Optex CX-702 MKII User manual

CX-702 , CX-702V
PASSIVE INFRARED DETECTOR
CX-702 / CX-702V
- Dual Purpose Lens:Selectable ”WIDE ANGLE” and
“LONG RANGE” detection patterns
- Double Conductive Shielding of the pyroelectric element
Extremely High Light and RFI Immunity (Patent listed)
- Multifocus Optics Design (Patent listed)
- LED On/Off Switch
- Sealed Optics
- Easy Installation
FEATURES
OPTION
CA-1W : Wall Mount Bracket : adjustable ±45°(Horizontally), 0-20°(Vertically downwards)
CA-2C : Ceiling Bracket : adjustable ±45°(Horizontally), 0-20°(Vertically downwards)
1.INSTALLATION HINTS
2.DETECTION AREA
Avoid Curtain,Screen,etc.
blocking detection area.
Avoid vapor or high humidity
that can cause condensation.
Avoid direct sunlight. Do not install outdoors.Avoid mounting detector where
movement of Fans or Air
Conditioning Fans can be detected.
8.TROUBLE SHOOTING
NOTE
These units are designed to detect movement of an intruder and activate
an alarm control panel.
Being only part of a complete alarm system,we cannot accept
responsibility for any damages or other consequences resulting from an
intrusion.
These products conform to the EMC Directive 89/336 EEC.
Dimensions : inches (mm)
9.SPECIFICATIONS
CX-702V Only
- Alarm Memory
- LED Remote Control Terminal
STANDARD ALARM MEMORY
3.94(100)
5.51 (140)
2.72 (69)
No.59-0951-2 0201-29
*Specifications and design are subject to change without prior notice.
CX-702V
8mA(normal) / 16mA(max.) at 12VDC
See Section7-3.
See Section7-1.
Model
Current draw
Alarm Memory
D.L.terminal
When damage has occured to the
product, i.e. water logged, abnormal
things inside product, overheating
or smoking, strange smells etc.,
WARNING
Never repair or modify
product. It may cause
accident, fire hazard or
electric shock.
WARNING
CAUTION
Mount securely.
A falling product
may cause injury.
PROBLEM
LED does not light.
LED lights even
though no person
within area.
LED lights but
signal is not sent.
LED continues to light
PROBABLE CAUSE
Improper power supply voltage
(disconnection,low voltage).
Improper detection area.
LED switch is OFF.
Improper polarity to detector.
Moving object within area (curtain, wall hanging, etc.).
Temperature of object within area changing rapidly
(heater, air conditioning, etc.).
Relay contact is stuck or damaged due to overloading.
Faulty wiring.
Poor connection of alarm memory.
Wrong control voltage from panel.
REMEDY
Correct supply voltage to 9.5 - 16V DC.
See Section 5.
See Section 2.
Turn on the switch.
Switch positive and negative at terminal.
Remove the souces from the detection area.
Remove object from the detection area.
Check load of output.
The unit needs repair or replacement.
Wire correctly.
Reconnect wire.
Must be 0-1V DC(grounded) See Section 7-3.
1 2 3 4 5
6 7 8
*The CX-702 is UL Listed per UL639,
Intrusion-Detection Units.
*The CX-702V has not been
investigated by UL.
(CX-702 Only)
N219
**ATTENTION**
The specified detection area can be achieved by mounting the unit at a height of 8ft.(2.4m). Mounting at a lower or higher height may reduce the area of coverage.
CX-702
8mA (normal) / 11mA (max.) at 12VDC
Model
Detection method
Coverage
Detection zones
Mounting height
Sensitivity
Detectable speed
Power input
Alarm period
Alarm output
Tamper switch
Pulse count
Warm-up period
LED indicator
RF interference
Operating temperature
Environment humidity
Weight
CX-702 / CX-702V
Passive infrared
Wide Angle 85°wide Long Range
70ft. × 70ft. 150ft. × 8ft.
(21m × 21m) (45m × 2.4m)
68 zones 22 zones
5 - 12ft.(1.5 - 3.6m)
3°F at 2ft./sec., 8ft. mounting height
(1.6°C at 0.6m/sec., 2.4m mounting height)
1- 5ft. / sec. (0.3 - 1.5m/sec.)
9.5 - 16VDC
Approx. 2.5 sec.
N.C. 28VDC 0.2A max.
N.C. Opens when cover is removed.
28VDC 0.1A max.
Approx. 20 sec. 2 or 4
Approx. 1 min.
Alarm condition
No alarm 30V/m
-4°F - +122°F(-20°C - +50°C)
95% max.
