Optex AX-100TFR Series User manual

BATTERY OPERATED
PHOTOELECTRIC DETECTOR
BATTERY OPERATED
PHOTOELECTRIC DETECTOR
CONTENTS
1 INTRODUCTION
1-1 BEFORE YOUR OPERATION ............................... 2
1-2 PRECAUTIONS...................................................... 3
1-3 PARTS IDENTIFICATION...................................... 3
2 PREPARATIONS
2-1 ORDERING DETECTOR BATTERIES .................. 4
2-2
CHECKING THE WIRELESS TRANSMITTER SIZE ..... 4
3 INSTALLATION
3-1 WALL MOUNTING ................................................. 4
3-2 POLE MOUNTING ................................................ 6
3-3 MOUNTING IN THE BEAM TOWER...................... 7
3-4 WIRING .................................................................. 9
4 SETTING
4-1 FUNCTION........................................................... 11
4-2 4 CHANNEL BEAM FREQUENCY SELECTOR .. 11
4-3 OPTICAL ALIGNMENT ........................................ 12
4-4 BEAM INTERRUPTION ADJUSTMENT .............. 14
4-5 ADJUSTING OUTPUT ......................................... 14
5 OPERATION CHECK
5-1 LED INDICATION................................................. 14
5-2 OPERATION CHECK........................................... 14
5-3 TROUBLE SHOOTING ........................................ 15
6 OPTION...................................................................... 15
7 DIMENSIONS............................................................. 15
8 SPECIFICATIONS ..................................................... 16
INSTALLATION INSTRUCTIONS
FEATURES
No.59-2420-3 2112-08
AX-100TFR/AX-200 TFR
AX-100TFR/AX-200 TFR
• Battery-operated detector
(Batteries are not included.)
Use four LSH20 (3.6 V, 13 Ah) batteries manufactured
by SAFT.
Battery life: AX-100TFR Approximately five years
AX-200TFR Approximately three years (transmitter)
Approximately five years (receiver)
• Back box for wireless transmitters
• N.C./N.O. selection switch
• Battery saving function for wireless transmitter
• Intermittent output function
• 4 channel beam frequency selector
• International protection IP55
• LED indicator for an easy alignment
• D.Q. circuit (environmental disqualification)
• Tamper
• Beam interruption adjustment function
Model Detection range Feature
30 m / 100 ft. Battery operated with 4
selectable beam frequencies
60 m / 200 ft.
AX-100TFR
AX-200TFR
- 1 -
https://navi.optex.net/manual/08608/

Warning
Caution
This symbol indicates prohibition. The specific prohibited action is provided in and/or around the figure.
This symbol requires an action or gives an instruction.
Do not use the product for purposes other than the detection of moving objects such as people and vehicles.
Do not use the product to activate a shutter, etc., which may cause an accident.
Never attempt to disassemble or repair the product. It may cause fire or damage to the devices.
Do not use batteries other than those specified.
Specified batteries: Four LSH20 batteries manufactured by SAFT
Do not use batteries that have different levels of power remaining (i.e., new and used batteries).
Not observing the above may result in an explosion, leakage of electrolyte, emission of toxic gases or other
outcomes that may be harmful to people and property.
[Handling of Batteries]
Fire, explosion and severe burn hazard. Do not recharge, short circuit, crush, disassemble, heat above
100°C (212°F), incinerate, or expose contents to water.
Do not solder directly to the cell.
Do not pour water over the product with a bucket, hose, etc. The water may enter, which may cause damage to the
devices.
Clean and check the product periodically for safe use. If any problem is found, do not attempt to use the
product as it is and have the product repaired by a professional engineer or electrician.
Do not touch the unit base or power terminals of the product with a wet hand (do not touch when the
product is wet with rain, etc.). It may cause electric shock.
Warning
Caution
Failure to follow the instructions provided with this indication and improper handling may cause
death or serious injury.
Failure to follow the instructions provided with this indication and improper handling may cause
injury and/or property damage.
1INTRODUCTION
1-1 BEFORE YOUR OPERATION
•Read this instruction carefully prior to installation.
•After reading, store this instruction carefully in an easily accessible place for reference.
•This instruction uses the following warning indications for correct use of the product, harm to you or other people
and damage to your assets, which are described below. Be sure to understand the description before reading the
rest of this instruction.
- 2 -

