ORiNG IAP-620 Series User manual

Features
High Speed Air Connectivity: WLAN interface support up to 300Mbps
link speed
Highly Security Capability: WEP/WPA/WPA-PSK(TKIP,AES)/
WPA2/WPA2-PSK(TKIP,AES)/802.1X Authentication supported
Support X-Roaming < 100 ms
Support wireless load balance
Support AP/Client/Bridge/AP-Client Mode
Switch Mode Supported: Daisy Chain support to reduce usage of
switch ports
Dual redundant Ethernet port support redundant mode (Recovery
time < 10ms)
Secured Management by HTTPs
Fully Compliant with IEEE802.3af (Power Device at ETH2, PoE Models)
Wireless connecting status monitoring
Event Warning by Syslog, Email, SNMP Trap, Relay output and Beeper
1KV isolation for PoE P.D. port of IAP-620+
Rigid IP-30 housing design
DIN-Rail and Wall-mount enabled
are reliable 802.11 a/b/g/n WLAN Access
Point with 2 ports LAN. It supports 802.1X and MAC filters for security
control. It can be configured to operate in AP/Bridge/Repeater/AP-
Client mode. You are able to configure by
WEB interface via LAN port or WLAN interface.
provide dual Ethernet ports in switch mode, so that you can
use Daisy Chain to reduce the usage of Ethernet switch ports. In
addition, also provides P.D. feature on ETH2 which is fully
compliant with IEEE802.3af PoE P.D. specification. Therefore,
are one of the best communication solutions for
wireless applications on the industrial network.
IAP-620 / IAP-620+ series
IAP-620 / IAP-620+ series
IAP-620 / IAP-620+
series
IAP-620+
IAP-620
/ IAP-620+ series
IAP-620/IAP-620+ can also be configure through ORing’s Windows utility
Open-Vision
Step 1: Open the commander and click ”Discover”, the AP devices will
show on the list.
Step 2: Choose your access point, and it will show the AP function tree.
Simultaneity, you can login and then set the AP.
Introduction
Open-Vision
QIG
Version 1.1
Quick Installation Guide
ORing Industrial Networking Corp.
Quick Installation Guide
IAP-620 Series
Wireless
IAP-620 Series
Industrial Wireless LAN Access
Point
ACCESS POINT
INDUSTRIAL
1907-2-29-IAP620-0
Specifications
ORing WLAN Access Point
Model IAP-620
Physical Ports
WLAN Interface
Power Indicator
Faul t RedforEthernetlinkdownorpowerdownindicator
10/100Base-T(X) RJ45 port
indicator GreenforportLink/Actat100Mbps. AmberforportLink/Actat10Mbps.
Power
Redundant Input power
Power consumption(Typ.)
Dual DC inputs. 12~48VDC on 6-pin terminal block
6Watts
Overload current protection
Reverse polarity protection Present
Present
Physical Characteristic
Enclosure IP-30
Dimension(WxDxH) 54.1(W) x 106.1(D) x 145.4(H) mm (2.13 x 4.18 x 5.72 inch.)
Weig ht (g ) 800 g
Environmental
-40to85C(-40to185F)
oo
Storage Temperature
10/100Base-T(X) Ports in RJ45
Auto MDI/MDIX 2
LED Indicators
AP/Client/Bridge/AP-Client
Operating Mode
IEEE802.11a/n: OFDM with BPSK, QPSK, 16QAM, 64QAM
IEEE802.11b: CCK, DQPSK, DBPSK
IEEE802.11g/n: OFDM with BPSK, QPSK, 16QAM, 64QAM
Modulation
802.11b: 1/2/5.5/11 Mbps;
802.11a/g: 6/9/12/18/24/36/48/54 Mbps
802.11n(40MHz): UP to 300 Mbps
Transmission Rate
802.11a: 13dBm 1.5dBm
802.11b: 16dBm 1.5dBm
802.11g: 14dBm 1.5dBm
802.11n(2.4G@20MHz): 13dBm 1.5dBm
802.11n(2.4G@40MHz): 12dBm 1.5dBm
802.11n(5G@20MHz): 12dBm 1.5dBm
802.11n(5G@40MHz): 12dBm 1.5dBm
±
±
±
±
±
±
±
Transmit Power
802.11a: -68dBm 2dBm@54Mbps
802.11b: -82dBm 2dBm@11Mbps
802.11g: -68dBm 2dBm@54Mbps
802.11n(2.4G@20MHz, MCS15): -64dBm 2dBm
802.11n(2.4G@40MHz, MCS15): -60dBm 2dBm
802.11n(5G@20MHz, MCS15): -64dBm 2dBm
802.11n(5G@40MHz, MCs15): -60dBm 2dBm
±
±
±
±
±
±
±
Receiver Sensitivity
2 x External reverse SMA type antenna connector
Antenna Connector
America/FCC:
2.412~2.462 GHz (11 channels)
5.180~5.240 GHz & 5.745~5.825 GHz (9 channels)
Europe CE/ETSI:
2.412~2.472 GHz (13 channels)
5.180~5.240 GHz (4 channels)
Japan(JP):
2.412~2.484 GHz (13 Channels)
5.180~5.240 GHz (4 channels)
Canada(CA):
2.412~2.462 GHz (11 channels)
5.180~5.240 GHz & 5.745~5.825 GHz (9 channel)
Frequency Band
SSID broadcast disable
WEP: (64-bit ,128-bit key supported)
WPA:
WPA2 :802.11i(WEP and AES encryption)
WPA-PSK (256-bit key pre-shared key supported)
802.1X Authentication supported
TKIP encryption
Encryption Security
Wireless Security
IAP-620+
PoE P.D Port
Present at ETH2
Fully compliant with IEEE 802.3af Power
Device specification
Over load & short circuit protection
Isolation Voltage: 1000 VDC min.
