Oster Pro BLSTEPH User manual

User Manual
www.oster.com
Oster®Pro Series Blender with High
Performance Motor
Model: BLSTEPH
Oster®Pro Series Blender with
High Performance Motor
BLSTEPH_22EM1.indd 1BLSTEPH_22EM1.indd 1 2022/12/12 上午9:562022/12/12 上午9:56

2
1
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be
followed to reduce the risk of fire, electric shock, and/or injury to persons
including the following:
1. Read all instructions before using this product.
2. To protect against electric shock, do not place or immerse cord, plugs, or
appliance in water or other liquid.
3. This appliance is not intended for use by children or by persons with
reduced physical, sensory, or mental capabilities, or lack of experience
and knowledge. Close supervision is necessary when any appliance is
used near children. Children should be supervised to ensure that they do
not play with the appliance. Keep the appliance and its cord out of reach
of children.
4. Never leave appliance unattended when in use.
5. Unplug from outlet when not in use, before putting on or taking off
parts and before cleaning. Allow to cool before putting on or taking off
parts, and before cleaning. To disconnect, turn any control to OFF, then
unplug power cord from outlet. To unplug, grasp the plug and pull from
the outlet. Never pull from the power cord.
6. Avoid contacting moving parts. Avoid inadvertent contact with the touch
screen.
7. Flashing light indicates ready to operate (models with stand-by mode).
Avoid any contact with blades or moveable parts.
8. Do not operate any appliance with a damaged cord or plug or after the
appliance malfunctions, or has been damaged in any manner. Do not
attempt to replace or splice a damaged cord. Return appliance to the
manufacturer (see warranty) for examination, repair or adjustment.
9. For appliances with markings on plug blade: This appliance has
important markings on the plug blade. The attachment plug or entire
cordset (if plug is molded onto cord) is not suitable for replacement. If
damaged, the appliance shall be replaced.
10. The use of attachments, including canning jars, not recommended or
sold by the manufacturer may cause fire, electric shock or injury.
11. Do not use outdoors or for commercial purposes.
12. Do not let cord hang over edge of table or counter, or touch hot surfaces,
including the stove.
13. Keep hands and utensils out of container while blending to reduce the
risk of severe injury to persons or damage to the blender. A scraper may
be used but must be used only when the blender is not running.
14. Blades are sharp. Handle carefully, especially when removing the blades
from the container, emptying the container and during cleaning.
15. To reduce the risk of injury, never place cutter-assembly blades on base
without jar properly attached.
16. Always hold container while operating the appliance. If the container
should turn when the motor is turned ON, switch appliance OFF
immediately and tighten the container in the threaded bottom.
17. Always operate blender with cover in place. Always wait until all moving
parts have stopped before removing any lid or cover.
18. When blending hot liquids, remove center piece of two-piece cover (if
a two-piece cover is provided). Beware of steam. Do not blend boiling
liquids.
19. Do not use appliance for other than intended use. Misuse can cause
injuries. Always use appliance on a dry, stable, level surface. Never fill
beyond the MAX fill line.
For containers with no lids or vents (when inserted in the blender), such as
personal Blend and Go containers:
20. Do not blend carbonated, hot or boiling liquids and ingredients, as this
may create pressure buildup. Only blend non-carbonated liquids and
ingredients that are at room temperature or cooler. If the container is
warm to the touch, allow to cool before opening.
21. Do not use the blender for longer than 1 minute at a time to avoid heat
and pressure buildup. Allow to cool for 1 minute between cycles.
For appliances with food processor or food chopper attachments:
22. Keep hands and utensils away from moving blades or discs while
processing or chopping food to reduce the risk of severe injury to persons
or damage to the food processor or chopper. A scraper may be used but
must be used only when the food processor or chopper is not running.
23. To reduce the risk of injury, never place cutting blade or discs on base
without first putting container properly in place.
24. Be certain cover is securely locked in place before operating appliance.
25. For food processors: Never feed food by hand. Always use food pusher.
26. Do not attempt to defeat the cover interlock mechanism.
SAVE THESE INSTRUCTIONS
HOUSEHOLD USE ONLY
• The maximum rating marked on the product is based on the attachment that draws
the greatest load. Other attachments may draw less power.
North American models with polarized plugs:
This symbol has been placed in specific areas of the User Guide portion of
this book. Its purpose is to help you easily identify instructions that
require your special attention.
