Outdoor GreatRoom Company Edison ED-20 User manual

1
Edison Fire Pit Table
Installation Instructions for Edison Fire Pit Table
ED-20

2
Contents
Required Tools…………………………….…..2
Included with your Fire Pit……………….3
Assembly Instructions………………….………4
Gas Connections………………………….…….6
Igniter Installation…………….……………...8
Position Your Tank………………………7
Finishing Touches……………………………7
Required Tools
Utility Knife
To cut and remove packaging
2 Open Ended Wrenches
Contents
Required Tools………………………………….........2
Included with your Fire Pit………………………..3
Assembly Instructions……………………………….4
CF-SPARKER Installation…………………..……….4
Supercast Top Placement……………………….…5
Gas Connections……………………………………….5
Thermocouple Installation…………….………….6
Electrode Installation…………….…………….…..7
Drawer Operation and
Propane Tank Installation……………………..….8
Fire Media Installation……………………….……..9
Burner Cover Installation………………..………..9
Operating Instructions..…………………………...10
Required Tools
Utility Knife
To cut and remove packaging
2 Open Ended Wrenches
To secure gas connections
Leather Gloves
To protect hands from glass and sharp edges during install
One AAA Battery (not included)
Required for electric spark igniter installation
Two people are recommended for
this installation
IMPORTANT
Please consult your Crystal Fire instruction manual for detailed
instructions and important information related to the burner
installation including: lighting and operating instructions, safety
information, and proper tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE BURNER WITHOUT
FIRST CONSULTING THE CRYSTAL FIRE OWNER’S MANUAL.
42493 REV C 11-22-19

3
Included with Your Fire Pit
Edison Metal Base
ED-20-BASE
Weathered Grey
Supercast Top
41-20-WG
Weathered Grey
Supercast Burner Cover
41-20-WG-COVER
20” Crystal Fire Plus Burner
CFP20
Ø1.25” Adhesive Foam Pads
(4X)
14-6904
Refer to Crystal Fire Manual for items included with crystal fire burners.

4
Do not discard any packaging until assembly is complete and
unit is tested. Keep all included manuals in a safe place for
future reference.
Warning: Exposed edges may be sharp, use leather gloves
when removing packaging and handling the base. Do not
remove protective cardboard packaging until you have
placed the fire pit in its desired final location.
Place base in desired final location.
Place on a hard, flat surface. Avoid soft surfaces and areas
that collect water.
Refer to Crystal Fire Plus Manual included with your Crystal
Fire Plus Burner for safety information regarding the
placement of your fire pit.
Assembly Instructions
Locate CF-SPARKER inside of Crystal Fire Plus burner box.
Remove CF-SPARKER cap and hex nut. Insert AAA battery
(not included) with + end out.
Install CF-SPARKER into control panel as shown below.
Depress CF-SPARKER button to test your sparker.
Un-packaging
Base Placement
1.
2.
CF-SPARKER Installation
3.
Locate and orient
sparker box on
control panel as
shown. Sparker box
must be installed
before burner valve.

5
Gas Connections
Read and understand your Crystal Fire Plus owner’s manual before beginning burner
hookups or using the device. Do not use Teflon tape or pipe dope on flare fittings.
See Crystal Fire Plus instructions for burner installation.
•All gas connections were completed at the factory.
Check all connections for leaks. If needed, tighten connection with
2 wrenches and re-check for leaks.
Attach burner valve to control panel with provided screws as shown
below. Ensure sparker box is installed before this step.
5.
Supercast Top Placement
Caution: Top is heavy, two people are required to lift and set into place.
•Remove burner cover before lifting the top to avoid
damage to the cover.
•Place adhesive foam pad on top of each leg.
•Carefully lower top onto base. Position top so it is
centered on the foam support pads.
4.

6
Thermocouple Installation
6.
•Refer to Crystal Fire Plus instruction manual for
detailed attachment of thermocouple.
•Attach thermocouple to burner valve as shown below.

7
Plug both BLACK wires hanging from the burner into
the back of the CF-SPARKER. If an orange wire is
present, do not use it. The orange wire is for Direct
Spark Ignition system only.
Test system by pushing the button on the igniter.
Consult the troubleshooting section of the Crystal Fire
Plus Burner Owner’s Manual if the spark is weak,
intermittent, or not present.
Electrode Installation
7.

8
Drawer Operation and Propane Tank Installation
•Pull the handle attached to the access drawer to slide access drawer out from
table. Pull drawer out until it stops along the slider track, as shown below.
With the propane tank valve and fire pit valve off, attach the propane regulator
to the propane tank. Hand tighten, do not use a wrench for this connection.
Ensure no hoses or wires are contacting the bottom of the burner.
Push the access drawer with propane tank back into the base, as shown below.
8.
NOTE: Over time the bearings
in the door glides may require
Re-greasing. Perform re-greasing
once a year to maintain the
smooth operation of the slides.
To re-grease the slides, spray any
spray lubricant, such as WD-40,
into the bearings as you slide the
drawer back and forth.
•Tilt propane tank and low into drawer from the side.

9
Scatter all included glass beads, lava rock, or other approved fire
media evenly across entire burner surface.
DO NOT OPERATE CRYSTAL FIRE BURNER WITHOUT INCLUDED GLASS
BEADS OR OTHER APPROVED FIRE MEDIA
• Carefully lay cover on top of burner.
Make sure burner is cool before attempting to place cover.
DO NOT OPERATE CRYSTAL FIRE BURNER WITH BURNER COVER IN PLACE
Fire Media Installation
9.
Burner Cover Installation
10.

10
Before operating your Edison fire pit, ensure all gas connections are
properly tightened and thoroughly leak checked. Refer to the Crystal
Fire Plus Manual for information on proper leak checking and other
critical safety information.
With the valve on the fire pit in the OFF
position, open the valve on the propane tank
or natural gas supply.
Double check to make sure there are no gas
leaks at the regulator or inlet side of the
valve. If leak is detected, immediately shut off
the gas supply and wait 5 minutes to allow
gas to dissipate. Fix any leaks before
proceeding.
Press the sparker button and hold, look and
listen for spark between electrode and
grounding rod.
While depressing the sparker, open the valve.
3. Turn valve to ON
2. Look/listen for spark
1. Depress sparker
If burner does not light after 10 seconds,
close the valve and wait 5 minutes to allow
gas to dissipate before attempting ignition
again.
Refer to the Crystal Fire Plus Manual included with your burner for
more detailed information on operation, maintenance, and safety
of your burner.
Operating Instructions
11.