ORiNG TAP-620-M12 User manual

T
TA AP P- -6 62 20 0- -M M1 12 2
E
EN N5 50 01 15 55 5 I IE EE EE E 8 80 02 2. .1 11 1 a a/ /b b/ /g g/ /n n A Ac cc ce es ss s P Po oi in nt t
U
Us se er r’ ’s s M Ma an nu ua al l
V
Ve er rs si io on n 1 1. .0 0
J
Ju ul ly y, , 2 20 01 12 2
w
ww ww w. .o or ri in ng g- -n ne et tw wo or rk ki in ng g. .c co om m

COPYRIGHT NOTICE
Copyright © 2011 ORing Industrial Networking Corp.
All rights reserved.
No part of this publication may be reproduced in any form without the prior written consent of
ORing Industrial Networking Corp.
TRADEMARKS
is a registered trademark of ORing Industrial Networking Corp.
All other trademarks belong to their respective owners.
REGULATORY COMPLIANCE STATEMENT
Product(s) associated with this publication complies/comply with all applicable regulations.
Please refer to the Technical Specifications section for more details.
WARRANTY
ORing warrants that all ORing products are free from defects in material and workmanship
for a specified warranty period from the invoice date (5 years for most products). ORing will
repair or replace products found by ORing to be defective within this warranty period, with
shipment expenses apportioned by ORing and the distributor. This warranty does not cover
product modifications or repairs done by persons other than ORing-approved personnel, and
this warranty does not apply to ORing products that are misused, abused, improperly
installed, or damaged by accidents.
Please refer to the Technical Specifications section for the actual warranty period(s) of the
product(s) associated with this publication.
DISCLAIMER
Information in this publication is intended to be accurate. ORing shall not be responsible for
its use or infringements on third-parties as a result of its use. There may occasionally be
unintentional errors on this publication. ORing reserves the right to revise the contents of this
publication without notice.
CONTACT INFORMATION
ORing Industrial Networking Corp.
3F., No.542-2, Zhongzheng Rd., Xindian Dist., New Taipei City 23148, Taiwan (R.O.C.)
Tel: [phone] // Fax: [phone]
Website: www.oring-networking.com
Technical Support
E-mail: [e-mail]
Sales Contact
E-mail: [e-mail] (Headquarters)
[e-mail] (China)

Table of Content
Getting to Know Your Access Point ............................................................ 1
1.1 About the ORing Access Point......................................................................................1
1.2 Software Features .........................................................................................................1
1.3 Hardware Features........................................................................................................1
Hardware Installation.................................................................................... 2
2.1 Wall Mounting Installation .............................................................................................2
Hardware Overview....................................................................................... 3
3.1 Front Panel.....................................................................................................................3
3.2 Front Panel LEDs ..........................................................................................................5
Cables and Antenna...................................................................................... 5
4.1 Ethernet Cables.............................................................................................................6
4.2 100Base-T(X)/10Base-T Pin Assignments..................................................................6
4.3 Wireless Antenna...........................................................................................................7
Management Interface.................................................................................. 8
5.1 Explore TAP-620-M12...................................................................................................8
5.1.1 Open-Vision_Commander............................................................................................8
5.2 UPnP Equipment ...........................................................................................................9
5.3 Configuration by Web Browser...................................................................................10
5.4 About Web-Based Management.................................................................................10
5.5 Main Interface ..............................................................................................................11
5.5.1 Basic Setting..............................................................................................................12
Setting Operation Mode ......................................................................................................12
Setting WDS (Bridge Mode) ...............................................................................................13
Setting Wireless..................................................................................................................16
Client..................................................................................................................................21
LAN Setting .......................................................................................................................22
Setting DHCP Server ..........................................................................................................23
5.5.2 Advanced Setting.......................................................................................................24
Wireless..............................................................................................................................24
X-Roaming.........................................................................................................................26

