ORiNG IAP-620 Series User manual

IAP-620 Series User’s Manual
1 ORingIndustrialNetworkingCorp.
I
IA AP P- -6 62 20 0 S Se er ri ie es s
I
IE EE EE E 8 80 02 2. .1 11 1 a a/ /b b/ /g g/ /n n A Ac cc ce es ss s P Po oi in nt t
U
Us se er r’ ’s s M Ma an nu ua al l
V
Ve er rs si io on n 1 1. .0 0
J
Ju ul ly y, , 2 20 01 12 2
w
ww ww w. .o or ri in ng g- -n ne et tw wo or rk ki in ng g. .c co om m

IAP-620 Series User’s Manual
ORingIndustrialNetworkingCorp. 2
COPYRIGHT NOTICE
Copyright © 2011 ORing Industrial Networking Corp.
All rights reserved.
No part of this publication may be reproduced in any form without the prior written consent of
ORing Industrial Networking Corp.
TRADEMARKS
is a registered trademark of ORing Industrial Networking Corp.
All other trademarks belong to their respective owners.
REGULATORY COMPLIANCE STATEMENT
Product(s) associated with this publication complies/comply with all applicable regulations.
Please refer to the Technical Specifications section for more details.
WARRANTY
ORing warrants that all ORing products are free from defects in material and workmanship
for a specified warranty period from the invoice date (5 years for most products). ORing will
repair or replace products found by ORing to be defective within this warranty period, with
shipment expenses apportioned by ORing and the distributor. This warranty does not cover
product modifications or repairs done by persons other than ORing-approved personnel, and
this warranty does not apply to ORing products that are misused, abused, improperly
installed, or damaged by accidents.
Please refer to the Technical Specifications section for the actual warranty period(s) of the
product(s) associated with this publication.
DISCLAIMER
Information in this publication is intended to be accurate. ORing shall not be responsible for
its use or infringements on third-parties as a result of its use. There may occasionally be
unintentional errors on this publication. ORing reserves the right to revise the contents of this
publication without notice.
CONTACT INFORMATION
ORing Industrial Networking Corp.
3F., No.542-2, Zhongzheng Rd., Xindian Dist., New Taipei City 23148, Taiwan (R.O.C.)
Tel: [phone] // Fax: [phone]
Website: www.oring-networking.com
Technical Support
E-mail: [e-mail]
Sales Contact
E-mail: [e-mail] (Headquarters)
[e-mail] (China)

IAP-620 Series User’s Manual
3 ORingIndustrialNetworkingCorp.
Table of Content
Getting to Know Your Access Point............................................................ 5
1.1About the ORing Access Point..........................................................................................5
1.2Software Features ..............................................................................................................5
1.3Hardware Features.............................................................................................................5
Hardware Installation.................................................................................... 6
2.1Installation AP on DIN-Rail................................................................................................6
2.2Wall Mounting Installation..................................................................................................7
Hardware Overview....................................................................................... 9
3.1Front Panel..........................................................................................................................9
3.2Front Panel LEDs .............................................................................................................11
3.3Bottom Panel.....................................................................................................................12
3.4Rear Panel.........................................................................................................................12
Cables and Antenna.....................................................................................13
4.1Ethernet Cables................................................................................................................13
4.2100Base-T(X)/10Base-T Pin Assignments ...................................................................13
4.3Wireless Antenna..............................................................................................................14
Management Interface.................................................................................15
5.1Explore IAP-620/IAP-620+..............................................................................................15
5.1.1Open-Vision_Commander..............................................................................................15
5.2UPnP Equipment ..............................................................................................................16
5.3Configuration by Web Browser.......................................................................................17
5.4About Web-Based Management ....................................................................................17
5.5Main Interface....................................................................................................................18
5.5.1Basic Setting...................................................................................................................19
Setting Operation Mode...........................................................................................................19
Setting WDS (Bridge Mode)....................................................................................................20
Setting Wireless........................................................................................................................23
Client........................................................................................................................................28
LAN Setting.............................................................................................................................29
Setting DHCP Server................................................................................................................30

