Optex fit Series User manual

ENGLISH FRANÇAIS DEUTSCH ITALIANO ESPAÑOL PORTUGUÊS
EN-1
No.59-2267-1
INSTALLATION INSTRUCTIONS
Compact outdoor
detector
Compact outdoor
detector
fit series
fit series
• Long battery life
• Easy wiring by a connector
• Multi fixing separate box
• Compact design
• 190° adjustable bracket
• Intelligent AND logic
• Digital anti-masking (RAM model)
• Wall tamper (option)
CONTENTS
The check mark indicates recommendation.
Warning
Caution
Failure to follow the instructions provided with this indication and improper handling may cause
death or serious injury.
Failure to follow the instructions provided with this indication and improper handling may cause
injury and/or property damage.
FTN-R Battery operated model with 2 PIRs
FTN-RAM FTN-R with anti-masking
1 INTRODUCTION
1-1 BEFORE INSTALLATION ...................................... 1
1-2 PARTS IDENTIFICATION...................................... 2
1-3 DETECTION AREA................................................ 2
2 INSTALLATION
2-1 WIRING DIAGRAM ................................................ 2
2-2 TRANSMITTER PREPARATION ........................... 3
2-3 BEFORE WALL MOUNTING ................................. 3
2-4 STACKING METHOD............................................. 4
2-5
SIDE-BY-SIDE AND TOP-TO-BOTTOM METHOD ... 6
3 WALK TEST
3-1 WALK TEST ........................................................... 7
4 DIP SWITCH SETTING
4-1 WALK TEST MODE ............................................... 7
4-2 BATTERY SAVING TIMER .................................... 7
4-3 ALARM & TROUBLE OUTPUT.............................. 8
4-4 LED ........................................................................ 8
4-5 PIR SENSITIVITY .................................................. 8
4-6 ANTI-MASKING...................................................... 8
5 OTHERS
5-1 WALL TAMPER (OPTION) CONNECTION ........... 9
5-2 LED LIGHT PATTERN ........................................... 9
6 BATTERY
6-1 HOW TO REPLACE BATTERY ............................. 9
6-2 BATTERY LIFE ...................................................... 9
7 SPECIFICATIONS
7-1 SPECIFICATIONS................................................ 10
7-2 DIMENSIONS....................................................... 10
Consider the direction of the intruder,
for the setting of the detection area.
Do not remove
the separate box
tamper.
Do not remove the PCB. Do not touch
the PCB except for
the DIP switch. ON
1 2 3 4 5 6
ON
1234 5 6
0.8 to 1.2 m
(2.6 to 3.9 ft.)
Parallel
Mounting height. Keep the detector
parallel to the ground.
Install the detector in a place where it is free from false alarm factors. For example:
• Sunlight and reflection • Heat source • Objects moving in the wind
Tilt
Warning Caution Caution
The nix sign indicates prohibition.
WIRELESS MODEL
1INTRODUCTION
1-1 BEFORE INSTALLATION

ENGLISHFRANÇAISDEUTSCHITALIANOESPAÑOLPORTUGUÊS
EN-2
-Optional accessories
Wall tamper (WRS-03)
Separate box
Separate box tamper
Main unit
Bracket
Fixture
Main unit
cover
Lens
Separate
box cover
Sponge
Sponge
Plate nut
For joint
For wall mounting Screw
(3 × 20 mm)
Screw
(M3 × 10mm)
Connector for POWER and
ALARM
Sponge for transmitter
Connector for TROUBLE
Side viewTop view
2 m detection length
5 m detection length
0.8
0
(m)
1.0
1.2
2.6
0(ft.)
3.3
3.9
(m)
(ft.)
0 1 2 3 4 5
0 5 10 15
(ft.)
0 5 10 15
(m)
0 1 2 3 4 5
2.6
0(ft.)
3.3
3.9
0.8
0
(m)
1.0
1.2
0
1 2 3 4 50
0
0
5
5
5
10
10
10
15
15
15
1
1
1
2
3
4
5
(m) (ft.)
(ft.)
(m)
2
4
5
3
Adjustable range: 95°
(by 5° pitch)
Adjustable range: 95°
(by 5° pitch)
Separate box tamper
Trouble
Alarm
Wall tamper (option)
* For wall tamper wiring
(option), refer to 5-1.
Separate box Main unit
Transmitter
- Overall wiring diagram
Note>>
• The battery in the transmitter is shared with the
detector.
• Connection for TROUBLE is used when monitoring
for Tamper and Anti Mask.
Note>>
Transmitter and battery are not included.
2INSTALLATION
2-1 WIRING DIAGRAM
1-2 PARTS IDENTIFICATION
1-3 DETECTION AREA

