ORiNG IGR-20 Series User manual

I
IG GR R- -2 20 0 s se er ri ie es s
U
Us se er r’ ’s s M Ma an nu ua al l
V
Ve er rs si io on n 1 1. .0 0
N
No ov v, , 2 20 01 13 3
w
ww ww w. .o or ri in ng g- -n ne et tw wo or rk ki in ng g. .c co om m

COPYRIGHT NOTICE
Copyright © 2012ORing Industrial Networking Corp.
All rights reserved.
No part of this publication may be reproduced in any form without the prior written consent of
ORing Industrial Networking Corp.
TRADEMARKS
is a registered trademark of ORing Industrial Networking Corp.
All other trademarks belong to their respective owners.
REGULATORY COMPLIANCE STATEMENT
Product(s) associated with this publication complies/comply with all applicable regulations.
Please refer to the Technical Specifications section for more details.
WARRANTY
ORing warrants that all ORing products are free from defects in material and workmanship for a
specified warranty period from the invoice date (5 years for most products). ORing will repair or
replace products found by ORing to be defective within this warranty period, with shipment
expenses apportioned by ORing and the distributor. This warranty does not cover product
modifications or repairs done by persons other than ORing-approved personnel, and this
warranty does not apply to ORing products that are misused, abused, improperly installed, or
damaged by accidents.
Please refer to the Technical Specifications section for the actual warranty period(s) of the
product(s) associated with this publication.
DISCLAIMER
Information in this publication is intended to be accurate. ORing shall not be responsible for its
use or infringements on third-parties as a result of its use. There may occasionally be
unintentional errors on this publication. ORing reserves the right to revise the contents of this
publication without notice.
CONTACT INFORMATION
ORing Industrial Networking Corp.
3F., No.542-2, JhongJheng Rd., Sindian District, New Taipei City 23148, Taiwan (R.O.C.)
Tel: [phone] // Fax: [phone]
Website: www.oring-networking.com
Technical Support
E-mail: [e-mail]
Sales Contact
E-mail: [e-mail] (Headquarters)
[e-mail] (China)

Tables of Content
Getting to Know your Router .......................................................................1
1.1 Overview..........................................................................................................................1
1.2 Software Features...........................................................................................................1
1.3 Hardware Features..........................................................................................................1
Hardware Installation....................................................................................2
2.1 Installation Router on DIN-Rail.......................................................................................2
2.2 Wall Mounting Installation...............................................................................................3
Hardware Overview.......................................................................................5
3.1 Front Panel.......................................................................................................................5
3.2 Front Panel LEDs............................................................................................................6
Cables.............................................................................................................6
4.1 Ethernet Cables...............................................................................................................6
Management Interface...................................................................................7
5.1 First-time Installation.......................................................................................................7
5.2 Configure the Router.......................................................................................................9
5.3 Main Interface................................................................................................................10
5.3.1 Basic Setting................................................................................................................11
WAN....................................................................................................................................11
LAN.....................................................................................................................................13
DHCP...................................................................................................................................13
DDNS ..................................................................................................................................15
Date&Time...........................................................................................................................15
5.3.2 Networking Setting......................................................................................................17
NAT Setting..........................................................................................................................17
Firewall Setting ....................................................................................................................19
VPN Setting .........................................................................................................................21
VRRP...................................................................................................................................28
Routing Protocol (Routing Setting) .......................................................................................28
5.3.3 System Tools ...............................................................................................................32
Login Setting........................................................................................................................32
Router Restart.......................................................................................................................33
Firmware Upgrade................................................................................................................33
Save/Restore Configurations.................................................................................................34
Miscellaneous (Ping) ............................................................................................................35
Even warning setting.............................................................................................................36
DIDO ...................................................................................................................................40

5.3.4 System Status ..............................................................................................................40
System Info ..........................................................................................................................40
System Log...........................................................................................................................41
Traffic Statistics....................................................................................................................41
Technical Specifications.............................................................................42
Compliance..................................................................................................43

