine incorporating a half-lead stopper to mount the DIP
Switch,
make sure that the automatic insertion machine will not de
-
form
the terminals of
the DIP Switch, otherwise the improper inser
-
tion
of the DIP Switch may result.
A6T/A6S A6T/A6S
4
Soldering
Observe the following conditions when soldering the DIP Switch.
Automatic Soldering Bath
Soldering temperature:
260°C max.
Soldering time:
5 s max. for a 1.6-mm thick,
single-side PCB
Reflow Soldering
Soldering time
Soldering
temperature
(°C)
2 minutes
max. 20 seconds
max.
Manual
Soldering
Soldering temperature:
350°
C at the tip of the soldering iron.
Soldering time:
3 s max. for a 1.6-mm thick,
single-side PCB
Set the pins of the DIP Switch to OFF before soldering the DIP
Switch.
Before
soldering the DIP Switch on a PCB, make sure that there is
no
unnecessary space between the DIP Switch and PCB.
Before soldering the DIP Switch on a multilayer PCB, make sure
that
the DIP Switch will
not be deformed by the soldering heat on the
pattern
or land of the multilayer PCB.
Do
not solder the DIP Switch more than twice including rectification
soldering. An interval of five minutes is required between the first
and
second solderings.
Make sure that there is no flux rise on the surface of the PCB.
PCB surface
Flux
Washing
Washable A6T
(with seal tape),
A6S (with seal tape)
Not washable
A6T
(standard/raised actuator),
A6S (standard/raised actuator)
Ultrasonic cleaning is unavailable to any A6T or A6S-series DIP
Switch
with a seal tape. It is possible to wipe or dip these models into
washing
agents for one minute maximum.
Apply
fluorocarbon or alcoholic solvents to clean washable
models.
Do not apply any other solvents or water to clean any washable
model
because they may deteriorate the materials or performance
of
the model.
Washing
equipment incorporating more than one washing bath can
be
used to clean washable models provided that the washable mod
-
els are cleaned for one minute maximum per bath and the total
cleaning
time does not exceed three minutes.
Do
not impose any external force on washable models while
wash
-
ing.
Do
not clean
washable models immediately after soldering. W
ait for
at
least three minutes to clean washable models after soldering.
The
A6T or A6S-series DIP Switch with a seal tape can be washed
provided
that the seal tape is not
removed or pasted before washing
the DIP Switch.
A6T/A6S A6T/A6S
5
Handling
Do
not apply excessive operating force to the DIP Switch, otherwise
the DIP Switch may be damaged or deformed, thus causing the
switch mechanism to malfunction as a result. Apply an operating
force
not exceeding 200% of the maximum rated operating force to
the DIP Switch.
Set
the DIP Switch incorporating slide pins with a tiny
, rounded ob
-
ject,
such as the tip
of a ball-point pen or small screwdriver
. Do not
set
the DIP Switch using tweezers or any other sharp object, which
may damage the DIP Switch. Do not set the DIP Switch using the
point of a mechanical pencil, otherwise lead powder or fragments
may
fall into the DIP Switch and internal circuit board, causing the
DIP
Switch to malfunction and reducing the dielectric
strength of the
circuit
board.
OMRON Corporation
Control
Components Division H.Q.
28th Fl., Crystal T
ower Bldg.
1-2-27, Shiromi, Chuo-ku,
Osaka 540 Japan
Phone:
06-949-61
15 Fax: 06-949-6134
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To
convert millimeters into inches, multiply by 0.03937. T
o convert grams into ounces, multiply by 0.03527.
Cat. No. A102-E1-1 In the interest of product improvement, specifications are subject to change without notice.
Printed
in Japan
0996-1M (0996)
a
This manual suits for next models
49
Table of contents
Other Omron Switch manuals