1-3 PARTS IDENTIFICATION
ChassisBack boxMain unitCover
Back box lock screw
Harness retainer plate
Cover lock screw Velcro tape: 2 setsU-brackets: 2
Mounting plate
lock screws
Pole mounting
bracket set
Pole mounting
brackets: 6
M3×8
screws: 6
M4×20
screws: 4
M4×30
screws: 4
2
1
2
1
3
Loosen the
back box lock screw.
Pull
Press Loosen the
cover lock screw.
Pull
Removing the Back Box >> Removing the Cover >>
1-2 PRECAUTIONS
Install the unit on a stable
surface.
Install the pole in a location
where sufficient stability
can be ensured.
Do not install the unit in a
location where trees,
leaves, or other objects
that may swing in the wind
may block the beam.
Do not install the receiver
in a location where it is
exposed to direct sunlight.
Receiver
Transmitter
(different
model)
Transmitter
Do not allow the infrared
beam from a different model
to reach the receiver.
Install the unit more than 1
m (3.3 ft.) away from the
wall or fence that are
running parallel to the beam.
This symbol indicates prohibition. This symbol indicates recommendation.
AX-100TFR
Detection range: 30 m (100 ft.)
AX-200TFR
Detection range: 60 m (200 ft.)
Installation
Height
0.7 m - 1 m
(2.3 ft. - 3.3 ft.)
Observe the prescribed
transmitter-receiver
distance (range) and
installation height.
The pole size should be
43 - 48 mm
( 1.69" - 1.89").
1 m (3.3 ft.)
Accessories
- 3 -

1Remove the chassis from the back box. 2Fix the chassis to the wall.
3INSTALLATION
3-1 WALL MOUNTING
Wall mounting screws
(M4×20, supplied)
Caution
After mounting the chassis, wiggle the tamper
bushing with your thumb and forefinger to ensure
the tamper works properly.
2PREPARATIONS
2-1 ORDERING DETECTOR BATTERIES
Specified batteries: Four LSH20 batteries manufactured by SAFT
For information about batteries, visit the following website and contact your local SAFT sales representative.
http://www.saftbatteries.com/battery-search/ls-lsh/
2-2 CHECKING THE WIRELESS TRANSMITTER SIZE
Use two wireless transmitters for the each of receivers and transmitters. When wireless transmitters with two or
more inputs are available, use one wireless transmitter for the each of transmitters and receivers.
The following figure shows the dimensions of the wireless transmitter installation space in the back box. Note that
transmitters with dimensions greater than those are not applicable.
42.5 (1.67)
42.5 (1.67)
26.5 (1.04)
26.5
(1.04)
78 (3.07)
78 (3.07)
66 (2.60)
154 (6.06)
154 (6.06)
Unit: mm (inch)
• Be sure to monitor the alarm and low
battery outputs.
• To monitor the tamper output, include
a wireless transmitter supporting three
or more inputs into the system.
Note>>
- 4 -