POLARIZED PLUG
This appliance has a polarized plug, (one blade is wider than
the other). As a safety feature to reduce the risk of electrical
shock, this plug is intended to fit in a polarized outlet only one
way. If the plug does not fit fully in the outlet, reverse the plug.
If it still does not fit, contact a qualified electrician. Do not
attempt to defeat this safety feature or modify the plug in any
way. If the plug fits loosely into the AC outlet or if the AC outlet feels warm do
not use that outlet.
BLSTEPH_22EM1.indd 1-2BLSTEPH_22EM1.indd 1-2 2022/12/12 上午9:562022/12/12 上午9:56

4
3
Welcome
Congratulations on your new Oster®Pro Series Blender. Your Oster®blender
will allow you to create delicious smoothies, milkshakes, salsas and much
more at the touch of a button! If you have any comments, questions or
inquiries about this product, please call 1-800-334-0759. Your product
includes the following features and benefits:
• Intuitive touchscreen display for a modern take on traditional blending
• 4 Auto Programs for Smoothies, Milkshakes, Frozen Drinks, and Salsas
• Select model has 5th auto program for Self Clean
• Manual modes for low, medium, high, and pulse functionality
• 9-Cup XL Tritan jar – dishwasher safe & BPA free
• 3-Inch, 6-point Stainless Steel blade
• Dual direction blade technology reduces food jamming
• Tamper tool accessory to assist in blending tough ingredients
• Select models include food processor, blend-n-go cup, and mini jar
accessories
• 3-year satisfaction guarantee
For Best results, carefully read the instruction manual before using this
appliance.
Learning About the Oster Pro Series with High Performance
Motor
1. Filler Cap / 2 Ounce Measuring Cup: – For
precise measurements when blending recipes.
Remove the cap to add ingredients during the
blending process and allow steam to escape
when blending hot foods.
2. Jar lid – Seals the blender jar.
a. Includes flexible latching tabs which hold lid
to blending jar for a secure fit
3. Tritan Jar – 9 cup capacity, BPA free and
dishwasher safe.
4. Sealing Ring
a. Sealing ring with locking tabs fit snugly into
grooves of the jar bottom to prevent blade
from falling out unintentionally during
cleaning
5. Blade
6. Threaded Jar Bottom – Advanced design for
simple assembly of jar.
7. Motor Base
8. Touchscreen Controls
a. Power button turns the product on and off
i. Hold 1 second for power
ii. Blender functions will not appear unless
unit is powered on
iii.When in-use, selected function will
remain highlighted and remaining
functions will dim in appearance
b. Auto program settings
i. Select desired setting and your Oster
Pro Series Blender will cycle through the
program delivering expert results at the
touch of a button
ii. Unit will stop automatically after running
through the cycle
iii.Select from Smoothies,
Milkshakes, Frozen Drinks,
and Salsas
c. Manual speeds – low, medium,
and high
i. Select speed to run blender
and select again to stop
d. Pulse button – Press and hold to
pulse, release to stop.
b
1
2
3
4
5
6
7
8
c
a
d
BLSTEPH_22EM1.indd 3-4BLSTEPH_22EM1.indd 3-4 2022/12/12 上午9:562022/12/12 上午9:56

6
5
9-Cup XL Tritan Jar Assembly
1. Place the agitator (blade) assembly onto the threaded jar bottom.
2. Place the locking sealing ring on top of the blade assembly. Ensure the
locking tabs fit snugly into the groove at the bottom of the jar bottom.
3. Install the jar nut, seal, and blade assembly onto the jar.
4. Put the ingredients into the jar.
5. Secure the lid and filler cap.
6. Place the jar onto the base.
7. Plug the power cord into a standard household 120/127-volt, 60 hz. AC outlet.
You are now ready to start.
ALWAYS PLACE HAND ON CONTAINER COVER WHILE OPERATING
BLENDER.
Using the Touchscreen Controls
1. Plug in the blender. Once plugged in, press and hold the “ ” button for one
second to turn the blender on.
2. Select setting and blend ingredients to desired consistency.
NOTE: Control panel lists function as well as desired outcome.
3. Press Power Button to stop and turn off blender.
4. Hold and release PULSE for ice crushing and chopping. Repeat as
needed.
Using the Pre-Programmed Settings
1. Press and hold the button for one second to turn the blender on. The
power light will light up indicating the blender is active and ready to use.
The light will stay on while the motor is running.
2. Order of programs as they appear on the blender
1. Smoothie
2. Milkshake
3. Frozen Drink
4. Salsa
5. Auto Clean
3. To change your selection, select any function on the blender. To stop blender
from operating, select the same function twice.