MAC Filter.........................................................................................................................26
System Event......................................................................................................................27
Email Settings.....................................................................................................................28
SNMP Settings....................................................................................................................29
Syslog Server Settings.........................................................................................................30
5.5.3 System Tools .............................................................................................................30
Administrator......................................................................................................................30
Date & Time.......................................................................................................................32
Configuration......................................................................................................................33
Firmware Upgrade..............................................................................................................33
Miscellaneous.....................................................................................................................34
5.5.4 System Status.............................................................................................................35
System Info ........................................................................................................................35
System Log.........................................................................................................................36
Traffic Statistics..................................................................................................................36
5.5.5 Online Help ...............................................................................................................37
Technical Specifications ............................................................................ 38
Compliance.................................................................................................. 40

TAP-620-M12 User’s Manual
1ORing Industrial Networking Corp.
Getting to Know Your Access Point
1.1 About the ORing Access Point
TAP-620-M12 is reliable IEEE802.11a/b/g/n WLAN
with 2 ports LAN Access Point. It can be configured to
operate in AP/Client/Bridge mode. You can configure
TAP-620-M12 by Window Utility or WEB interfaces via LAN
port or WLAN interface. TAP-620-M12 provides dual
Ethernet ports in switch mode, so you can use Daisy Chain
to reduce the usage of Ethernet switch ports. Therefore,
TAP-620-M12 is one of the best communication solutions
for wireless application.
1.2 Software Features
High Speed Air Connectivity: WLAN interface support up to 300Mbps link speed
connection
Highly Security Capability: WEP/WPA/WPA2/Radius/TKIP supported
Support AP/Client/Bridge/AP-Client Mode
Switch Mode Supported: Daisy Chain support to reduce usage of switch ports
Secured Management by HTTPS
Event Warning by Syslog, Email, SNMP Trap, Relay and Beeper
1.3 Hardware Features
Redundant Power Inputs: Dual 12~48 VDC on M23 connector
10/100Base-T(X) Ethernet port
Casing: IP-40
Dimensions(W x D x H) : 125mm(W) x 65mm(D) x 196mm(H)
Operating Temperature: -20 to 70oC
Storage Temperature: -40 to 85oC
Operating Humidity: 5% to 95%, non-condensing

TAP-620-M12 User’s Manual
ORing Industrial Networking Corp. 2
Hardware Installation
2.1 Wall Mounting Installation
Each AP has another installation method to fix the AP. The following steps show how
to mount the AP on the wall:
Step 1: Use screws that can be found in the package to combine the wall mount
TAP-620-M12.
The screws specification shows in the following two pictures. In order to prevent the
AP from any damage, the screws should not larger than the size that used in
TAP-620-M12.
Step 2: Mount the combined AP on the wall.

TAP-620-M12 User’s Manual
3ORing Industrial Networking Corp.
Hardware Overview
3.1 Front Panel
The following table describes the labels that stick on the TAP-620-M12.
Port Description
10/100 Base-T(X) fast
Ethernet ports on
M12 connector
(D-coding)
2 10/100Base-T(X) fast Ethernet ports support auto-negotiation.
Default Setting :
Speed: auto
Relay Output on M12
(A-coding) connector
Relay output to carry capacity of 3A at 24VDC
Redundant power
inputs on M23
connector
Dual Power Inputs. 12~48 VDC on M23 connector

TAP-620-M12 User’s Manual
ORing Industrial Networking Corp. 4
TAP-620-M12
1. 2.4/5 GHz antenna with typical 3.0 dBi antenna for 5GHz and 2 dBi for 2.4GHz.
2. LED for PWR1 and system status. When the PWR1 links, the green LED will be light
on.
3. LED for PWR2 and system status. When the PWR2 links, the green LED will be light
on.
4. LED for Ethernet port1 status.
5. LED for Ethernet port2 status.
6. LED for WLAN link status.
7. LED for Fault Relay. When the fault occurs, the red LED will be light on.
8. Power Input port on M23 connector
9. Ethernet port1 on M12(D-coding) connector