7.0oz (200g)
Model
Current draw
immediately stop using product and contact your supplier.
Otherwise, continued use in such condition may cause
electric shock or fire hazard.

4.INSTALLATION
5.WIRING
Loosen fastening
screw and remove
cover.
Lead in wires through knockouts
along the wiring guide on the
rear side of base. Mount base
with supplied screws. When
using a bracket, check matching
knockout position before opening
mounting holes.Wire according
to Section 5.
Conduct a walktest and
make adjustments
(Section 7). Fit cover
using fastening screw.
CX702
7.FUNCTIONS
CX-702V
Operation
If the unit triggered during armed period, when the system is
disarmed, LED will remain lit to confirm that it reported an alarm.
· Alarm Memory will operate even when LED is switched OFF.
· Alarm Memory will not operate while system is disarmed.
· After Alarm Memory latches, Alarm Output and LED operate
normaly during armed period.
Reset
Alarm Memory resets automatically
when system is re-armed.
2 : For normal applications.
4 : For use in hostile areas where there may be movement of small animals or
other objects such as fax machines or curtains.
When the “4” is selected, the detector’s sensitivity may seem sluggish. It is therefore important to always
conduct a walktest to ensure that the desired coverage is given.
Alarm Memory
This function is used to indicate if the detector was activated while the panel
was armed. It will cause the red LED on the Detector to illuminate once the
panel has been disarmed.
Compatible Control Panel is required for Alarm memory.
Connect A.M. terminal to Control Panel’s Control Voltage Signal terminal
(System Arming Status Voltage Output).
123
456
Jumper Pin Switch
The Alarm LED indicator can be switched either “ON” or “OFF”.
D.L. terminal (CX-702V Only)
LED can be enabled or disabled remotely from control panel by D.L. terminal.
1) Place Jumper Pin Switch in OFF position.
2) LED”ON” : Connect DL terminal to common ground with detector.(0~1VDC, grounded)
LED”OFF”: No Connection to the DL terminal.(OPEN or +5~16VDC)
3. ALARM MEMORY ( CX-702V Only )
3.DESCRIPTION AND OPERATION
Wiring Knockout
Terminals
Corner mount Knockout
Tamper switch
Double Conductive Shield
Do not touch.
Base
LED Indicator
Cover Fastening
Screw
Lens
Cover
Sensor
Do not touch.
[ ]
Connect tamper terminals to
a 24 hour supervisory loop.
* UL requires CX-702 to be connected to a UL listed power supply capable of providing a nominal input of 12VDC
11mA(max.) and battery standby time of 4 hours.
* For UL Listed systems, do not connect field wiring more than 25ft. to Alarm Memory, and DL terminals.
* The equipment shall be installed in accordance with the National Electrical Code,NFPA70.
When using two or more units on one wire, the
maximum length is obtained by dividing the maximum
wire length listed above by the number of units used.
Always conduct a walktest after
changing the position of this
switch to ensure the detector is
still providing optimum coverage.
CAUTION!
2. PULSE COUNT
OFF
ON
The Detection Mode can be switched to either “2” or “4” mode
depending on the environmental conditions of the installation.
POSITIVE
System Armed OPEN or +5~16VDC
NEGATIVE
0~1VDC(grounded)
0~1VDC(grounded) OPEN or +5~16VDC
System Disarmed
AM Jumper
POSITIVE : Leave AM Jumper as it is.
NEGATIVE : Cut AM Jumper as shown.
CONTROL VOLTAGE SIGNAL
1. DETERMINE THE AREA PATTERN
Before making adjustments, determine the pattern area, detection range mounting height.
The CX-702 is designed to provide ideal detection areas for different patterns ranging from 40ft.(12m) to 70ft.(21m) Wide Angle,
and 80ft.(24m) to 150ft.(45m) Long Range.
The following adjustments will provide ideal detection areas for each of these requirements.
6.ADJUSTMENTS FOR REQUIRED AREA PATTERN
2.SELECTING WIDE ANGLE OR LONG RANGE DETECTION
1. Inverting the lens will select either the Wide Angle or Long Range detection patterns.
2. Please note markings “W(Wide Angle)” and
“L(Long Range)”, on each side of lens.
3. For Wide Angle, “W” will be on top of lens.
4. For Long Range, “L” will be on top of lens.
1. LED ON / OFF
3.VERTICAL ADJUSTMENT OF DETECTION AREA
Adjust the vertical angle accrding to the desired detection range and mounting height.
1. Set the upper edge of the lens at
either the “A”, “B” or “C” position.