IAP-620 Series User’s Manual
ORingIndustrialNetworkingCorp. 4
5.5.2Advanced Setting............................................................................................................31
Wireless....................................................................................................................................31
X-Roaming...............................................................................................................................33
MAC Filter...............................................................................................................................33
System Event............................................................................................................................34
Email Settings ..........................................................................................................................35
SNMP Settings.........................................................................................................................36
Syslog Server Settings..............................................................................................................37
5.5.3System Tools...................................................................................................................38
Administrator ...........................................................................................................................38
Date & Time.............................................................................................................................40
Configuration ...........................................................................................................................41
Firmware Upgrade ...................................................................................................................42
Miscellaneous...........................................................................................................................42
5.5.4System Status..................................................................................................................43
System Info ..............................................................................................................................43
System Log ..............................................................................................................................44
Traffic Statistics........................................................................................................................44
5.5.5Online Help.....................................................................................................................45
Technical Specifications .............................................................................46
Compliance...................................................................................................48

IAP-620 Series User’s Manual
5 ORingIndustrialNetworkingCorp.
Getting to Know Your Access Point
1.1 About the ORing Access Point
IAP-620/IAP-620+ is reliable IEEE802.11a/b/g/n WLAN with 2
ports LAN Access Point. It can be configured to operate in
AP/Client/Bridge/AP-Client mode. You can configure
IAP-620/IAP-620+ by Windows Utility or WEB interfaces via LAN port
or WLAN interface. IAP-620/IAP-620+ provides dual Ethernet ports in
switch mode, so you can use Daisy Chain to reduce the usage of
Ethernet switch ports. Therefore, IAP-620/IAP-620+ is one of the
best communication solutions for wireless application.
1.2 Software Features
High Speed Air Connectivity: WLAN interface support up to 300Mbps link speed
connection
Highly Security Capability: WEP/WPA/WPA2/802.1x supported
Support AP/Client/Bridge/AP-Client Mode
Switch Mode Supported: Daisy Chain support to reduce usage of switch ports
Secured Management by HTTPS
Event Warning by Syslog, Email, SNMP Trap, Relay and Beeper
1.3 Hardware Features
Fully Compliant with IEEE802.3af (Power Device at ETH2, IAP-620+ only)
Redundant Power Inputs: Dual 12~48 VDC on terminal block
10/100Base-T(X) Ethernet port
Casing: IP-30
Dimensions(W x D x H) : 52 mm(W)x 106 mm( D )x 144 mm(H)
Operating Temperature: -10 to 60oC
Storage Temperature: -40 to 85oC
Operating Humidity: 5% to 95%, non-condensing

IAP-620 Series User’s Manual
ORingIndustrialNetworkingCorp. 6
Hardware Installation
2.1 Installation AP on DIN-Rail
Each AP has a DIN-Rail kit on rear panel. The DIN-Rail kit helps AP to fix on the
DIN-Rail. It is easy to install the AP on the DIN-Rail:
Step 1: Slant the AP and mount the metal spring to DIN-Rail.
Step 2: Push the AP toward the DIN-Rail until you heard a “click” sound.

IAP-620 Series User’s Manual
7 ORingIndustrialNetworkingCorp.
2.2 Wall Mounting Installation
Each AP has another installation method to fix the AP. A wall mount panel can be
found in the package. The following steps show how to mount theAP on the wall:
Step 1: Remove DIN-Rail kit.
Step 2: Use 6 screws that can be found in the package to combine the wall mount panel.
Just like the picture shows below:

IAP-620 Series User’s Manual
ORingIndustrialNetworkingCorp. 8
The screws specification shows in the following two pictures. In order to prevent the
AP from any damage, the screws should not larger than the size that used in IAP-620 /
620+.
Pozidrive
Step 3: Mount the combined AP on the wall.

IAP-620 Series User’s Manual
9 ORingIndustrialNetworkingCorp.
Hardware Overview
3.1 Front Panel
The following table describes the labels that stick on the IAP-620/IAP-620+.
Port Description
10/100 RJ-45 fast
Ethernet ports
2 10/100Base-T(X) RJ-45 fast Ethernet ports support
auto-negotiation.
Default Setting :
Speed: auto
PoE P.D. Port ETH2 of IAP-620+ compliant with IEEE802.3af PoE specifications
ANT. Reversed SMA connector for high gain external antenna.

IAP-620 Series User’s Manual
ORingIndustrialNetworkingCorp. 10
IAP-620 IAP-620+
1 2.4/5 GHz antenna with typical 3.0 dBi antenna.
2 LED for PoE power and system status. When the PoE power links, the green LED will
be light on.
3 LED for PWR1 and system status. When the PWR1 links, the green LED will be light
on.
4 LED for PWR2 and system status. When the PWR2 links, the green LED will be light
on.
5 LED for Fault Relay. When the fault occurs, the amber LED will be light on.
6 10/100Base-T(X) Ethernet ports. (IAP-620+ contains P.D. function of PoE)
7 LED for Ethernet ports status.
8 LED for WLAN link status.
9 LED for WLAN signal strength..