1. For example, if you are running the Smoothie function and want to the
blender to stop, select the smoothie function again.
4. Once the program is complete the blender will automatically stop.
5. Press and hold the button for one second to turn off the blender. The
blender is pre-programmed to turn off automatically if not used for a period
of several minutes. All lights will turn off when the unit automatically
powers down.
Using the Manual Controls
The Manual Controls include:
LOW
MEDIUM
HIGH
PULSE
Use these controls for personal recipes or to continue blending after a
Programmed Setting is finished.
1. Press and hold the button for one second to turn on the blender. The
power light shines bright indicating the blender is active and ready to use.
The light will stay on when the motor is running.
2. Put the ingredients into the jar.
3. Secure the lid and the filler cap.
Pressing any speed setting will interrupt the active function. e.g. blender is
running on “LOW”, pressing “HIGH” button will change the speed to “HIGH”.
Or pressing “LOW” a second time will turn the blender to the active and ready
to use screen (flashing power button ).
Locking
Sealing Ring Blade
BLSTEPH_22EM1.indd 5-6BLSTEPH_22EM1.indd 5-6 2022/12/12 上午9:562022/12/12 上午9:56

8
7
Caring for Your Product
After Use
1. Turn the blender off and unplug from outlet. Lift the jar straight up from
the base, remove the lid and empty the jar.
2. If necessary, use a rubber spatula to scrape foods away from the sides of the
jar.
Cleaning
WARNING: Blades are sharp. Handle carefully.
CAREFULLY release the blade from the bottom of the jar by turning the
threaded jar bottom counterclockwise. The jar lid, filler cap and blade are
dishwasher safe. Use the top rack of the dishwasher for the jar lid, filler cap,
and blade. Place sealing ring into bottom basket of dishwasher.
You can also wash the parts in warm, soapy water. Rinse well and dry. Wipe
the base with a soft, damp cloth to clean. Never submerge the blender base in
a liquid.
Check the parts as you put them back together.
TIP: Disassembly of jar bottom and blade
recommended to ensure proper cleaning.
Storing
Reassemble the blender for storage. Leave the lid
open a gap so no odors are retained.
NOTICE: Never put the jar, or any other parts, in a
microwave oven. Never store foods or drinks in the jar.
Servicing
This appliance has no user serviceable parts. Any servicing beyond the
cleaning described in the Cleaning section should be performed by an
authorized service representative only.
If repairs are needed, send your appliance only to an authorized OSTER®
Appliance Service Center. Replacement parts are available on www.oster.com
or call 1-800-334-0759.
Blend-N-Go®Smoothie Cup Accessory (Select Models
Only)
NOTE: For proper installation onto Blender Motor base, make sure locking
lever rotates past the anti-rotation tabs on the smoothie cup. Avoid pressing
lever during threading or unthreading from the smoothie cup.
A. Locking Lever
B. Anti-Rotation Tabs
C. Blender base
NOTE: Blend-N-Go®Smoothie cup attachment is only compatible with grey
threaded jar bottom.
A
C
Figure 1
Smoothie Cup
with Drink Lid
Smoothie Cup
& Threaded
Jar Bottom NOTE: Threaded Jar base
with Locking Lever MUST
be used with Smoothie cup
attachment
Figure 2
B
BLSTEPH_22EM1.indd 7-8BLSTEPH_22EM1.indd 7-8 2022/12/12 上午9:562022/12/12 上午9:56

10
9
Using your Blend-N-Go®cup with your Oster Pro Series
Blender
Before washing ensure the blender is off and unplugged. Wash all components
except blender base with soapy water with a soft sponge and a bottle brush. Do
not use abrasive cleansers or sponges for cleaning. Rinse well and dry. Parts are
also dishwasher safe. Do not blend hot liquids.
Place desired ingredients into smoothie cup according to the following order:
Liquids, fresh ingredients, frozen fruit, ice, yogurt and ice cream.
(Cut all firm fruits, vegetables and other foods into pieces no larger than 1/2-inch
(1.25 cm) by 2 inches (5.0 cm).
• Place Blade into Threaded Jar Bottom or adapter.
• Place sealing ring over blade assembly. Carefully press and tuck sealing ring into
locking groove.
• Place blade assembly into cup.
• Be sure the Integrated Blade Assembly is tightened to the jar before using.
• Place cup assembly onto Blender base.