TAP-620-M12 User’s Manual
5ORing Industrial Networking Corp.
10. Ethernet port2 on M12(D-coding) connector
11. Relay output on M12(A-coding) connector
3.2 Front Panel LEDs
LED Color Status Description
PWR1 Green/Red
Green On DC power 1 activated.
Green blinking Device been located
Red blinking
Indicates an IP conflict, or
DHCP or BOOTP server did
not respond properly
PWR2 Green/Red
Green On
DC power 2 activated.
Green blinking Device been located
Red blinking
Indicates an IP conflict, or
DHCP or BOOTP server did
not respond properly
ETH1
Amber On Port link up at 10Mbps.
Blinking Data transmitted.
Green On Port link up at 100Mbps.
Blinking Data transmitted.
ETH2
Amber On Port link up at 10Mbps.
Blinking Data transmitted.
Green On Port link up at 100Mbps.
Blinking Data transmitted.
WLAN
Green On WLAN1 activated.
Blinking WLAN1 Data transmitted.
Red On WLAN2 activated.
Blinking WLAN2 Data transmitted.
Fault Red On Fault relay. Power failure or
Port down/fail.
Cables and Antenna

TAP-620-M12 User’s Manual
ORing Industrial Networking Corp. 6
4.1 Ethernet Cables
The TAP-620-M12 WLAN AP has two 10/100Base-T(X) Ethernet ports. According to
the link type, theAP use CAT 3, 4, 5,5e UTP cables to connect to any other network device
(PCs, servers, switches, routers, or hubs). Please refer to the following table for cable
specifications.
Cable Types and Specifications
Cable Type Max. Length Connector
10Base-T Cat. 3, 4, 5 100-ohm UTP 100 m (328 ft) M12(D-codng)
100Base-T(X) Cat. 5 100-ohm UTP UTP 100 m (328 ft) M12(D-coding)
4.2 100Base-T(X)/10Base-T Pin Assignments
With 100Base-T(X)/10Base-T cable, pins 1 and 2 are used for transmitting data, and
pins 3 and 6 are used for receiving data.
M12(4-pin, D-coding) Pin Assignments
Pin Number Assignment
1 RD+
2 TD+
3 RD-
4 TD-
The TAP-620-M12 supports auto MDI/MDI-X operation. You can use a straight-through
cable to connect PC and AP. The following table below shows the 10Base-T/
100Base-T(X) MDI and MDI-X port pin outs.
MDI/MDI-X pins assignment
Pin Number MDI port MDI-X port
1 RD+(receive) TD+(transmit)
2 TD+(transmit) RD+(receive)
3 RD-(receive) TD-(transmit)
4 TD-(transmit) RD-(receive)
Note: “+” and “-” signs represent the polarity of the wires that make up each wire pair.

TAP-620-M12 User’s Manual
7ORing Industrial Networking Corp.
4.3 Wireless Antenna
2.4GHz/5GHz antenna is used for TAP-620-M12 and connected with a reversed SMA
connector. External RF cable and antenna also can be applied with this connector.

TAP-620-M12 User’s Manual
ORing Industrial Networking Corp. 8
Management Interface
5.1 Explore TAP-620-M12
5.1.1 Open-Vision_Commander
TAP-620-M12 can also be configure through Oring’s window utility Open-Vision
Step 1: Open the commander and click “Discover”, the AP devices will show on the list.
Step 2: Choose your access point, and it will show the AP function tree. Simultaneity,
you can login and then set the AP.
User interface of commander

TAP-620-M12 User’s Manual
9ORing Industrial Networking Corp.
5.2 UPnP Equipment
Step 1: To check whether the UPnP UI of the computer is connected to the TAP-620-M12,
go to Control Panel > Add or Remove Programs > Windows Components Wizard >
Networking Servers > UPnP User Interface and pitch on the UPnP User Interface.
UPnP configuration page
Step 2: At the right-below corner of the computer, you will find a sign of the UPnP
equipment.

TAP-620-M12 User’s Manual
ORing Industrial Networking Corp. 10
Step 3: Click the sign of the UPnP equipment, then you will find the UPnP equipment in the
network neighborhood.
Step 4: Right click the UPnP equipment to choose “Properties”, it will show as the following
pictures:
Step 5: Right click the UPnP equipment or double click the UPnP equipment to transfer; it
will go to the web page.
5.3 Configuration by Web Browser
This section introduces the configuration by Web browser.
5.4 About Web-Based Management
An embedded HTML web site resides in flash memory in the system. It contains
advanced management features and allows you to manage the AP from anywhere on the
network through a standard web browser such as Microsoft Internet Explorer.
The Web-Based Management function supports Internet Explorer 5.0 or later. It is based
on Java Applets with an aim to reduce network bandwidth consumption, enhance access
speed and present an easy viewing screen.
Note: By default, IE5.0 or later version does not allow Java Applets to open sockets. You need to explicitly modify
the browser setting in order to enable Java Applets to use network ports.