IAP-620 Series User’s Manual
11 ORingIndustrialNetworkingCorp.
3.2 Front Panel LEDs
LED Color Status Description
P.O.E.
(IAP-620+) Green/Red
Green On PoE power connected.
Green blinking Device been located
Red blinking Indicates an IP conflict, or
DHCP or BOOTP server did
not respond properly
PWR1 Green/Red
Green On DC power 1 activated.
Green blinking Device been located
Red blinking Indicates an IP conflict, or
DHCP or BOOTP server did
not respond properly
PWR2 Green/Red
Green On DC power 2 activated.
Green blinking Device been located
Red blinking Indicates an IP conflict, or
DHCP or BOOTP server did
not respond properly
Fault Amber On Fault relay. Power failure or
Port down/fail.
WLAN Green On WLAN activated.
Blinking WLAN Data transmitted.
WLAN Strength Green On
WLAN signal strength.
1<25%, 2<50%, 3<75%,
4<100%
10/100Base-T(X) Fast Ethernet ports
10Mbps
LNK/ACT Amber On Port link up at 10Mbps.
Blinking Data transmitted.
100Mbps
LNK/ACT Green On Port link up at 100Mbps.
Blinking Data transmitted.

IAP-620 Series User’s Manual
ORingIndustrialNetworkingCorp. 12
3.3 Bottom Panel
The bottom panel components of IAP-620 / 620+ are showed as below:
1.Terminal block includes: PWR1, PWR2 (12 ~ 48V DC) and Relay output (1A@24VDC).
2.Reset bottom. Push the button 3 seconds for reset; 5 seconds for factory default.
Reset
PWR-2 PWR-1
V2+V2- Relay V1+V1-
Reset Button
Terminal Block Power-2 Input
Relay Output Pin
Terminal Block Power-1 Input
Bottom panel of IAP-620 / 620+
3.4 Rear Panel
The rear panel components of IAP-620 / 620+ are showed as below:
1. Screw holes for wall mount kit.
2. DIN-Rail kit
Rear panel of IAP-620 / 620+
12

IAP-620 Series User’s Manual
13 ORingIndustrialNetworkingCorp.
Cables and Antenna
4.1 Ethernet Cables
The IAP-620/IAP-620+ WLANAP has two 10/100Base-T(X) Ethernet ports.
According to the link type, theAP use CAT 3, 4, 5,5e UTP cables to connect to any other
network device (PCs, servers, switches, routers, or hubs). Please refer to the following
table for cable specifications.
Cable Types and Specifications
Cable Type Max. Length Connector
10Base-T Cat. 3, 4, 5 100-ohm UTP 100 m (328 ft) RJ-45
100Base-T(X) Cat. 5 100-ohm UTP UTP 100 m (328 ft) RJ-45
4.2 100Base-T(X)/10Base-T Pin Assignments
With 100Base-T(X)/10Base-T cable, pins 1 and 2 are used for transmitting data, and
pins 3 and 6 are used for receiving data.
RJ-45 Pin Assignments
Pin Number Assignment
1 TD+
2 TD-
3 RD+
4 P.O.E. power input +
5 P.O.E. power input +
6 RD-
7 P.O.E. power input -
8 P.O.E. power input -
The IAP-620/IAP-620+ supports auto MDI/MDI-X operation. You can use a
straight-through cable to connect PC and AP. The following table below shows the
10Base-T/ 100Base-T(X) MDI and MDI-X port pin outs.

IAP-620 Series User’s Manual
ORingIndustrialNetworkingCorp. 14
MDI/MDI-X pins assignment
Pin Number MDI port MDI-X port
1 TD+(transmit) RD+(receive)
2 TD-(transmit) RD-(receive)
3 RD+(receive) TD+(transmit)
4 P.O.E. power input + P.O.E. power input +
5 P.O.E. power input + P.O.E. power input +
6 RD-(receive) TD-(transmit)
7 P.O.E. power input - P.O.E. power input -
8 P.O.E. power input - P.O.E. power input -
Note: “+” and “-” signs represent the polarity of the wires that make up each wire pair.
4.3 Wireless Antenna
2.4GHz/5.8GHz antenna is used for IAP-620/IAP-620+ and connected with a reversed SMA
connector. External RF cable and antenna also can be applied with this connector.

