ORiNG IGAP-W99110GP+ User manual

IGAP-W99110GP+
Industrial Dual Wi-Fi 6 Wireless Access Point
User Manual
Version 1.0
Aug, 2021
https://oringnet.com/

IGAP-W99110GP+ User Manual
ORing Industrial Networking Corp.
1
COPYRIGHT NOTICE
Copyright © 2021 ORing Industrial Networking Corp.
All rights reserved.
No part of this publication may be reproduced in any form without the prior written consent of
ORing Industrial Networking Corp.
TRADEMARKS
is a registered trademark of ORing Industrial Networking Corp.
All other trademarks belong to their respective owners.
REGULATORY COMPLIANCE STATEMENT
Product(s) associated with this publication complies/comply with all applicable regulations.
Please refer to the Technical Specifications section for more details.
WARRANTY
ORing warrants that all ORing products are free from defects in material and workmanship for
a specified warranty period from the invoice date (5 years for most products). ORing will repair
or replace products found by ORing to be defective within this warranty period, with shipment
expenses apportioned by ORing and the distributor. This warranty does not cover product
modifications or repairs done by persons other than ORing-approved personnel, and this
warranty does not apply to ORing products that are misused, abused, improperly installed, or
damaged by accidents.
Please refer to the Technical Specifications section for the actual warranty period(s) of the
product(s) associated with this publication.
DISCLAIMER
Information in this publication is intended to be accurate. ORing shall not be responsible for its
use or infringements on third-parties as a result of its use. There may occasionally be
unintentional errors on this publication. ORing reserves the right to revise the contents of this
publication without notice.
CONTACT INFORMATION
ORing Industrial Networking Corp.
3F., NO.542-2, JhongJheng Rd., Sindian District, New Taipei City 231, Taiwan, R.O.C.
Tel: + 886 2 2218 1066 // Fax: + 886 2 2218 1014
Website: https://oringnet.com/
Technical Support: s[email protected]
Sales Contact: sa[email protected] (Headquarter)
[e-mail] (China)

IGAP-W99110GP+ User Manual
ORing Industrial Networking Corp.
2
Table of Content
Getting Started ...............................................................................................4
1.1 About the IGAP-W99110GP+..................................................................................... 4
1.2 Software Features ...................................................................................................... 4
1.3 Hardware Specifications ............................................................................................ 5
Hardware Overview........................................................................................6
2.1 Product Appearance................................................................................................... 6
2.1.1 Ports and connectors ........................................................................................ 6
2.1.2 LED.................................................................................................................... 6
2.2 Dimension .................................................................................................................. 7
Hardware Installation.....................................................................................8
3.1 Grounding and Lightning Protection........................................................................... 8
3.2 Preparing the Installation Site .................................................................................... 9
3.2.1 Temperature and Humidity............................................................................. 9
3.2.2 Outdoor Installation......................................................................................... 9
3.2.3 Waterproof ...................................................................................................... 9
3.2.4 EMI................................................................................................................ 10
3.2.5 Fiber Connection .......................................................................................... 10
3.2.6 Console Connection ..................................................................................... 10
3.2.7 Checking before Installation ......................................................................... 10
3.3 Installing the Access Point ........................................................................................11
3.3.1 Installation Flowchart .....................................................................................11
3.3.2 Before You Begin ...........................................................................................11
3.3.3 Precautions ................................................................................................... 12
3.3.4 Installing the AP ............................................................................................ 12
3.3.5 Cables and Pin Assignment.......................................................................... 14
3.3.6 Connecting Cables ....................................................................................... 15
Web-based Configuration ...........................................................................19
4.1 Overview .................................................................................................................. 19
4.2 Config Wizard........................................................................................................... 21
4.3 Monitoring................................................................................................................. 23
4.3.1 Dashboard .................................................................................................... 23

IGAP-W99110GP+ User Manual
ORing Industrial Networking Corp.
3
4.3.2 User Info ....................................................................................................... 23
4.3.3 DHCP............................................................................................................ 24
4.4 Configuration ............................................................................................................ 25
4.4.1 Wireless ........................................................................................................ 25
4.4.2 AP ................................................................................................................. 27
4.4.3 Network......................................................................................................... 31
4.4.4 Security ......................................................................................................... 46
4.4.5 Authentication ............................................................................................... 60
4.4.6 Advanced ...................................................................................................... 61
4.4.7 Rapid............................................................................................................. 62
4.5 Maintenance............................................................................................................. 63
4.5.1 Settings ......................................................................................................... 63
4.5.2 System .......................................................................................................... 65
Appendix ......................................................................................................68
5.1 Product Specification.............................................................................................. 68
5.2 Antenna Patterns.................................................................................................... 69

