Outdoor GreatRoom Company NAPA-VALLEY-1224-K User manual

1 | P a g e
Napa Valley Fire Pit Table
Installation Instructions
For Models:
NAPA-VALLEY-1224-K, NV-1224-BRN-K, NV-1224-BLK-K, NV-1224-GRY-K,
NV-1224-BLK-W-K

2 | P a g e
Contents
Contents……………………………………………………..2
Required Tools…………………………………………..3
Placing and Assembling the
Table…………………….………………………………………4
Gas Connection………………………….…………….5
Igniter Installation…………….………………………...6
90221:D 4.28.2014

3 | P a g e
Required Tools
Utility Knife
To cut and remove packaging
2 Open Ended Wrenches
To make gas connections
Leather Gloves
To protect hands from rough edges found on the coffee
table.
One (1) AAA Battery (not included)
Required for piezoelectric igniter installation.
Electric screw gun with Phillips tip
Included:
Tabletop frame Base Tiles (x10)
Bracket (x4)
Screw (x16)

4 | P a g e
Placing and Assembling the Fire Pit table
1. Remove all components from packaging and
inspect for damage or missing parts.
2. Move the base to desired location and set into
place.
When locating your coffee table, refer to the
Crystal Fire manual and maintain clearance to
combustibles.
4. Line top up with base as shown.
Place brackets in locations shown (red
arrows below) and insert 4 screws
into each bracket.
3. Place top on base
as shown, making
sure it is centered in
both directions.
5. With top securely fastened to
base, set tiles into place.

5 | P a g e
Gas Connection
1. With proper orifice installed for the application
and metal flex hose attached (see burner
owner’s manual) set burner in base with burner
neck pointed toward the control panel.
2. Connect the incoming gas hose to the valve and
tighten securely. Repeat with flexible metal gas
line from the valve to the underside of burner.
It is not recommended to use Teflon tape or
pipe dope on the connection to the valve with
flare fittings.
LPG installations use the hose and regulator
provided with the burner.
For Natural Gas hookup information and any
other info not listed here consult your Crystal
Fire owner’s manual.
Attach incoming
gas here
Read and understand your Crystal Fire owner’s manual
before beginning burner hookups or using the device.

6 | P a g e
Igniter Installation
1. Make sure the valve is in the OFF
position
2. Unscrew sparker cap and hex nut (sparker
included with burner). Install as shown below.
(If your igniter only has one port on the back, please ignore
instructions for grounding. Your igniter is a self-grounding
model)

7 | P a g e
3. To properly install ignition system, an Ignition and Ground
wire need to be attached to the igniter box.
Start by plugging the black Ignition wire hanging from
the burner in to one side of the back of the igniter
(either side is fine).
Next; plug the Ground wire into the open port on the
igniter box.
Test system by depressing the button on the igniter. A
continuous repeating spark at the igniter on the burner
means everything is connected properly. Consult the
troubleshooting section of your crystal fire owner’s
manual if spark is weak, intermittent, or not present.
4. Once ignition system is grounded and gas
connections are secured and checked for
leaks, set the burner back into its original
position if it was removed during gas hookup.

8 | P a g e
Locating your Tank
1. Your tank should be positioned so that
the fuel can be shut off after each use.
2. Slide the tank into the framework past
the line shown below (table style may
vary). This is to allow the door to close
completely.
3. Confirm all hoses are clear and not
touching the burner.
Position tank behind this line

9 | P a g e
Door Installation
Finishing touches
Once fire pit is set up and in the desired position,
scatter decorative glass on burner surface forming
an even layer of beads.
DO NOT BURN WITHOUT GLASS OR OTHER
DECORATIVE SUBSTRATE PRESENT
Set door on supports and close.
Magnet will hold door in closed position.
Door support
*Exact model may differ

10 | P a g e
Warranty: Fire pit tables are covered under a 1-
year manufacturer’s warranty. Please visit
http://www.outdoorrooms.com/warranty-form
to register your product.
IMPORTANT
Please consult your Crystal Fire instruction manual for detailed
instructions and important information related to hooking up your
linear burner, including safety information, proper tightening of
connections with two wrenches and full burner setup and lighting
instructions.
DO NOT ATTEMPT TO INSTALL CF-1224 BURNER WITHOUT FIRST
CONSULTING THE MANUAL. IF YOU ARE UNSURE OF HOW TO
COMPLETE THE STEPS OUTLINED, CONSULT A QUALIFIED
TECHNICIAN
WARNING
After consulting the manual and following instructions, remember; before operating,
all gas connections must be fully checked for leaks