3Connect the cables from the back box to the
wireless transmitters.
4Insert the specified batteries into the back box.
5Fix the wireless transmitters in the back box. 6Run the cables so that they are not pinched
between the chassis and back box.
Receiver-Wireless Transmitter Connection
Yellow/Yellow-white cable: For alarm
Green/Green-white cable: For low battery
Black/Black-white cable: For tamper
Transmitter-Wireless Transmitter Connection
Green/Green-white cable: For low battery
Black/Black-white cable: For tamper
Caution
• When N.O. wireless transmitters are used, see
“Using the N.O. type transmitter” in sec. “3-4” to
change the wiring.
• Use the specified batteries for the wireless
transmitters.
Warning
• Do not use batteries other than those specified.
Specified batteries:
Four LSH20 batteries manufactured by SAFT
• Do not mix batteries that have different levels of
power remaining (i.e., new and used batteries).
Not observing the above may result in an explosion,
leakage of electrolyte, emission of toxic gases or
other outcomes that may be harmful to people and
property.
Caution
Remove all batteries prior to replacing with new ones.
If this is not followed, the low battery indicator LED
will not reset and continue to flicker.
Cut the supplied Velcro tape
to an appropriate length and apply.
Specified batteries
SAFT LSH20
3.6 V 13 Ah
7Install the back box onto the chassis.
Tighten the
back box lock screw.
Lithium batteries are used.
Follow EU Battery Directive (2013/56/EU)
to dispose batteries.
- 5 -

1Remove the chassis from the back box.
5Take steps 3 through 6 refer to sec. “3-1” to
install the wireless transmitters and batteries in
the back box, and then install the back box on
the chassis.
3-2 POLE MOUNTING
2Using a screwdriver or similar tool, break the
knockout portion as shown.
1Remove the chassis from the back box.
2Using a screwdriver or similar tool, break the
knockout portion as shown.
3Install three pole mounting brackets on the chassis.
4Fix the chassis on the pole.
Caution
After mounting the chassis, wiggle the tamper
bushing with your thumb and forefinger to ensure the
tamper works properly.
-Single set
-Two detectors in opposing directions
Tighten the
back box lock screw.
Choose
a different
pair of
knockouts.
Detector 1 Detector 2
3Install three pole mounting brackets on the chassis.
Install the bracket
in the knocked-out
locations in step 2 .
Pole mounting
bracket
(supplied)
M3×8 screw
(supplied)
Pole mounting
bracket (supplied)
M3×8 screw
(supplied)
Detector 1 Detector 2
Knockout two
locations pairing
in a horizontal line.
Install the bracket
in the knocked-out
locations in step 2 .
Pole mounting bracket
(supplied)
M3×8 screw
(supplied)
U-bracket
(supplied)
M4×30 screw
(supplied)
- 6 -

5
1Remove the cover from the detector.
4Fix the chassis on the pole.
Caution
After mounting the chassis, wiggle the tamper
bushing with your thumb and forefinger to ensure the
tamper works properly.
Caution
Cables are connected between the back box and the
main unit. Do not exert an excessive amount of force
on the cables. Handle the main unit with care.
2Loosen the main unit fixing screw and remove the
main unit from the back box.
Loosen the main unit
fixing screw.
3Remove the harness retainer plate.
Main unit
Harness retainer
plate (sticker)
Tighten the
back box lock screw.
U-bracket
(supplied)
M4×30 screw
(supplied)
M4×30
screw
(supplied)
Detector 1
Detector 2
3-3 MOUNTING IN THE BEAM TOWER
Mounting inside optional beam tower.
- 7 -

4Open the wiring hole in
the top of the main unit
using pliers.
6Fix the chassis and main unit mounting bracket
(optional) in the tower.
5Remove the chassis from
the back box.
Loosen the
back box lock screw.
Wiring hole
Main unit mounting
bracket
(option: MP-4)
Caution
After mounting the chassis, wiggle the tamper
bushing with your thumb and forefinger to ensure
the tamper works properly.
250 mm (9.8 inch) or less
7Refer to sec. “3-1” steps 3 through 6 to install
the wireless transmitters and batteries in the
back box, and then install the back box on the
chassis. Install the main unit on the main unit
mounting bracket.
Tighten the screws.
8After completing the settings and operation check,
insert the tamper bushing into each transmitter/receiver.
Tamper bushing
(option: MP-4)
Insert a flat-blade
screwdriver, and twist it
CLOCKWISE and
slightly to remove the
tamper bushing.
How to remove the tamper bushing >>
Caution
• The switch selection is not recognized with the
tamper bushing inserted.
Remove the tamper bushing before selecting a
function using the switch.
• After completing the settings, be sure to insert the
tamper bushing to check that all LEDs are OFF.
Without the tamper busing, the LEDs are kept ON,
which consumes more battery power.
• Monitor Jack Output become disable when tamper
bushing inserted.
• When inserting the tamper bushing, the beam
alignment test point will be disabled. Please
complete the alignment procedure before inserting
tamper bushing.
- 8 -