IGR-20 Series User’s Manual
ORing Industrial Networking Corp. 1
Getting to Know your Router
1.1 Overview
The ORing IGR-20 is designed to operate in industrial environment. The router
provides a fast and effective ways of communicating to the internet over wired LAN. In
addition, multiple types of WAN connection are provided for easily access to the internet.
The ORing IGR-20 router's VPN capability creates encrypted "Virtual Tunnels" through
the internet, allowing remote or traveling users for secured connection with the network in
your office.
1.2 Software Features
Intuitive Web-based management user interface for simply and easily operation.
Functions of firewall provides many security features such as blocking attacks from
hacker, especially IP Spoofing, Ping flood, Ping of Death, DOS, DRDOS, Stealth Scan,
ICMP flooding etc.
Advanced firewall configuration to extend the capability and security, such as Virtual
Server, Port Trigger, DMZ host, UPnP auto Forwarding, IP Filter and MAC filter.
1.3 Hardware Features
Two 10/100/1000 Base-T(X) Ethernet ports for WAN / LAN connection individually.
Fully Compliant with IEEE802.3af (Power Device at ETH2, WAN port) only for IGR-20+
Redundant Power Inputs: 12~48 VDC on terminal block
Casing: IP-30
Dimensions(W x D x H) : 74.3(W) x 109.2(D) x 153.6(H) mm
Storage Temperature: -40 to 85oC
Operating Humidity: 5% to 95%, non-condensing

IGR-20 Series User’s Manual
ORing Industrial Networking Corp. 2
Hardware Installation
2.1 Installation Router on DIN-Rail
Each router has a DIN-Rail kit on rear panel. The DIN-Rail kit helps router to fix on the
DIN-Rail.
Step 1: Slant the router and mount the metal spring to DIN-Rail.
Step 2: Push the router toward the DIN-Rail until you heard a “click” sound.

IGR-20 Series User’s Manual
ORing Industrial Networking Corp. 3
2.2 Wall Mounting Installation
Each router has another installation method to fix the router. A wall mount panel can
be found in the package. The following steps show how to mount the router on the wall:
Step 1: Remove DIN-Rail kit.
Step 2: Use 6 screws that can be found in the package to combine the wall mount panel.
Just like the picture shows below:

IGR-20 Series User’s Manual
ORing Industrial Networking Corp. 4
The screws specification shows in the following two pictures. In order to prevent the
routers from any damage, the screws should not larger than the size that used in IGR-20
series.
Pozidrive
Step 3: Mount the combined on the wall.

IGR-20 Series User’s Manual
ORing Industrial Networking Corp. 5
Hardware Overview
3.1 Front Panel
The following table describes the labels that stick on the IGR-20.
Port
Description
10/100/1000
Base-T(X) fast
Ethernet ports
10/100/1000Base-T(X) RJ-45 fast Ethernet ports support
auto-negotiation.
Default Setting :
Speed: auto
Duplex: auto
PoE PD Port
ETH2 (WAN port) of IGR-20+ compliant with IEEE802.3af PoE
specifications and can be connected to PoE switches.*
*Note: Please refer to the products of ORing IPS series for P.O.E. Ethernet switch.

IGR-20 Series User’s Manual
ORing Industrial Networking Corp. 6
3.2 Front Panel LEDs
LED
Color
Status
Description
PWR1
Green
Green On
DC power 1 activated.
PWR2
Green
Green On
DC power 2 activated.
ETH1
Green/Amber
On
Port link up at 10Mbps /1000Mbps.
Green
On
Port link up at 100Mbps.
Blinking
Data transmitted.
ETH2
Green/Amber
On
Port link up at 10Mbps/1000Mbps.
Green
On
Port link up at 100Mbps.
Blinking
Data transmitted.
Blinking
WLAN Data transmitted.
WAN
Green
On
Modem Ready
Fault
Red
On
Fault relay. Power failure or Port
down/fail.
Cables
4.1 Ethernet Cables
The IGR-20 WLAN AP has two 10/100/1000 Base-T(X) Ethernet ports. According to
the link type, the AP use CAT 3, 4, 5, 5e, 6 UTP cables to connect to any other network
device (PCs, servers, switches, routers, or hubs). Please refer to the following table for
cable specifications.
Cable Types and Specifications
Cable
Type
Max. Length
Connector
10Base-T
Cat. 3, 4, 5 100-ohm
UTP 100 m (328 ft)
RJ45
100Base-T(X)
Cat. 5 100-ohm UTP
UTP 100 m (328 ft)
RJ45
1000Base-T(X)
Cat 5e,6
UTP 100 m (328 ft)
RJ45