2. The following chart illustrates the
different position setting.
3. Confirm the detection area by
conducting a walktest.
Do not use pulse
count 4 for Long
Range detection.
CAUTION!
Check to confirm that the lens is in the
desires position.Press down the lens
holder until it clicks into place along the
guide of cover. Fix the screw at the end.
Remove the screw fixed the
lens holder(CX-702V Only),
open the cover's hook and then
lens cover can be removed.
Remove lens holder carefully.
Select wide angle or long range
according to Section 6-2. (Note:
Factory default is WIDE ANGLE.)
ft.(m)
Mounting Knockout
Pitch 3.29 inch (83.5mm)
When you remove the PCB,
push down on the hook under
PCB and remove it from its
base. Attachment of PCB is
the reverse of removal.
Power wires should not exceed the following lengths.
Guides of Lens Holder
Guides of Cover
Lens Holder
CX-702 CX-702V
WIRE SIZE 12V
1700ft.
(520m)
AWG 22 (0.33mm )2
AWG 20 (0.52mm )2
AWG 18 (0.83mm )2
14V 12V 14V
3700ft.
(1130m)
3700ft.
(360m)
2520ft.
(770m)
2690ft.
(820m)
5830ft.
(1780m)
1830ft.
(560m)
4000ft.
(1220m)
4290ft.
(1310m)
9350ft.
(2850m)
2950ft.
(900m)
6430ft.
(1960m)
HEIGHT
6 (1.8)
8 (2.4)
12 (3.6)
C
AA AB
CCC
CCC C
W : WIDE ANGLE
40 (12) 50 (15) 60 (18) 70 (21)
DISTANCE
HEIGHT
6 (1.8)
8 (2.4)
12 (3.6)
C
BA AB
CCC
CCC C
L : LONG ANGLE
80 (24) 100 (15) 120 (36) 150 (45)
DISTANCE
24
Lens
Lens Holder
TAMPER
(N.C.) ALARM
OUTPUT
(N.C.)
POWER INPUT
(9.5-16 VDC)
SPARE
D.L.
(Disable LED)
ALARM
MEMORY
TAMPER
(N.C.)
SPARE
ALARM
OUTPUT (N.C.)
POWER INPUT
(9.5-16 VDC)
LED ON / OFF Switch
Pulse Count
Selector (2 / 4)

4.INSTALLATION
5.WIRING
Loosen fastening
screw and remove
cover.
Lead in wires through knockouts
along the wiring guide on the
rear side of base. Mount base
with supplied screws. When
using a bracket, check matching
knockout position before opening
mounting holes.Wire according
to Section 5.
Conduct a walktest and
make adjustments
(Section 7). Fit cover
using fastening screw.
CX702
7.FUNCTIONS
CX-702V
Operation
If the unit triggered during armed period, when the system is
disarmed, LED will remain lit to confirm that it reported an alarm.
· Alarm Memory will operate even when LED is switched OFF.
· Alarm Memory will not operate while system is disarmed.
· After Alarm Memory latches, Alarm Output and LED operate
normaly during armed period.
Reset
Alarm Memory resets automatically
when system is re-armed.
2 : For normal applications.
4 : For use in hostile areas where there may be movement of small animals or
other objects such as fax machines or curtains.
When the “4” is selected, the detector’s sensitivity may seem sluggish. It is therefore important to always
conduct a walktest to ensure that the desired coverage is given.
Alarm Memory
This function is used to indicate if the detector was activated while the panel
was armed. It will cause the red LED on the Detector to illuminate once the
panel has been disarmed.
Compatible Control Panel is required for Alarm memory.
Connect A.M. terminal to Control Panel’s Control Voltage Signal terminal
(System Arming Status Voltage Output).
123
456
Jumper Pin Switch
The Alarm LED indicator can be switched either “ON” or “OFF”.
D.L. terminal (CX-702V Only)
LED can be enabled or disabled remotely from control panel by D.L. terminal.
1) Place Jumper Pin Switch in OFF position.
2) LED”ON” : Connect DL terminal to common ground with detector.(0~1VDC, grounded)
LED”OFF”: No Connection to the DL terminal.(OPEN or +5~16VDC)
3. ALARM MEMORY ( CX-702V Only )
3.DESCRIPTION AND OPERATION
Wiring Knockout
Terminals
Corner mount Knockout
Tamper switch
Double Conductive Shield
Do not touch.
Base
LED Indicator
Cover Fastening
Screw
Lens
Cover
Sensor
Do not touch.
[ ]
Connect tamper terminals to
a 24 hour supervisory loop.
