Outdoor GreatRoom Company Alcott User manual

Alcott Fire Table
Installation Instructions for ALC-1224

2
Contents
Required Tools………………………………….........2
Included With Your Fire Pit……………………….3
Un-Packaging…………..……………………………….4
Base Placement………………………………………..4
CF-SPARKER Installation…………………………….5
Supercast Top Placement………………………….5
Gas Connections……………………………………….6
Electrode Installation………………………………..7
Thermocouple Installation………………………..7
Propane Tank Installation………………………….8
Fire Media Installation……………………………….9
Operating Instructions………………………………10
Required Tools
TWO people are required for this installation.
2 Open Ended Wrenches
To secure gas connections.
Leather Gloves
To protect hands from rough edges found on fire pit
during installation.
One AAA Battery (not included)
Required for electric spark igniter installation.
Utility Knife
To cut and remove packaging.
IMPORTANT
Please consult your Crystal Fire instruction manual for detailed
instructions and important information related to the burner
installation including: lighting and operating instructions, safety
information, and proper tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE BURNER WITHOUT
FIRST CONSULTING THE CRYSTAL FIRE OWNER’S MANUAL.
42482 REV-D 11-13-20

3
Included With Your Fire Pit
Alcott 1224 base
(Control Panel Installed)
ALC-1224-BASE
Antique Timber Supercast
Top and Burner Cover
3648-1224-AT & 3648-1224-
AT-C
1224 Crystal Fire Plus Burner
with Brown Trim
CFP-1224-BRN
Refer to Crystal Fire Plus Manual for items included with Crystal Fire Plus
burners.

4
Assembly Instructions
1. Un-packaging
Do not discard any packaging until assembly is
complete and unit is tested.
Keep all included manuals in a safe place for
future reference.
2. Base Placement
Place base in desired final location.
Place on a hard, flat surface. Avoid soft
surfaces and areas that collect water.
Refer to Crystal Fire Plus Manual included
with your Crystal Fire Plus Burner for safety
information regarding the placement of your
fire pit.

5
3. CF-SPARKER Installation
Locate CF-SPARKER inside of crystal fire
burner box.
Remove CF-SPARKER cap and hex nut. Insert
AAA battery (not included) with + end out.
Install CF-SPARKER into control panel as
shown below.
Depress CF-SPARKER button to test your
sparker.
4. Supercast Top Placement
Caution: Top is heavy, two people are
required to lift and set in to place. Remove
burner cover before lifting the top to avoid
damage to the cover.
Construction adhesive can be used to
permanently secure top to base, if desired.
Locate and orient
sparker box on
control panel as
shown. Sparker box
must be installed
before burner valve.

6
5. Gas Connections
See Crystal Fire Plus instructions for burner
installation.
All gas connections were completed
at the factory.
Check all connections for leaks. If needed,
tighten connection with 2 wrenches and
re-check for leaks.
Attach burner valve to control panel with
provided screws as shown below. Ensure
sparker box is installed before this step.
Carefully place burner into burner opening,
oriented as shown.
Electrode
Access door

7
7. Electrode Installation
Plug both BLACK wires hanging from the
burner into the back of the CF-SPARKER. If
an orange wire is present, do not use it. The
orange wire is for Direct Spark Ignition
system only.
Test system by pushing the button on the
igniter. Consult the troubleshooting section
of the Crystal Fire Plus Burner Owner’s
Manual, if the spark is weak, intermittent,
or not present.
6. Thermocouple Installation
•Refer to Crystal Fire Plus instruction manual
for detailed attachment of thermocouple.
•Attach thermocouple to burner valve as
shown below.

8
8. Propane Tank Installation
With the propane tank valve and fire pit valve
off, attach the propane regulator to the
propane tank. Hand tighten, do not use a
wrench for this connection.
Insert propane tank into base by sliding it past
the red dotted line shown above.
Ensure no hoses or wires are contacting the
bottom of the burner.
Replace the access door.

9
9. Fire Media Installation
•Scatter all included glass beads, lava
rock, or other approved fire media
evenly across entire burner surface.
DO NOT OPERATE CRYSTAL FIRE PLUS BURNER WITHOUT INCLUDED GLASS
BEADS OR OTHER APPROVED FIRE MEDIA
DO NOT OPERATE CRYSTAL FIRE PLUS BURNER WITH BURNER COVER IN PLACE

10
10. Operating Instructions
Before operating your Alcott 1224 fire pit, ensure all gas
connections are properly tightened and thoroughly leak checked.
Refer to the Crystal Fire Plus Manual for information on proper
leak checking and other critical safety information.
With the valve on the fire pit in the OFF
position, open the valve on the propane tank
or natural gas supply.
Double check to make sure there are no gas
leaks at the regulator or inlet side of the
valve. If leak is detected, immediately shut off
the gas supply and wait 5 minutes to allow
gas to dissipate. Fix any leaks before
proceeding.
Press the sparker button and hold, look and
listen for spark between electrode and
grounding rod.
While depressing the sparker, open the valve.
If burner does not light after 10 seconds,
close the valve and wait 5 minutes to allow
gas to dissipate before attempting ignition
again.
Refer to the Crystal Fire Plus Manual included with your burner
for more detailed information on operation, maintenance, and
safety of your burner.
3. Turn valve to ON
2. Look/listen for spark
1. Depress sparker