IAP-620 Series User’s Manual
15 ORingIndustrialNetworkingCorp.
Management Interface
5.1 Explore IAP-620/IAP-620+
5.1.1 Open-Vision_Commander
IAP-620/IAP-620+ can also be configure through ORing’s Windows utility Open-Vision
Step 1: Open the commander and click “Discover”, the AP devices will show on the list.
Step 2: Choose your access point, and it will show the AP function tree. Simultaneity,
you can login and then set theAP.
User interface of commander

IAP-620 Series User’s Manual
ORingIndustrialNetworkingCorp. 16
5.2 UPnP Equipment
Step 1: To check whether the UPnP UI of the computer is connected to the
IAP-620/IAP-620+, go to Control Panel > Add or Remove Programs > Windows
Components Wizard > Networking Servers > UPnP User Interface and pitch on the
UPnP User Interface.
UPnP configuration page
Step 2: At the right-below corner of the computer, you will find a sign of the UPnP
equipment.

IAP-620 Series User’s Manual
17 ORingIndustrialNetworkingCorp.
Step 3: Click the sign of the UPnP equipment, then you will find the UPnP equipment in the
network neighborhood.
Step 4: Right click the UPnP equipment to choose “Properties”, it will show as the following
pictures:
Step 5: Right click the UPnP equipment or double click the UPnP equipment to transfer; it
will go to the web page.
5.3 Configuration by Web Browser
This section introduces the configuration by Web browser.
5.4 About Web-Based Management
An embedded HTML web site resides in flash memory in the system. It contains
advanced management features and allows you to manage the AP from anywhere on the
network through a standard web browser such as Microsoft Internet Explorer.
The Web-Based Management function supports Internet Explorer 5.0 or later. It is based
on Java Applets with an aim to reduce network bandwidth consumption, enhance access
speed and present an easy viewing screen.
Note: By default, IE5.0 or later version does not allow Java Applets to open sockets. You need to explicitly modify

IAP-620 Series User’s Manual
ORingIndustrialNetworkingCorp. 18
the browser setting in order to enable Java Applets to use network ports.
Through the front section’s information, you will see as follows, enter your user name
(admin) and your password (admin), and then click OK to continue.
Login screen
For security reasons, we strongly suggest you change the password. Click on System
Tools > Administrator and modify the password.
5.5 Main Interface
The Home screen will appear. Please click “Run Wizard” to go to the Home > Setup
Wizard page to quick install the AP.
Main interface

IAP-620 Series User’s Manual
19 ORingIndustrialNetworkingCorp.
5.5.1 Basic Setting
Setting Operation Mode
Operation mode interface
The following table describes the labels in this screen.
Label Description
AP This mode provides Access Point services for other wireless
clients.
AP-Client The AP-Client function provides a 1-to-N MAC address mapping
mechanism such that multiple stations behind the AP can
transparently connect to the other AP even they didn’t support
WDS.
Client In this mode the AP functions as a wireless client to connect to
other AP, thus provides transparent connection between Ethernet
& wireless port. This mode provides no Access Point services but
with 802.1X supported.
Bridge This mode provides Static LAN-to-LAN Bridging functionality.
The static LAN-to-LAN bridging function is supported through
Wireless Distribution System (WDS).
In each mode, the IAP-620/IAP-620+ forwards packet between its Ethernet interface and
wireless interface for wired hosts on the Ethernet side, and wireless hosts on the wireless
side.

IAP-620 Series User’s Manual
ORingIndustrialNetworkingCorp. 20
Setting WDS (Bridge Mode)
WDS setting interface
This type of wireless link is established between two IEEE 802.11 access points.
Wireless packets transmitted along the WDS link comply with the IEEE 802.11 WDS
(Wireless Distribution System) format at the link layer.
Point-to-Point WDS Link
The following table describes the labels in this screen.
Label Description
WDS Mode This mode provides Static LAN-to-LAN Bridging functionality.
The static LAN-to-LAN bridging function is supported through
Wireless Distribution System (WDS).
Peer MAC Address Set the Mac address of other access point(s). Simultaneity,
choose on “Enable”.
First of all, if APs link with WDS mode, it should obey the following rules:
1. LAN IPAddress should set different IP in the same network.