* UL requires CX-702 to be connected to a UL listed power supply capable of providing a nominal input of 12VDC
11mA(max.) and battery standby time of 4 hours.
* For UL Listed systems, do not connect field wiring more than 25ft. to Alarm Memory, and DL terminals.
* The equipment shall be installed in accordance with the National Electrical Code,NFPA70.
When using two or more units on one wire, the
maximum length is obtained by dividing the maximum
wire length listed above by the number of units used.
Always conduct a walktest after
changing the position of this
switch to ensure the detector is
still providing optimum coverage.
CAUTION!
2. PULSE COUNT
OFF
ON
The Detection Mode can be switched to either “2” or “4” mode
depending on the environmental conditions of the installation.
POSITIVE
System Armed OPEN or +5~16VDC
NEGATIVE
0~1VDC(grounded)
0~1VDC(grounded) OPEN or +5~16VDC
System Disarmed
AM Jumper
POSITIVE : Leave AM Jumper as it is.
NEGATIVE : Cut AM Jumper as shown.
CONTROL VOLTAGE SIGNAL
1. DETERMINE THE AREA PATTERN
Before making adjustments, determine the pattern area, detection range mounting height.
The CX-702 is designed to provide ideal detection areas for different patterns ranging from 40ft.(12m) to 70ft.(21m) Wide Angle,
and 80ft.(24m) to 150ft.(45m) Long Range.
The following adjustments will provide ideal detection areas for each of these requirements.
6.ADJUSTMENTS FOR REQUIRED AREA PATTERN
2.SELECTING WIDE ANGLE OR LONG RANGE DETECTION
1. Inverting the lens will select either the Wide Angle or Long Range detection patterns.
2. Please note markings “W(Wide Angle)” and
“L(Long Range)”, on each side of lens.
3. For Wide Angle, “W” will be on top of lens.
4. For Long Range, “L” will be on top of lens.
1. LED ON / OFF
3.VERTICAL ADJUSTMENT OF DETECTION AREA
Adjust the vertical angle accrding to the desired detection range and mounting height.
1. Set the upper edge of the lens at
either the “A”, “B” or “C” position.
2. The following chart illustrates the
different position setting.
3. Confirm the detection area by
conducting a walktest.
Do not use pulse
count 4 for Long
Range detection.
CAUTION!
Check to confirm that the lens is in the
desires position.Press down the lens
holder until it clicks into place along the
guide of cover. Fix the screw at the end.
Remove the screw fixed the
lens holder(CX-702V Only),
open the cover's hook and then
lens cover can be removed.
Remove lens holder carefully.
Select wide angle or long range
according to Section 6-2. (Note:
Factory default is WIDE ANGLE.)
ft.(m)
Mounting Knockout
Pitch 3.29 inch (83.5mm)
When you remove the PCB,
push down on the hook under
PCB and remove it from its
base. Attachment of PCB is
the reverse of removal.
Power wires should not exceed the following lengths.
Guides of Lens Holder
Guides of Cover
Lens Holder
CX-702 CX-702V
WIRE SIZE 12V
1700ft.
(520m)
AWG 22 (0.33mm )2
AWG 20 (0.52mm )2
AWG 18 (0.83mm )2
14V 12V 14V
3700ft.
(1130m)
3700ft.
(360m)
2520ft.
(770m)
2690ft.
(820m)
5830ft.
(1780m)
1830ft.
(560m)
4000ft.
(1220m)
4290ft.
(1310m)
9350ft.
(2850m)
2950ft.
(900m)
6430ft.
(1960m)
HEIGHT
6 (1.8)
8 (2.4)
12 (3.6)
C
AA AB
CCC
CCC C
W : WIDE ANGLE
40 (12) 50 (15) 60 (18) 70 (21)
DISTANCE
HEIGHT
6 (1.8)
8 (2.4)
12 (3.6)
C
BA AB
CCC
CCC C
L : LONG ANGLE
80 (24) 100 (15) 120 (36) 150 (45)
DISTANCE
24
Lens
Lens Holder
TAMPER
(N.C.) ALARM
OUTPUT
(N.C.)
POWER INPUT
(9.5-16 VDC)
SPARE
D.L.
(Disable LED)
ALARM
MEMORY
TAMPER
(N.C.)
SPARE
ALARM
OUTPUT (N.C.)