3-4 WIRING
-Using the N.C. type transmitter
This product is provided with wiring based on the assumption that N.C. wireless transmitters are used.
Connect the cables from the receiver and the back box to the respective terminals on the wireless transmitters.
• To monitor some or all of "low battery", "D.Q." and "tamper outputs", use wireless transmitters supporting number of
inputs required into the system.
• Refer to the information about the "D.Q. output" on the next page.
Note>>
Transmitter
AX-100/200TFR
Transmitter
AX-100/200TFR (BE)
Receiver
+ –
NC
COM
NO
POWER
+ NC
COM NO NC
COM NONC/NO NC/NO
POWER LB TAMPER
Back box
Wireless transmitter
ALARM DQ
–
TAMPER
+ –
R
R/W
Y
Y/W
B
B
B/W
G
G/W
Bu
Bu/W
RW
Alarm
Low battery
Tamper
Power
Trouble
Color keys>>
Red
Red & White
Yellow
Yellow & White
Green
Green & White
Blue
Blue & White
R
Y
G
Bu
Black
Black & White
B
B/W
R/W
Y/W
G/W
Bu/W
WWhite
+ –
SP SP
NC/NO
POWER
SP SP
LB
Wireless transmitter
+ –
NC
COM
NO
POWER TAMPER
+ –
Back box
R
R/W
RB
B
B/W
G
G/W
W
Low battery
Tamper
Power
NC
COM
NO
+ –
SP SP
NC/NO
TAMPER
POWER
SP SP
LB
Wireless transmitter
+ –
NC
COM
NO
POWER TAMPER
+ –
Back box
R
R/W
RB
B
B/W
G
G/W
W
Low battery
Tamper
Power
- 9 -

-Using the N.O. type transmitter
When N.O. wireless transmitters are
used, change the wiring and switch
settings from initial setting.
Exchange the connections.
Cut the wires and connect to two terminals.
Turn ON switch No. 5 of Receiver
and No.3 of Transmitter.
Transmitter
AX-100/200TFR
Transmitter
AX-100/
200TFR (BE)
D.Q. will send a trouble signal when the beam strength is below acceptable levels, for more than 20 seconds, due
to rain, snow, or heavy fog.
- D.Q. output (environmental disqualification)
20 sec. 2 sec.
ON
OFF
Reception level
Adverse weather
level
Alarm output level
D.Q. output
Operating Time Chart
Receiver
+ –
NC COM NO
POWER
+ NC
COM NO NC
COM NONC/NO NC/NO
POWER LB TAMPER
Back box
Wireless transmitter
ALARM DQ
–
TAMPER
+ –
R
R/W
Y
Y/W
B
G
G/W
Bu
Bu/W
R
ON
BB/W
B/W
W
Alarm
Low battery
Tamper
Power
Trouble
Color keys>>
Red
Red & White
Yellow
Yellow & White
Green
Green & White
Blue
Blue & White
R
Y
G
Bu
Black
Black & White
B
B/W
R/W
Y/W
G/W
Bu/W
WWhite
+ –
SP SP
NC/NO
POWER
SP SP
LB
Wireless transmitter
+ –
NC
COM
NO
POWER TAMPER
+ –
Back box
R
R/W
RB
G
G/W
ON
B/W
B
W
Low battery
Tamper
Power
NC
COM
NO
+ –
SP SP
NC/NO
TAMPER
POWER
SP SP
LB
Wireless transmitter
+ –
NC
COM
NO
POWER TAMPER
+ –
Back box
R
R/W
RB
G
G/W
ON
B/W
B/W
BW
Low battery
Tamper
Power
- 10 -