IGAP-W99110GP+ User Manual
ORing Industrial Networking Corp.
4
Getting Started
1.1 About the IGAP-W99110GP+
The IGAP-W99110GP+ is a high-performance Wi-Fi 6 (IEEE802.11ax) industrial outdoor access point.
The IGAP-W99110GP+ provide concurrent dual-band dual-radio with up to 2.4Gbps access rate, it offers
4 spatial streams. The interface includes one SFP port and one Gigabit Ethernet port with PoE/ local
power supply. Taking the wireless network security, RF control, mobile access, QoS and other important
factors into account. By the technologies implemented in IEEE802.11ax, such as OFDMA, BSS Color and
MU-MIMO, it can reduce the network latency, spatial reuse and improve the network efficiency.
IGAP-W99110GP+ adopts the IP68 protection design for the enclosure, which is suitable for application
in indoor and outdoor environments. It can withstand extreme weather and other environmental conditions.
Equipped with built-in directional antenna, IGAP-W99110GP+ can achieve the Wi-Fi coverage in vast
majority of the scenarios and greatly reduce the difficulty of installation and maintenance. Multi-hop and
point-to-multipoint bridge features are supported to further enhance the deployment flexibility.
1.2 Software Features
Highly Security Capability: WEP/ WPA/ WPA-PSK(TKIP,AES)/ WPA2/ WPA2 PSK(TKIP,AES)/
802.1X Authentication supported
Support wireless load balance
Max 1024 client connections
Supports a wide variety of QoS policies
ARP Spoofing Protection
Support IPv4/IPv6 address
Support AP/Client Mode
SSID capacity up to 32
Wireless connecting status monitoring
Secured Management by Telnet, SSH, TFTP, HTTP
Event Warning by Syslog

IGAP-W99110GP+ User Manual
ORing Industrial Networking Corp.
5
1.3 Hardware Specifications
High Speed Air Connectivity: WLAN interface support up to 2400Mbps link speed
Dual-Band Dual-Radio IEEE802.11ax with 4 spatial streams
Build-in 9dBi Directional Antenna
1x 10/100/1000Base-T(X) port
1x Gigabit SFP socket
1x Console port
Surge Protection +/-9kV (Common mode)
IP68 enclosure for outdoor applications
Operating temperature -40 to 65οC
Dimension 251(W) x 168(D) × 64(H) mm
Wall/Pole-mount installation

IGAP-W99110GP+ User Manual
ORing Industrial Networking Corp.
6
Hardware Overview
2.1 Product Appearance
2.1.1 Ports and connectors
Note:
1. Console port and reset button
2. Port for 48VDC power supply
3. 10/100/1000 Base-T Ethernet/PoE PD port
4. SFP port
2.1.2 LED
The following table describes the function of each LED indicator.
LED
State
Meaning
System status
Blinking green
The system is booting.
Solid green
Initialization in progress or proper operation.
Blinking red
The uplink port is disconnected.
WDS RSSI (3 LEDs
in total; available
when bridging is
enabled)
1 solid on
< -70dBm
2 solid on
-70 to -50dBm
3 solid on
> -50dBm

IGAP-W99110GP+ User Manual
ORing Industrial Networking Corp.
7
2.2 Dimension
IGAP-W99110GP+ dimension: 251(W) x 168(D) × 64(H) mm (Excluding the bracket)

IGAP-W99110GP+ User Manual
ORing Industrial Networking Corp.
8
Hardware Installation
To prevent device damage and physical injury, please read carefully the safety recommendations
described in this chapter.
Recommendations do not cover all possible hazardous situations.
3.1 Grounding and Lightning Protection
Ensure that both the power-receiving end and the power-supplying end are well-grounded.
Keep the grounding connection within 30 m, and use a 40mm x 4mm or 50mm x 5mm ground bar of
hot-dip zinc-coated flat steel sheet.
When the connection cable between the main grounding conductor and local equipotential earthing
terminal board (LEB) on each floor is shorter than 2 meters, use a stranded copper wire with a
sectional area not less than 1.318 mm2 (16 AWG) for the connection cable.
Use a shielded network cable if possible, ensure that devices connected to both ends of the shielded
network cable are reliably grounded, and make sure that the sheath of the shielded network cable is
also grounded if possible. If no shielded network cable is available, wire the network cable through
a steel pipe and bury the steel pipe for lead-in, and properly ground both ends of the steel pipe.
No additional lightning protector is required as a high-profile lightning protector is built in the IGAP-
W99110GP+, and the power port support 6kV lightning protection. If a lightning protector of a higher
profile is available, configure the lightning protector optionally. Before the configuration, connect the
lightning protector to the ground cable.
Use a power cable with the PE end to ground the power supply (AC). Ensure that the PE end is
properly grounded, with a ground resistance less than 5 ohms. Do not use a two-wire power cable
with only the live (L) wire and naught (N) wire. Do not connect the N wire to the protection ground
cable of other communication devices, and ensure that the L wire and N wire are properly connected.
Ensure that the ground resistance is less than 5 ohms. In areas with high soil resistivity, reduce the
soil resistivity via measures such as spreading resistivity reduction mixture around the grounding
conductor.