ENGLISH FRANÇAIS DEUTSCH ITALIANO ESPAÑOL PORTUGUÊS
EN-3
... DIP switch 3: OFF (N.C.) ... DIP switch 3: ON (N.O.)
Connectors to be used
Connector for POWER and ALARM
Connector for TROUBLE
How to position a battery
N.C. N.O.
35 (1.38)
130 (5.12)
30 (1.18)
Unit: mm (inch)
The transmitter used should have the internal dimensions of H 130 × W 30 × D 35 mm.
(H 5.12 × W 1.18 × D 1.38 inches)
Red Black
External input is N.C. External input is N.O.
- When monitoring ALARM and TROUBLE using the transmitter with 1 external input
3
BracketMain unit
2.
1.
1Open the main unit cover. 2Remove the fixture.
Fixture
4Open the separate box.
Hold the top of the bracket and remove the main unit.
5Select the mounting method.
Stacking method (2-4) Side-by-side method (2-5) Top-to-bottom method (2-5)
Note>>
• Be sure to keep connectors
installed through the bottom part of
bracket after main unit is removed.
Note>>
• Do not remove the
separate box tamper.
Note>>
• Be sure to mount the
main unit on the top.
- To monitor only the ALARM using a transmitter
with 1 external input - To monitor the ALARM and TROUBLE using a transmitter with 2 external inputs
Connector for
POWER and
ALARM
Connector for
TROUBLE
Connector for
POWER and
ALARM
3 3
2-2 TRANSMITTER PREPARATION
2-3 BEFORE WALL MOUNTING

ENGLISHFRANÇAISDEUTSCHITALIANOESPAÑOLPORTUGUÊS
EN-4
For the side-by-side method and the top-to-bottom method, refer to page 6.
6Open the knockout.
Separate box
Wall mounting
knockout
Separate box cover
Wiring knockout
7Pull the connectors through
the wiring knockout.
8Attach the separate box cover and the
bracket.
9Hold the top part of the bracket
and mount the main unit.
1.
3.
2.
10 Mount the separate box on the wall.
Screw (3 × 20 mm)
Screw (3 × 20 mm)
100 mm
(3.94 inches)
Screw (3 × 10 mm)
Screw (3 × 10 mm)
Sponge
Plate nut
Plate nut
Wiring
Sponge
Joint screw
knockout
Joint screw
knockout
Wall mounting
knockout
Mounting height:
0.8 to 1.2 m
(2.6 to 3.9 ft.)
Double-sided tape
for temporary fixing
2-4 STACKING METHOD
Notes>>
• The tamper output is not exclusive.
The anti-masking and tamper circuits share the trouble output.
• For the wall tamper wiring connection (option), refer to 5-1.
• If the tamper connection is made between the main unit and the
separate box, cut the jumper wire (orange) as illustrated.
Otherwise, neither the separate box tamper nor the option wall
tamper switch will be activated. Conversely, if the tamper
connection is not made between them even the jumper cutting
situation, the trouble signal will remain activate.
11 Connect the connectors.
Separate box side Main unit side 12 Install the transmitter and attach
the separate box cover.
1.
2.
3.
Red
Black
White
Yellow
Green
Blue
Brown
Orange
Grey
Red: Power input (+)
Black: Power input (-)
White: Alarm
Yellow: Alarm
Green: Trouble
Blue: Trouble
Brown: Tamper
Orange: Tamper
Grey: Tamper
Transmitter
Note>>
• Please use the sponge for
transmitter when needed.
Note>>
• Be careful not to attach separate
box cover upside down.
• Be careful not to pinch wires.