IGR-20 Series User’s Manual
ORing Industrial Networking Corp. 7
Management Interface
5.1 First-time Installation
Before installing IGR-20, you need to access router by a computer equipped with an
Ethernet card.
Basic connection for IGR-20
Step 1: Select the Power Source
IGR-20 router can be powered by +12~48V DC power input, or by P.O.E. (Power over
Ethernet) PSE Ethernet switch.
Step 2: Connect a computer to IGR-20
Use either a straight-through Ethernet cable or cross-over cable to connect to ETH1 of
IGR-20 AP router to a computer. If the LED of the LAN port lights up, it indicates the
connection is established. After that, the computer will initiate a DHCP request to get an
IP address from the router.
Step 3: Use the web-based manager to configure IGR-20
The default gateway IP of IGR-20 router is 192.168.10.1. Start the web browser of
your computer and type http://192.168.10.1 in the address box to access the webpage. A
login window will popup, and then enter the default login name admin and password
admin.

IGR-20 Series User’s Manual
ORing Industrial Networking Corp. 8
Login screen
Step 4: Select WAN connection type
Click the Basic Setting in the top menu to enter the WAN configuration page, select the
proper connection type according to the information of your ISP. If you use modem/3G as
WAN connection
WAN connection type

IGR-20 Series User’s Manual
ORing Industrial Networking Corp. 9
Step 6: Review the router settings and check router status
Click the System Status in the top of the menu, the system info page will be shown.
You can check all the configuration and status of the router.
System status Screen
5.2 Configure the Router
In this section, the web management page will be explained in detail.
By default setting, you can type http://192.168.10.1 in the address box of web browser
to login the web management interface. Alogin window will be prompted, enter username
admin & password admin to login.
Login screen
For security reasons, we strongly recommend you to change the password. Click on
System Tools > Login Setting and change the password.

IGR-20 Series User’s Manual
ORing Industrial Networking Corp. 10
5.3 Main Interface
The Home screen will be shown when login successfully.
Main Interface
In the page, you can check the Firmware version, the router running time and the WAN
IP setting.
The following table describes the labels in this screen.
Label
Description
Firmware
Show the current firmware version.
Uptime
Show the elapsed time since theAP router is started.
Wan IP
Show the WAN IP address.

IGR-20 Series User’s Manual
ORing Industrial Networking Corp. 11
5.3.1 Basic Setting
WAN
The IGR-20 provides 2 types of WAN connection.
1. WAN Connection Type: Dynamic/Static IP
Dynamic/Static IP
The following table describes the labels in this screen.
Label
Description
Obtain an IP address
automatically
Select this option if you would like to have an IPaddress assigned
automatically from the WAN port by DHCP server in your network.
Use the following IP
address
Select this option if you would like to assign an IP address to the
WAN port manually. You should set the IP Address, Subnet Mask
and Default gateway appropriately so that they comply with IP
rules.
Obtain DNS server
address
automatically
Obtain DNS server from DHCP server. If the above Obtain an
IP address automatically is selected, this option will be chosen
accordingly.
Use the following
DNS server
addresses
Specify DNS server address manually.

IGR-20 Series User’s Manual
ORing Industrial Networking Corp. 12
2. WAN Connection Type: PPPoE
PPPoE Screen.
The following table describes the labels in this screen.
Label
Description
User Name /
Password
Enter the username & password provided by your Internet
Service Provider (ISP).
Service Name
Enter the service name provided by your ISP.
AC Name
Enter the name of the access concentrator as provided by your
ISP.
Specify the IP & DNS
provided by ISP
Enter static IP and DNS address which may required by some ISP
Connection Mode
Auto: Connect automatically when the router boots up.
Connect on Demand: Select to disconnect the PPP session if
the router has had no traffic for the specified amount of time.
Enter the Max Idle Time in minutes.
Manual: Select this option to use only the Connect/Disconnect
buttons to call up or close the connection.