Isolation Resistance: 10 ohms min
8
ARP,BOOTP, DHCP, DNS, HTTP, IP, ICMP, SNTP, TCP, UDP, RADIUS, SNMP, STP (IEEE 802.1D)
Protocol
Protocol Support
WLAN LED WLAN Link /ACT: Green: Link, Orange : Poor signal
Green for WLAN Strength: 1<25%, 2<50%, 3<75%, 4<100%
804 g
-10to60C(-14to140F)
oo
Operating Temperature
5% to 95% Non-condensing
Operating Humidity
Regulatory Approvals
FCC Part 15, CISPR (EN55022) class A
EMI
EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge), EN1000-4-6(CS),
EN61000-4-8, EN61000-4-11
EMS
IEC60068-2-27
Shock
IEC60068-2-32
IEC60068-2-6
Vibration
EN60950-1
Safety
Free Fall
Warranty
3years
Fault contact
Relay Relayoutputtocarrycapacityof1Aat24VDC
PWR 1(2)(PoE) / Ready:
RedOn:Powerisonandbootingup.
Green On: Power is on and functioning Normally.
Installation
DIN-Rail Install Step Wall-mounted Install Step
ORing Industrial Networking Corp.
Copyright© 2012 ORing
All rights reserved.
TEL: [phone]
FAX: [phone]
Website: www.oring-networking.com
E-mail: [email protected]
PRINTED ON RECYCLED PAPER

IAP-620+IAP-620
Front Panel
Packing list
Accessory
Ethernet Port 1
Ethernet Port 2
Wireless LAN LED
Wall-mounted kit DIN-Rail kit
1
6-Pin Terminal block
2
4
Screw (M3 X5)
3
Dust Cover
5CD
6
QIG
7
Industrial IEEE 802.11 a b g n wireless access point
with 2x10/100Base-T(X), US band
///
IAP-620_US
Model name Description Accessory
100M LNK/ACT LED
(Green)
10M LNK/ACT LED
(Amber)
Quick Installation Guide
ORing Industrial Networking Corp.
Front Panel
A
B
IAP-620_EU
IAP-620_JP
IAP-620_CA
1X1, 2X1, 3X6,
5X2, 6X1, 7X1,
4X1,
8X2
Quick Installation Guide
IAP-620/620+
WLAN
Fault
PWR2
PWR1
ANT.1
ETH1
ETH2
WLAN
Fault
PWR2
PWR1
ANT.1
ETH1
ETH2
P.O.E.
P.O.E.
BA
WLAN Antenna
8
PRINTED ON RECYCLED PAPER
QIG
WLAN Antenna
Power 1 LED
Power 2 LED
Fault LED
ANT.2
WLAN Strength LED
ANT.2
Version 1.1
IAP-620 Series
Wireless
IAP-620 Series
Industrial Wireless LAN Access
Point
ACCESS POINT
INDUSTRIAL
Power Connection Guide
Reset
PWR-2 PWR-1
V2+ V2- Relay V1+ V1-
Reset Button
Terminal Block Power-2 Input
Relay Output Pin
Terminal Block Power-1 Input
Applications
In practical operation of wireless access point, Windows utility (Open-Vision) is
supported. This utility is very helpful for you to search and configure IP of
access point on the industrial network. In addition, the wireless access point
support various kinds of operation modes include AP/ Bridge/Repeater/AP-
Client mode. IAP-620 / IAP-620+ series also support PoE P.D. feature to
extend the layout up to 100 meters. You can build up the wireless network
easily.
Various kinds of operation modes
1X1, 2X1, 3X6,
5X2, 6X1, 7X1,
4X1,
8X2
1X1, 2X1, 3X6,
5X2, 6X1, 7X1,
4X1,
8X2
1X1, 2X1, 3X6,
5X2, 6X1, 7X1,
4X1,
8X2
1X1, 2X1, 3X6,
5X2, 6X1, 7X1,
4X1,
8X2
1X1, 2X1, 3X6,
5X2, 6X1, 7X1,
4X1,
8X2
1X1, 2X1, 3X6,
5X2, 6X1, 7X1,
4X1,
8X2
1X1, 2X1, 3X6,
5X2, 6X1, 7X1,
4X1,
8X2
Industrial IEEE 802.11 a b g n wireless access point
with 2x10/100Base-T(X), EU band
///
Industrial IEEE 802.11 a b g n wireless access point
with 2x10/100Base-T(X), JP band
///
Industrial IEEE 802.11 a b g n wireless access point
with 2x10/100Base-T(X), CA band
///
A
A
A
IAP-620+_US
IAP-620+_EU
IAP-620+_JP
IAP-620+_CA
B
B
B
Iindustrial IEEE 802.11 a b g n wireless access point
with x Base T X port PoE P D US band
///
2 10/100 - ( ), 1- . .,
Iindustrial IEEE 802.11 a b g n wireless access point
with x Base T X port PoE P D band
///
2 10/100 - ( ), 1- . ., EU
Iindustrial IEEE 802.11 a b g n wireless access point
with x Base T X port PoE P D JP band
///
2 10/100 - ( ), 1- . .,
Iindustrial IEEE 802.11 a b g n wireless access point
with x Base T X port PoE P D band
///
2 10/100 - ( ), 1- . ., CA