ENGLISH FRANÇAIS DEUTSCH ITALIANO ESPAÑOL PORTUGUÊS
EN-5
14 Determine the detection length. (2 m or 5 m)
Side view
0 5 10 15
2.6
0(ft.)
3.3
3.9
0.8
0
(m)
1.0
1.2
(ft.)
10 2 3 4 5
(m)
0 5 10 15
0.8
0
(m)
1.0
1.2
2.6
0(ft.)
3.3
3.9
10 2 3 4 5
(m)
(ft.)
Side view
5 m detection length (Factory default)
2 m detection length
If 2 m is required, rotate the lower
lens 180 degrees.
15 Attach the main unit cover. 16
17
ON
12345 6
ON
123456
Perform walk test.
After walk test is complete, set DIP switch 1 (WALK TEST MODE) from “ON” to “OFF”.
Note>>
• To prepare for walk test, check that DIP switch
1 (WALK TEST MODE) is set to “ON (TEST)”
before attaching main unit cover.
Note>>
• The battery life will be shortened unless the
DIP switch 1 is set to “OFF”.
• To use the LED in normal operating
condition, set the DIP switch 4 to “ON”.
13 Determine the horizontal detection angle
and attach the fixture.
1.
3.
2.
• When the unit is mounted on the
wall to look transversely,
choose the guide-mark
engraved.
• When the unit is mounted on the
corner to look ahead along the wall,
choose the guide-mark
located on the opposite
side of the wall.
Note>>
• Check that the fixture and
bracket engage correctly.
Note>>
Align the detection area
parallel to the wall to
reduce interference with
the wall.
Note>>
• To make adjustments, remove the fixture.
Note>>
• Do not remove the upper lens.
DIP switch
ON
123456

ENGLISHFRANÇAISDEUTSCHITALIANOESPAÑOLPORTUGUÊS
EN-6
10 Connect the connectors.
Notes>>
11
Transmitter
1.
2.
3.
Separate box side Main unit side
Red
Black
White
Yellow
Green
Blue
Brown
Orange
Grey
Red: Power input (+)
Black: Power input (-)
White: Alarm
Yellow: Alarm
Green: Trouble
Blue: Trouble
Brown: Tamper
Orange: Tamper
Grey: Tamper
Install the transmitter and
attach the separate box cover.
12 For the subsequent procedure, refer to
steps 13 to 17 (page 5).
2-5 SIDE-BY-SIDE AND TOP-TO-BOTTOM METHOD
6Open the knockout.
Main unit
(Back surface)
Separate box
(Back surface)
Separate box
For the stacking method, refer to 2-4.
7Pull the wire connectors through wiring
knockout.
Wall mounting
knockout
Wall mounting
knockout
Wiring knockout
Wiring knockout
(For side-by-side method)
8Mount the bracket and the separate box to the wall.
Screw (3 × 20 mm)
Screw (3 × 20 mm)
Hold the top part of the bracket
and mount the main unit.
1.
3.
2.
Mounting
height:
0.8 to 1.2 m
(2.6 to 3.9 ft.)
100 mm
(3.94 inches)
83.5 mm
(3.29 inches)
Wiring knockout
(For top-to-bottom method)
• The tamper output is not exclusive. The anti-masking and
tamper circuits share the trouble output.
• For the wall tamper wiring connection (option), refer to
5-1.
• If the tamper connection is made between the main unit
and the separate box, cut the jumper wire (orange) as
illustrated. Otherwise, neither the separate box tamper
nor the option wall tamper switch will be activated.
Conversely, if the tamper connection is not made
between them even the jumper cutting situation, the
trouble signal will remain activate.
Double-sided
tape
Double-
sided
tape
Side-by-side
method
Top-to-bottom
method
Sponge Sponge
9
Note>>
• Be careful not to pinch wires.
Wiring