IGR-20 Series User’s Manual
ORing Industrial Networking Corp. 13
LAN These are the IP settings of the LAN interface for the IGR-20. The LAN IP
address is privately for your internal network and can not be exposed on the
Internet.
LAN Screen
The following table describes the labels in this screen.
Label
Description
IP Address
The IP address of the LAN interface, the default IP address is
192.168.10.1
Subnet Mask
The Subnet Mask of the LAN interface, the default Subnet mask
is 255.255.255.0
DHCP
DHCP stands for Dynamic Host Control Protocol. The IGR-20 with a built-in
DHCP server. The internal DHCP server will assign an IP address to the computers
(DHCP client) on the LAN automatically.
Set your computers to be DHCP clients by setting their TCP/IP settings to Obtain
an IP Address Automatically. The DHCP server will allocate an unused IP address
from the IP address pool to the requesting computer automatically.
The IP Allocation provides one-to-one mapping of MAC address to IP address.
When a computer with the MAC address requesting an IP from the IGR-20 , it will be
assigned with the IP address according to the mapping. You can choose one from the
client lists and add it to the mapping relationship.

IGR-20 Series User’s Manual
ORing Industrial Networking Corp. 14
1. DHCP Sever
DHCP Server Screen
The following table describes the labels in this screen.
Label
Description
DHCP Mode
Select built-in DHCP server or DHCP Forwarder
DHCP Server
Enable or Disable the DHCP Server. The default setting is
Enable
Starting IP
The starting IP address of the IP range for the DHCP server
Ending IP
The ending IP address of the IP range for the DHCP server
Lease Time
The period of time for the IPto be leased. Enter the Lease time.
The default setting is 48 hours.
Local Domain Name
Enter the local domain name of private network. It is optional.
DNS Server 1&2
Enter the DNS Server. It is optional.
WINS Server
Enter the WINS Server. It is optional.
DHCP Relay start IP
Enter DHCP Relay starting IP
DHCP Relay end IP
Enter DHCP Relay Ending IP
Subnet Mask
Enter DHCP Relay IP Subnet mask

IGR-20 Series User’s Manual
ORing Industrial Networking Corp. 15
List of DHCP Range
for relay
List DHCP Relay IP range
Choose a Client to
Edit
The list shows the MAC addresses and IP addresses that are
already assigned by IGR-20. Choose one from the list and click
Copy to button for editing.
MAC Address
The MAC addresses of the computer.
IP Address
The IP address to be related to the MAC address.
Static DHCP Client
List
The list shows the MAC address and IP address one-to-one
relationship.
DDNS
Dynamic Domain Name System is a method of keeping a domain name linked to a
changing IP address.
DDNS Screen
For example, Choose DDNS Service: www.dyndns.org and configure the following
instructions:
The following table describes the labels in this screen.
Label
Description
User Name
Enter the user name for your DDNS account.
Password
Enter the password for your DDNS account.
Domain
Enter the domain names provided by your dynamic DNS service
provider.
Date&Time
In this page, you can set the date & time of the device. The correct date & time will
be helpful for logging of system events. A NTP (Network Time Protocol) client can be
used to synchronize date & time with NTP server through internet.

IGR-20 Series User’s Manual
ORing Industrial Networking Corp. 16
Date & Time Screen
The following table describes the labels in this screen.
Label
Description
Local Date
Set local date manually.
Local Time
Set local time manually.
Time Zone
Select the time zone manually
Get Current Date &
Time from Browser
Click this button; you can set the time from your browser.
NTP
Enable or disable NTPfunction to synchronize time from the NTP
server.
NTP Server 1
The primary NTP Server.
NTP Server 2
The secondary NTP Server.
Synchronize
This is the scheduled time when the NTP synchronization
performed.