• Hold cup in position. Operate Blender according to the instructions in your
Blender User Manual. Blend until desired consistency.
• Place lid on cup and turn clockwise to tighten.
Enjoy your blended drink!
Blend-N-Go®Mini Jar Accessory (Select Models Only)
NOTE: For proper installation onto Blender Motor base, make sure locking
lever rotates past the anti-rotation tabs on the mini jar.
A. Locking Lever
B. Blender base
NOTE: Mini jar attachment is only compatible with grey threaded jar bottom
with locking lever.
NOTE: Do not blend hot liquids. Cut all firm fruits, vegetables, and other foods
into pieces no larger than 1/2-inch (1.25 cm) by 2 inches (5.0 cm).
TIP: Recommended foods for blending in mini jar include coffee beans, baby
food, small batches for dips and purees.
A
B
Figure 2Figure 1
Mini Jar with
Drink Lid
Mini Jar &
Threaded jar
bottom with
locking lever NOTE: Threaded Jar base with
Locking Lever MUST be used
with Mini Jar attachment
Figure 3
BLSTEPH_22EM1.indd 9-10BLSTEPH_22EM1.indd 9-10 2022/12/12 上午9:562022/12/12 上午9:56

12
11
Food Processor Accessory (Select Models Only)
Food Pusher – Use to safely push
ingredients into Slicing/Shredding
Disk.
Cover – The feed tube allows the
addition of ingredients while processing.
Plastic Center Hub
WARNING: The blade is very
sharp, handle carefully.
S Blade – Specially designed for
chopping and mincing. Grasp the
plastic Center Hub when handling the
Blade.
Bowl – 5-cup capacity allows for fast
processing of hard-to-chop foods.
Blade Shaft – For use with Slicing/
Shredding Disk.
Adaptor – Transfers the power
of your Motor Base to the Food
Processor Accessory.
Motor Base
Before Using for the First Time –
After unpacking, disassemble unit before using for the first time.
Wash all parts (except Adaptor) in warm, soapy water.
Rinse and dry immediately.
CAUTION: DO NOT IMMERSE ADAPTOR IN ANY LIQUID.
Cover
Food Pusher
Bowl
Blade Shaft
Plastic Center Hub
S Blade
Adaptor
Motor Base
Assembling and Using Your Food Processor
1. Before assembly, make sure Adaptor is operating correctly. Unplug Motor
Base during assembly.
2. Place Adaptor in bowl and turn counterclockwise to lock.
3. Place Bowl with Adaptor on Motor Base.
Chop or Mince
4. Hold S Blade by the plastic Center Hub and place over post of Bowl.
CAUTION: Blade is very sharp, handle carefully. Rotate the S Blade to make
certain it is seated on the post as far as it will go. Always place S blade in
Food Processor before adding ingredients.
5. Place food in Processing Bowl. Food to be processed should always be cut
into 1-inch (2.5 cm) pieces.
6. Using alignment marks on the lid, place cover on bowl and press down
firmly while turning counterclockwise to lock.
DO NOT OPERATE UNIT UNLESS COMPLETELY ASSEMBLED
7. Turn unit “ON.” (Select Pulse, Low, or Med setting on the Motor Base.)
ALWAYS HOLD FOOD PROCESSOR FIRMLY WITH ONE HAND
WHEN STARTING UNIT AND WHEN PROCESSING. Process until
desired results are achieved by running the unit continuously or Fast Pulsing.
Fast Pulsing is the technique used to control the size of the food being
processed with the Food Processor Accessory. Press and release the Pulse
button very quickly. Refer to Processing Chart for proper techniques and end
results.
NOTE: Only the “Salsa” auto program setting is functional when Food
Processor is attached.
Slice or Shred
8. Place Blade Shaft over post. Place Slicing/Shredding Disk over Blade Shaft
with the blade of your choice facing up. CAUTION: Blade is very sharp,
handle carefully.
9. Using alignment marks on the lid, place cover on bowl and press down
firmly while turning counterclockwise to lock.
10.Load the feed tube with ingredients before turning the Food Processor
“ON”.
BLSTEPH_22EM1.indd 11-12BLSTEPH_22EM1.indd 11-12 2022/12/12 上午9:562022/12/12 上午9:56

14
13
11.Rest the Food Pusher in the feed tube. Turn unit “ON”. (Select medium
speed setting.) While holding the Food Pusher with one hand and the feed
tube in the other, push gently down on the Food Pusher. Always use the
Food Pusher to yield more evenly sliced or shredded foods. – NEVER USE
YOUR FINGERS. When finished, turn the unit “OFF”.