ENGLISH FRANÇAIS DEUTSCH ITALIANO ESPAÑOL PORTUGUÊS
EN-7
3
2
1
Detected Not detected
Note>>
Check that LED lights for 2 seconds
when the intended object is detected.
Set the DIP switch 1 (WALK TEST MODE) to “OFF (NORM)”.
Set the DIP switch 1 (WALK TEST MODE) to
“ON (TEST)”.
ON
12345 6
ON
12345 6
●: Factory default
ON
123456
ON
123456
ON
123456
TEST
NORM
5S
120S
5S
120 sec.
5 sec.
FunctionPosition
120S
(Factory default)
TEST
(Factory default)
• The LED lights irrespective of the DIP switch 4
(LED) setting.
• The DIP switch 2 (BATTERY SAVING TIMER)
setting is inactive.
• The LED lights depending on the DIP switch 4
(LED) setting.
• The DIP switch 2 (BATTERY SAVING TIMER)
setting is active.
FunctionPosition
NORM
• The switch is set to “ON (TEST)” by factory default.
Note>>
• The detector will not generate alarms at
intervals shorter than the specified time.
Note>>
• The battery life will be shortened unless the DIP switch 1 is set to “OFF”.
• To use the LED in normal operating condition, set the DIP switch 4 to “ON”.
DIP switch
1 WALK TEST MODE
2 BATTERY SAVING TIMER
3 ALARM & TROUBLE OUTPUT
4 LED
5 PIR SENSITIVITY
6 ANTI-MASKING Do not touch the
PCB except for the
DIP switch.
ON
12345 6
ON
12345 6
DIP switch
ON
12345 6
ON
12345 6
DIP switch
3WALK TEST
4DIP SWITCH SETTING
3-1 WALK TEST
4-1 WALK TEST MODE DIP switch 1 FTN-R
FTN-RAM
4-2 BATTERY SAVING TIMER DIP switch 2 FTN-R
FTN-RAM
ON
123456
ON
123456

ENGLISHFRANÇAISDEUTSCHITALIANOESPAÑOLPORTUGUÊS
EN-8
-ANTI-MASKING function
ANTI-MASKING test mode
Normal mode
The trouble is output after
3 minutes.
10 minutes1 minute
ON
(Factory default)
ANTI-MASKING OFF
ANTI-MASKING ON
FunctionPosition
OFF
ON
OFF
Teaching
When masking condition continues more than 3 minutes, TROUBLE will be generated.
TROUBLE is generated after 20 seconds under the anti-masking test mode.
Teaching mode starts when both the separate box cover and the main unit cover are attached.
Please be careful not to leave any object within 1 m from the unit.
The trouble is output after
20 seconds.
ON
LED OFF
LED ON
FunctionPosition
OFF
(Factory default)
LOW Low sensitivity
Normal sensitivity
FunctionPosition
STD
(Factory default)
ON
OFF
STD
LOW
Note>>
• If the LED lights, check the DIP switch 1
(WALK TEST MODE) setting.
N.O.
N.C.
N.O.
N.C. output
N.O. output
FunctionPosition
N.C.
(Factory default)
4-3 ALARM & TROUBLE OUTPUT DIP switch 3 FTN-R
FTN-RAM
4-4 LED DIP switch 4 FTN-R
FTN-RAM
4-5 PIR SENSITIVITY DIP switch 5 FTN-R
FTN-RAM
4-6 ANTI-MASKING DIP switch 6 FTN-R
FTN-RAM
ON
123456
ON
123456
ON
123456
ON
123456

ENGLISH FRANÇAIS DEUTSCH ITALIANO ESPAÑOL PORTUGUÊS
EN-9
Detector condition LED indicator
Warm-up 120 sec.
Alarm 2 sec.
Masking detection
(FTN-RAM only) Blinks 3 times and then repeats.
Blinks for approx. 120 seconds.
Lights for 2 seconds.
LED
Blink OFFLight
CR123A (3 V, 1300 mAh)
CR2 (3 V, 750 mAh)
1/2AA (3.6 V, 1000 mAh)
Approx. 6 years
Approx. 4 years
Approx. 5 years
Approx. 5 years
Approx. 3 years
Approx. 4 years
Interval 5 secInterval 120 sec
Notes>>
• The LED blinks even if the DIP
switch 4 (LED) is set to “OFF”.
Notes>>
• Data shown here is when the LED is
off, AM is on. Battery life becomes
shorter when the LED is on.
1
Stacking method Side-by-side method and
top-to-bottom method
Separate box
Separate
box cover
Separate box
Separate
box cover
Black Red
3
2Replace the battery.
3Connect the connector, and close
the separate box.
Note>>
• Check that the warm-up period
is started.
Open the separate box, and disconnect the transmitter
connector. (It is not necessary for the main unit to be opened.)
5OTHERS
6BATTERY
5-1 WALL TAMPER (OPTION) CONNECTION
5-2 LED LIGHT PATTERN
6-1 HOW TO REPLACE BATTERY
6-2 BATTERY LIFE
Mounting position
Stacking method Side-by-side method and top-to-bottom
method
Separate box side Main unit side
Wall tamper (option)
WRS-03
Bracket
Sponge
Separate
box
Sponge
Connect the tamper connector as shown below
when connecting a wall tamper (option).
The detector shares the battery with the transmitter. Check that the 2.5 to 10.0 V power battery is used for the
transmitter.
The following explains the LED light pattern.
The values indicated are only for reference on condition that the detector is exceptionally operated by the sole battery.
It is impossible to indicate the battery life under the normal operation as the battery in the transmitter is shared with the
detector.