IGAP-W99110GP+ User Manual
ORing Industrial Networking Corp.
9
3.2 Preparing the Installation Site
Do not expose the AP to high temperature, dust, or harmful gases.
Do not install the AP in an area prone to fire or explosions.
Keep the AP away from EMI sources such as large radar stations, radio stations, and substations.
Do not subject the AP to unstable voltage, vibration, and noises.
Keep the AP at least 500 meters away from the ocean and do not face it towards the sea breeze.
The installation site should be protected from water and flooding, seepage, dripping, or condensation.
The installation site should be selected according to network planning, communications equipment
features and considerations such as climate, hydrology, geology, earthquake, electric power, and
transportation.
3.2.1 Temperature and Humidity
The following table shows required temperature and humidity for IGAP-W99110GP+
Operating Temperature
-40°C to 65°C (-40°F to 149°F)
Operating Humidity
0% to 100% (non-condensing)
3.2.2 Outdoor Installation
The AP can be mounted on a wall or pole.
3.2.3 Waterproof
Use a seal plug to seal the unused ports.
Use a watertight adapter to connect cables to the AP. For details, see Chapter “Installing the Access
Point”.

IGAP-W99110GP+ User Manual
ORing Industrial Networking Corp.
10
3.2.4 EMI
All interference sources (from outside or inside of the device or application system) affect the device by
capacitive coupling, inductive coupling, or electromagnetic waves.
Electromagnetic interference (EMI) occurs due to electromagnetic radiation or conduction, depending on
the transmission path.
Radiation interference occurs when energy (usually radio frequency energy) is emitted from a device
and propagated through space to disrupt other devices. The interference source can be part of disrupted
system or a fully electrically isolated unit. Conduction interference occurs when interference is
transferred from one unit to another through cables, which are usually electromagnetic wires or signal
cables connected between the source and the device(s) experiencing interference. Conduction
interference often affects the power supply of the device. It is eliminated by using filters. Radiation
interference can influence the path of any signal from the device and is difficult to shield.
Take effective measures against interference from the power grid.
Keep the AP far away from the grounding or lightning protection devices for power equipment.
Keep the AP away from high-power radio stations, radar stations, and high-frequency high-current
devices.
Take electrostatic shielding measures.
3.2.5 Fiber Connection
Before connecting fiber cables, make sure the model of the optical transceiver and fiber type match the
optical port. The transmit port on the local device should be connected to the receive port on the peer
device and vice versa.
3.2.6 Console Connection
Please attach RS-232 console cable to your PC COM port, and connect the other end to the Console
port of IGAP-W99110GP+, open Terminal tool and set up serial settings to 9600, N,8,1. (Baud Rate:
9600 / Parity: None / Data Bit: 8 / Stop Bit: 1) Then you can access CLI interface. The default
username/password is admin/admin.
3.2.7 Checking before Installation
Please check your materials carefully against the package contents. If there are any errors, please
contact your distributor or ORing sales representative.

IGAP-W99110GP+ User Manual
ORing Industrial Networking Corp.
11
3.3 Installing the Access Point
3.3.1 Installation Flowchart
3.3.2 Before You Begin
Before you install the AP, verify that all the parts in the package contents are there and make sure that:
The installation site meets temperature and humidity requirements.
The installation site is equipped with a proper power supply.
Network cables are in place.

IGAP-W99110GP+ User Manual
ORing Industrial Networking Corp.
12
3.3.3 Precautions
IGAP-W99110GP+ can be mounted on a wall and a pole (diameter: 50mm to 140mm, thickness: ≥
2.5mm). Otherwise, the AP could fall down and cause injuries. The installation site can vary due to on-
the-spot surveys conducted by technical personnel.
Please make full preparations as described in Chapter 2 and observe the following precautions before
installing the AP.
Before connecting the power supply, make sure the external power supply matches the power
module inside the AP.
Before connecting the power cord, make sure the power switch is in the OFF position.
When connecting a wire to a binding post, make sure their colors are the same.
Make sure the power supply is properly connected.
3.3.4 Installing the AP
1. Use four M5 screws to secure the AP to the mounting plate.
Figure: Securing the AP with M5 Screws
2. Install the mounting bracket to a pole or wall.
Pole mount
Attach the bracket to a pole with two hose clamp and fasten the clamp with screws and nuts.