POWER INPUT
(9.5-16 VDC)
LED ON / OFF Switch
Pulse Count
Selector (2 / 4)

CX-702 , CX-702V
PASSIVE INFRARED DETECTOR
CX-702 / CX-702V
- Dual Purpose Lens:Selectable ”WIDE ANGLE” and
“LONG RANGE” detection patterns
- Double Conductive Shielding of the pyroelectric element
Extremely High Light and RFI Immunity (Patent listed)
- Multifocus Optics Design (Patent listed)
- LED On/Off Switch
- Sealed Optics
- Easy Installation
FEATURES
OPTION
CA-1W : Wall Mount Bracket : adjustable ±45°(Horizontally), 0-20°(Vertically downwards)
CA-2C : Ceiling Bracket : adjustable ±45°(Horizontally), 0-20°(Vertically downwards)
1.INSTALLATION HINTS
2.DETECTION AREA
Avoid Curtain,Screen,etc.
blocking detection area.
Avoid vapor or high humidity
that can cause condensation.
Avoid direct sunlight. Do not install outdoors.Avoid mounting detector where
movement of Fans or Air
Conditioning Fans can be detected.
8.TROUBLE SHOOTING
NOTE
These units are designed to detect movement of an intruder and activate
an alarm control panel.
Being only part of a complete alarm system,we cannot accept
responsibility for any damages or other consequences resulting from an
intrusion.
These products conform to the EMC Directive 89/336 EEC.
Dimensions : inches (mm)
9.SPECIFICATIONS
CX-702V Only
- Alarm Memory
- LED Remote Control Terminal
STANDARD ALARM MEMORY
3.94(100)
5.51 (140)
2.72 (69)
No.59-0951-2 0201-29
*Specifications and design are subject to change without prior notice.
CX-702V
8mA(normal) / 16mA(max.) at 12VDC
See Section7-3.
See Section7-1.
Model
Current draw
Alarm Memory
D.L.terminal
When damage has occured to the
product, i.e. water logged, abnormal
things inside product, overheating
or smoking, strange smells etc.,
WARNING
Never repair or modify
product. It may cause
accident, fire hazard or
electric shock.
WARNING
CAUTION
Mount securely.
A falling product
may cause injury.
PROBLEM
LED does not light.
LED lights even
though no person
within area.
LED lights but
signal is not sent.
LED continues to light
PROBABLE CAUSE
Improper power supply voltage
(disconnection,low voltage).
Improper detection area.
LED switch is OFF.
Improper polarity to detector.
Moving object within area (curtain, wall hanging, etc.).
Temperature of object within area changing rapidly
(heater, air conditioning, etc.).
Relay contact is stuck or damaged due to overloading.
Faulty wiring.
Poor connection of alarm memory.
Wrong control voltage from panel.
REMEDY
Correct supply voltage to 9.5 - 16V DC.
See Section 5.
See Section 2.
Turn on the switch.
Switch positive and negative at terminal.
Remove the souces from the detection area.
Remove object from the detection area.
Check load of output.
The unit needs repair or replacement.
Wire correctly.
Reconnect wire.
Must be 0-1V DC(grounded) See Section 7-3.
1 2 3 4 5
6 7 8
*The CX-702 is UL Listed per UL639,
Intrusion-Detection Units.
*The CX-702V has not been
investigated by UL.
(CX-702 Only)
N219
**ATTENTION**
The specified detection area can be achieved by mounting the unit at a height of 8ft.(2.4m). Mounting at a lower or higher height may reduce the area of coverage.
CX-702
8mA (normal) / 11mA (max.) at 12VDC
Model
Detection method
Coverage
Detection zones
Mounting height
Sensitivity
Detectable speed
Power input
Alarm period
Alarm output
Tamper switch
Pulse count
Warm-up period
LED indicator
RF interference
Operating temperature
Environment humidity
Weight
CX-702 / CX-702V
Passive infrared
Wide Angle 85°wide Long Range
70ft. × 70ft. 150ft. × 8ft.
(21m × 21m) (45m × 2.4m)
68 zones 22 zones
5 - 12ft.(1.5 - 3.6m)
3°F at 2ft./sec., 8ft. mounting height
(1.6°C at 0.6m/sec., 2.4m mounting height)
1- 5ft. / sec. (0.3 - 1.5m/sec.)
9.5 - 16VDC
Approx. 2.5 sec.
N.C. 28VDC 0.2A max.
N.C. Opens when cover is removed.
28VDC 0.1A max.
Approx. 20 sec. 2 or 4
Approx. 1 min.
Alarm condition
No alarm 30V/m
-4°F - +122°F(-20°C - +50°C)
95% max.
7.0oz (200g)
Model
Current draw
immediately stop using product and contact your supplier.
Otherwise, continued use in such condition may cause
electric shock or fire hazard.