ENGLISHFRANÇAISDEUTSCHITALIANOESPAÑOLPORTUGUÊS
EN-10
Note>>
• These units are designed to detect an intruder and activate an alarm control panel. Being only a part of
a complete system, we cannot accept responsibility for any damages or other consequences resulting
from an intrusion.
* Specifications and design are subject to change without prior notice.
Model
Detection method
PIR coverage
Detection length limit
Detectable speed
Sensitivity
Operation voltage
Power input
Current draw
Alarm period
Warm-up period
Alarm output
Trouble output
LED indicator
Operation temperature
Environment humidity
Weatherproof
Mounting
Mounting height
Weight
Accessories
FTN-RAMFTN-R
Passive infrared
5 × 1 m (16.4 × 3.3 ft.)
2 m, 5 m (6.6 ft., 16.4 ft.)
0.3 to 1.5 m/s (1 to 4.9 ft./s)
2.0°C (at 0.6 m/s) (3.6°F (at 2 ft./s))
2.5 to 10 VDC
3 to 9 VDC (Lithium or Alkaline Battery)
2.0 ±1.0 sec.
Approx. 120 sec. (LED blinks)
-20°C to +60°C (-4°F to +140°F)
95% max.
IP55
Wall (Outdoor, Indoor)
0.8 to 1.2 m (2.6 to 3.9 ft.)
190 g (6.7 oz.)
9 μA (at stand-by)/
3 mA (max.)
(at 3 VDC)
10 μA (at stand-by)/
3 mA (max.)
(at 3 VDC)
N.C./N.O.
Selectable-Solid State Switch
10 VDC 0.01 A (max.)
N.C./N.O.
Selectable-Solid State Switch
10 VDC 0.01 A (max.)
Enable: During DIP switch 1 (WALK TEST
MODE) or DIP switch 4 (LED) ON
Disable: During normal operation
Light/Blink: Warm-up, alarm,
masking detection (FTN-RAM only)
Connector for POWER and ALARM,
connector for TROUBLE, plate nut × 2,
screw (M3 × 10 mm) × 2,
screw (3 × 20 mm) × 4,
sponge for transmitter
Unit: mm (inch)
Unit: mm (inch)
35
(1.38) 42.5 (1.67)
35
(1.38) 42.5 (1.67)
155 (6.10) 155 (6.10)
7SPECIFICATIONS
7-1 SPECIFICATIONS 7-2 DIMENSIONS
■ EU contact information
Manufacturer:
OPTEX CO., LTD.
5-8-12 Ogoto, Otsu, Shiga, 520-0101 JAPAN
Authorised representative in Europe:
OPTEX (EUROPE) LTD. / EMEA HEADQUARTERS
Marandaz House 1 Cordwallis Park, Clivemont Road,
Maidenhead, Berkshire, SL6 7BU U.K.
OPTEX CO., LTD. (JAPAN)
URL: http://www.optex.net
OPTEX INC. (U.S.)
URL: http://www.optexamerica.com
OPTEX DO BRASIL LTDA. (Brazil)
URL: http://www.optex.net/br/es/sec
OPTEX (EUROPE) LTD. / EMEA HQ (U.K.)
URL: http://www.optex-europe.com
OPTEX SECURITY SAS (France)
URL: http://www.optex-security.com
OPTEX SECURITY Sp.z o.o. (Poland)
URL: http://www.optex.com.pl OPTEX (DONGGUAN) CO.,LTD.
SHANGHAI OFFICE (China)
URL: http://www.optexchina.com
Copyright (C) 2016 OPTEX CO.,LTD.
OPTEX KOREA CO.,LTD. (Korea)
URL: http://www.optexkorea.com
OPTEX (Thailand) CO., LTD. (Thailand)
URL: http://www.optex.net/th/th
OPTEX PINNACLE INDIA, PVT., LTD. (India)
URL: http://www.optex.net/in/en/sec
OPTEX TECHNOLOGIES B.V.(The Netherlands)
URL: http://www.optex.eu