NOTE: Med - High Manual settings are recommended for slicing and shredding.
How To Disassemble
1. Turn unit “OFF” and unplug Motor Base.
2. Always wait for the S Blade or Slicing/Shredding Disk to stop spinning.
3. Remove Food Processor Accessory from Motor Base.
4. Turn Cover clockwise to remove from Bowl.
5. Remove S Blade or Disk carefully. Be careful not to let Blade or Disk fall out
of the container. The cutting edges are very sharp. Scrape any remaining
food from the Blade and Processing Bowl.
6. Unlock Bowl from Adaptor by turning Bowl clockwise.
Cleaning
Unplug Motor Base Before Cleaning.
WARNING: Do Not Immerse Adaptor in Water. Always Remove Adaptor
from processor Bowl before cleaning.
WARNING: Keep S Blade and Disk out of the reach of children. Store the S
Blade and Disk in the Bowl or in a convenient, safe location when not in
use. This Blade and Disk should be treated with the same caution as a sharp
knife.
Remove stains caused by processing large amounts of carrots or similar
vegetables with baking soda. Rinse stained parts in water and sprinkle with
baking soda. Rub with a soft, damp cloth. Rinse and dry. Do not use abrasive
cleaners on any parts.
Maintenance
This unit is designed with a safety interlock. The interlock requires that the
Cover be in place before the blade will rotate. (The interlock does not control
operation of the Motor.) To ensure that the interlock is operating correctly, hold
the Adaptor and rotate the Drive Shaft several turns. The metal Star Drive on
the bottom of the Adaptor should NOT turn. If it does turn, DO NOT USE.
Return the unit to an authorized service facility for repair. DO NOT USE THE
INTERLOCK FEATURE AS A SUBSTITUTE for turning the power unit “OFF”
and unplugging the power unit before disassembling and cleaning. Never put S
Blade on Adaptor without Processor Bowl. Do not operate if the flexible seal is
damaged or missing. The safety interlock could become jammed.
Processing Tips
1. Cut all fruits and vegetables, cooked meats, fish, seafoods and cheeses into
pieces 1 inch or smaller.
2. Always hold hand firmly on the Cover when starting and running Motor.
3. Do not process hot liquids or frozen foods.
4. Do not process whole spices (except peppercorns) such as nutmeg or
cinnamon. They may cause damage to the surface of the Processor Bowl.
5. Process the hardest foods first, using only a few Fast Pulses to begin
chopping. Add more delicate foods and continue to process using the Fast
Pulse technique. The harder foods will continue to be chopped along with
the softer foods.
6. Processing of Parmesan cheese, dried dates or other extremely hard foods is
not recommended. If a knife cannot easily pierce the food, it should NOT be
processed in the Food Processor Accessory.
7. The Food Processor Accessory is not designed to whip cream, whip egg
whites or process dough. Use a standard mixer for those tasks.
8. If liquid leaks from Cover, there is too much liquid in the recipe. Adjust the
liquid level to prevent leakage.
9. The temperature of cheese will affect how it processes. Cheese for spreads
should be at room temperature for a smooth, creamy texture. “Grated”
cheese should be refrigerator cold.
10.Large, harder pieces of food can be processed with several Fast Pulses to
coarsely chop. Then process continuously for a fine texture.
Only the “Food Chop/Salsa” Pre-Programmed setting is functional when Food
processor is attached.
To Convert a Recipe
1. Total the amount of dry and liquid ingredients. If the total exceeds 5 cups,
decide if the recipe can be made easily in batches. Do not attempt to process
large recipes.
2. If total is under 1 cup (250 ml), process dry ingredients or the most finely
chopped foods first.
3. Then add remaining ingredients and combine with several Fast Pulses to mix
together.
BLSTEPH_22EM1.indd 13-14BLSTEPH_22EM1.indd 13-14 2022/12/12 上午9:562022/12/12 上午9:56

16
15
3 YEAR SATISFACTION GUARANTEE
Sunbeam Products, Inc. or if in Canada, Newell Brands Canada ULC (collectively “Sunbeam”)
warrants that for a period of three years from the date of purchase, this product (and ten years
for the included All Metal Drive) will be free from defects in material and workmanship. Sunbeam
Products, Inc., at its option, will repair or replace, free of charge, this product or any component
of the product found to be defective during the warranty period. Replacement will be made with
a new or remanufactured product or component at no cost to the consumer. If the product is
no longer available, replacement may be made with a similar product of equal or greater value.