TAP-620-M12 User’s Manual
11 ORing Industrial Networking Corp.
Through the front section’s information, you will see as follows, enter your user name
(admin) and your password (admin), and then click OK to continue.
Login screen
For security reasons, we strongly suggest you change the password. Click on System
Tools > Administrator and modify the password.
5.5 Main Interface
The Home screen will appear. Please click “Run Wizard” to go to the Home > Setup
Wizard page to quick install the AP.
Main interface

TAP-620-M12 User’s Manual
ORing Industrial Networking Corp. 12
5.5.1 Basic Setting
Setting Operation Mode
Operation mode interface
The following table describes the labels in this screen.
Label Description
AP This mode provides Access Point services for other wireless
clients.
AP-Client The AP-Client function provides a 1-to-N MAC address mapping
mechanism such that multiple stations behind the AP can
transparently connect to the other AP even they didn’t support
WDS.
Client In this mode the AP functions as a wireless client to connect to
other AP, thus provides transparent connection between Ethernet
& wireless port. This mode provides no Access Point services but
with 802.1X supported.
Bridge This mode provides Static LAN-to-LAN Bridging functionality.
The static LAN-to-LAN bridging function is supported through
Wireless Distribution System (WDS).
In each mode, the TAP-620-M12 forwards packet between its Ethernet interface and
wireless interface for wired hosts on the Ethernet side, and wireless hosts on the wireless
side.

TAP-620-M12 User’s Manual
13 ORing Industrial Networking Corp.
Setting WDS (Bridge Mode)
WDS setting interface
This type of wireless link is established between two IEEE 802.11 access points.
Wireless packets transmitted along the WDS link comply with the IEEE 802.11 WDS
(Wireless Distribution System) format at the link layer.
Point-to-Point WDS Link
The following table describes the labels in this screen.
Label Description
WDS Mode This mode provides Static LAN-to-LAN Bridging functionality.
The static LAN-to-LAN bridging function is supported through
Wireless Distribution System (WDS).
Peer MAC Address Set the Mac address of other access point(s). Simultaneity,
choose on “Enable”.
First of all, if APs link with WDS mode, it should obey the following rules:
1. LAN IP Address should set different IP in the same network.

TAP-620-M12 User’s Manual
ORing Industrial Networking Corp. 14
2. All AP’s DHCP Server should set shutdown.
3. WDS should set Enable.
4. Each AP should have the same setting except ‘Peer Mac Address’ set to the other’s
Mac address
5. At wireless web setting Security and Channel should be the same,
6. AP’s distance should be limited within a certainty area.
WDS –Bridge Mode
The peer WDS APs are according to the MAC address listed in "Peer Mac Address"
fields.
The working principle of Bridge Mode as follows:
In the figure, the AP behaves as a standard bridge that forwards traffic between WDS links
(links that connect to other AP/wireless bridges) and an Ethernet port. As a standard bridge,
the AP learns MAC addresses of up to 64 wireless or 128 total wired and wireless network
devices, which are connected to their respective Ethernet ports to limit the amount of data to
be forwarded. Only data destined for stations which are known to reside on the peer Ethernet
link, multicast data or data with unknown destinations need to be forwarded to the peer AP via
the WDS link.

TAP-620-M12 User’s Manual
15 ORing Industrial Networking Corp.
WDS –Repeater Mode
The peer WDS APs are according to the MAC address listed in "Peer Mac Address"
fields.
The working principle of Repeater Mode as follows:
In the figure, Repeater is used to extend the range of the wireless infrastructure by
forwarding traffic between associated wireless stations and another repeater or AP
connected to the wired LAN.
LAN
WDS
LAN
WDS