IGAP-W99110GP+ User Manual
ORing Industrial Networking Corp.
13
Figure: Mounting the Bracket on a Pole
Wall mount
Use four M8 x 60 screws to implement the wall mount. (The screws, made of SUS304 stainless steel,
are customer-supplied.)
a. Attach the bracket to the wall and mark the screw hole locations.
b. Align the screw holes on the bracket and those on the wall, and tighten the M8 x 40 screws to
mount the bracket.
Figure: Mounting the Bracket on Wall

IGAP-W99110GP+ User Manual
ORing Industrial Networking Corp.
14
3. Use four M6 screws to join the mounting plate and the bracket. Adjust the angle of the device before
fastening the screws.
Figure: Complete the Installation
3.3.5 Cables and Pin Assignment
The 1000BASE-T/100BASE-TX/10BASE-T is a 10/100/1000 Mbps auto-negotiation port that supports
auto MDI/MDIX. Compliant with IEEE 802.3ab, 1000BASE-T requires Category 5e 100-ohm UTP or
STP (STP is recommended) with a maximum distance of 100 meters (328 feet). 1000BASE-T requires
all four pairs of wires be connected for data transmission.
Figure: 1000BASE-T Connection
10BASE-T uses Category 3, 4, 5 100-ohm UTP/STP and 1000BASE-T uses Category 5 100-ohm
UTP/STP for connections. Both support a maximum length of 100 meters.

IGAP-W99110GP+ User Manual
ORing Industrial Networking Corp.
15
Table: 100BASE-TX/10BASE-T Pin Assignments
The figure below shows the wiring of straight-through and crossover cables for 100BASE-TX/10BASE-T.
Fiber Connection
You can choose to use single-mode or multi-mode fiber according to the transceiver module types.
Figure below shows connection of fiber cables.
3.3.6 Connecting Cables
Connecting the grounding cable
The grounding cable is made on site. Connect the supplied grounding wire (yellow-green) to the AP
grounding hole on one end and ground the wire on the other end through OT terminals. To avoid waste,
adjust the cable length for actual demands.

IGAP-W99110GP+ User Manual
ORing Industrial Networking Corp.
16
Figure: Grounding the AP
Connecting the network cable
Waterproofing material is customer-supplied.
1. Trim the network cable according to the distance between the AP and the power supply. And put the
trimmed cable through the bracket.
2. Thread the cable through liquid-tight adapter and add a plug to the end. See figure below.
Figure: Threading the Network Cable
3. Wrap the cable between B and C upwards with two or three layers of liquid-tight material. See figure
below.
Figure: Wrapping Liquid-tight Material around Cable

IGAP-W99110GP+ User Manual
ORing Industrial Networking Corp.
17
4. Insert the plug into the ETH/PoE port and tighten B, C and D in order.
Make sure the plug is correctly inserted. The plug can be damaged if the liquid-tight adapter is
improperly tightened.
Before removing the network cable, dismantle the liquid-tight adapter first and then the plug.
Connecting the optical fiber
Waterproofing material is customer-supplied.
1. Choose an LC-LC optical fiber with the diameter of 2.7±0.2mm.
2. Thread the fiber through the liquid-tight adapter in the order as shown in figure below.
Figure: Threading the Fiber
3. Insert the plug of the fiber into the SFP port.
4. Tighten A.
5. Combine B and C and put the combination into A.
6. Tighten D before applying waterproof glue to its joint with A.
Before removing the optical fiber, dismantle the liquid-tight adapter first and then the plug.
If the diameter of LC-LC fiber is not 2.7±0.2mm, waterproofness of the adapter cannot be guaranteed.
Connecting the DC Power Cord (Optional)
Waterproofing material is customer-supplied.
Please make sure the port for DC power supply face to the ground.

IGAP-W99110GP+ User Manual
ORing Industrial Networking Corp.
18
Thread the DC power cord through the liquid-tight adapter in the order as shown in Figure below. Use
waterproof duct tape and waterproof plaster to fill in the space between the power cord and the adapter.
Figure: Threading the DC Power Cord

IGAP-W99110GP+ User Manual
ORing Industrial Networking Corp.
19
Web-based Configuration
4.1 Overview
The AP can be controlled via a built-in web server which supports Internet Explorer (Internet Explorer 7.0
or above versions) and other Web browsers such as Chrome, Firefox and some IE kernel-based browsers.
Therefore, you can manage and configure the switch easily and remotely. You can also upgrade firmware
via a web browser. The Web management function not only reduces network bandwidth consumption, but
also enhances access speed and provides a user-friendly viewing screen.
The Web management system integrates configuration commands and sends them to the device through
AJAX requests. Web service is enabled on the device to process HTTP requests to return requested data.
Note
It is recommended that the resolution be set to 1024 x 768, 1280 x 1024, or 1440 x 960.
Exceptions such as font alignment error and format error may occur when other resolutions
are selected.
The following table lists the Web management system default configuration.
Feature
Default Settings
Web service
Enabled
Management IP
192.168.110.1
Default Username/Password
admin/admin
The default password is not saved in show running-config.