This is your exclusive warranty. Do NOT attempt to repair or adjust any electrical or mechanical
functions on this product. Sunbeam Products, Inc. reserves all rights to decline coverage if the
defect or damage was caused by unauthorized components or service. This warranty is valid for
the original retail purchaser from the date of initial retail purchase and is not transferable. Keep
the original sales receipt. Proof of purchase is required to obtain warranty performance. Dealers,
service centers, or retail stores selling Sunbeam Products, Inc. products do not have the right to
alter, modify or any way change the terms and conditions of this warranty. This warranty does not
cover normal wear of parts or damage resulting from any of the following: negligent use or misuse
of the product, use on improper voltage or current, use contrary to the operating instructions,
disassembly, repair or alteration by anyone other than Sunbeam Products, Inc. or an authorized
Sunbeam Products, Inc. service center. Sunbeam Products, Inc. expressly excludes from this
warranty and denies liability for defects or damage caused by repair or alteration by anyone other
than Sunbeam Products, Inc. or an authorized Sunbeam Products, Inc. service center. Further, the
warranty does not cover: Acts of God, such as fire, flood, hurricanes and tornadoes.
No terms of this warranty may be construed to apply to non-warranty service and maintenance.
Accordingly, Sunbeam Products, Inc. also denies liability for defects and damage caused by repair
or alteration outside the terms of this warranty.
What are the limits on Sunbeam’ Liability?
Sunbeam shall not be liable for any incidental or consequential damages caused by the breach
of any express, implied or statutory warranty or condition. Except to the extent prohibited by
applicable law, any implied warranty or condition of merchantability or fitness for a particular
purpose is limited in duration to the duration of the above limited warranty. Sunbeam disclaims
all other warranties, conditions or representations, express, implied, statutory or otherwise.
Sunbeam shall not be liable for any damages of any kind resulting from the purchase, use or
misuse of, or inability to use the product including incidental, special, consequential or similar
damages or loss of profits, or for any breach of contract, fundamental or otherwise, or for any
claim brought against purchaser by any other party. Some provinces, states or jurisdictions do
not allow the exclusion or limitation of incidental or consequential damages or limitations on
how long an implied warranty lasts, so the above limitations or exclusion may not apply to you.
This limited warranty gives you specific legal rights, and you may also have other rights that
vary from province to province, state to state or jurisdiction to jurisdiction.
How to Obtain Satisfaction Guarantee and/or Limited Warranty Service
In the U.S.A.
If you have any question regarding this guarantee or limited warranty or would like to obtain
guarantee or limited warranty service, please call 1-800-334-0759 and a convenient service
center address will be provided to you.
In Canada
If you have any question regarding this guarantee or limited warranty or would like to obtain
guarantee or limited warranty service, please call 1-800-667-8623 and a convenient service
center address will be provided to you.
In the U.S.A., this guarantee and limited warranty is offered by Sunbeam Products, Inc. located
in Boca Raton, Florida 33431. In Canada, this guarantee and limited warranty is offered by
Newell Brands Canada ULC, located at 20 B Hereford Street, Brampton, Ontario L6Y 0M1. If you
have any other problem or claim in connection with this product, please write to the Consumer
Service Department.
PLEASE DO NOT RETURN THIS PRODUCT TO ANY OF THESE
ADDRESSES OR TO THE PLACE OF PURCHASE.
For inquiries regarding recycling and proper disposal of this product,
please contact your local waste management facility.
BLSTEPH_22EM1.indd 15-16BLSTEPH_22EM1.indd 15-16 2022/12/12 上午9:562022/12/12 上午9:56

For product questions contact:
Sunbeam Consumer Service
USA : 1.800.334.0759
Canada : 1.800.667.8623
www.oster.com
©2022 Sunbeam Products, Inc. All rights reserved.
In the U.S., distributed by Sunbeam, Products, Inc., Boca Raton, FL 33431
In Canada, imported and distributed by Newell Brands Canada ULC, Brampton (Ontario)
L6Y 0M1.
TritanTM is a trademark of Eastman Chemical company used with permission.
Printed in Mexico.
BLSTEPH_22EM1_GCDS-JC PN. 2171991 / NWL0001415967
BLSTEPH_22EM1.indd 17BLSTEPH_22EM1.indd 17 2022/12/12 上午9:562022/12/12 上午9:56