Outdoor GreatRoom Company NV-2424-K User manual

1 | P a g e
Napa Valley Fire Pit Table
48”x48” Model Installation Instructions
For Models:
NAPA-VALLEY-2424-K, NV-2424-BRN-K, NV-2424-BLK-K, NV-2424-GRY-K,
NV-2424-BLK-W-K

2 | P a g e
Contents
Contents……………………………………………………..2
Required Tools…………………………………………..3
Placing and Assembling the
Table…………………….………………………………………4
Gas Connection………………………….…………….6
Igniter Installation…………….………………………...7
90245:C 12.30.2014

3 | P a g e
Required Tools
Utility Knife
To cut and remove packaging
2 Open Ended Wrenches
To make gas connections
Leather Gloves
To protect hands from rough edges found on
the coffee table.
One (1) AAA Battery (not included)
Required for piezoelectric igniter installation.
Electric drill with Philips bit
Used to attach top to base
Included:
Bracket (x2)
Screw (x16)
Tabletop frame Base Tiles (x12)

4 | P a g e
Placing and Assembling the Fire Pit table
1. Remove all components from packaging and
inspect for damage or missing parts.
2. Move the base to desired location and set into
place.
When locating your coffee table, refer to the
Crystal Fire manual and maintain clearance to
combustibles.
3. Place a mounting
bracket flush with the
underside of tabletop
in the position shown.
Secure with 4 self-
drilling screws.
Repeat this step for
opposite end of table.
Insert Screws
Bracket locations

5 | P a g e
4. Set top assembly on
base, centering the newly-
installed brackets over the
framing as shown.
Insert 4 self-drilling screws
and repeat for opposite
side.
5. With top securely fastened to
base, set tiles into place.
*alternate model shown

6 | P a g e
Gas Connection
1. With proper orifice installed for the application
and metal flex hose attached (see burner
owner’s manual) set burner in base with burner
neck pointed toward the control panel.
2. Connect the incoming gas hose to the valve and
tighten securely. Repeat with flexible metal gas
line from the valve to the underside of burner.
It is not recommended to use Teflon tape or
pipe dope on the connection to the valve with
flare fittings.
LPG installations use the hose and regulator
provided with the burner.
For Natural Gas hookup information and any
other info not listed here consult your Crystal
Fire owner’s manual.
Attach incoming
gas here
Read and understand your Crystal Fire owner’s manual
before beginning burner hookups or using the device.

7 | P a g e
Igniter Installation
1. Make sure the valve is in the OFF
position
2. Unscrew sparker cap and hex nut (sparker
included with burner). Install as shown below.

8 | P a g e
3. To properly install ignition system, a spark and ground wire
need to be attached to the igniter box.
Your burner will arrive with three wires coming from
the underside of the burner assembly. The ORANGE
wire is used only for remote operated burner systems.
The remaining two wires can be plugged into the ports
on the back side of the sparker box in your control
panel.
Test system by depressing the button on the igniter. A
continuous repeating spark between the igniter
electrode and spark-receiving probe means everything
is connected properly. Consult the troubleshooting
section of your crystal fire owner’s manual if spark is
weak, intermittent, or not present.
4. Once ignition system is grounded and gas
connections are secured and checked for
leaks, set the burner back into its original
position if it was removed during gas hookup.
Burner

9 | P a g e
Locating your Tank
1. Your tank should be positioned so that
the fuel can be shut off after each use.
2. Slide the tank into the framework past
the line shown below (table style may
vary). This is to allow the door to close
completely.
3. Confirm all hoses are clear and not
touching the burner.
Position tank behind this line

10 | P a g e
Door Installation
Finishing touches
Once fire pit is set up and in the desired position,
scatter decorative glass on burner surface forming
an even layer of beads.
DO NOT BURN WITHOUT GLASS OR OTHER
DECORATIVE SUBSTRATE PRESENT
Set door on supports and close.
Magnet will hold door in closed position.
Door support
*Exact model may differ

11 | P a g e
Warranty: Fire pit tables are covered under a 1-
year manufacturer’s warranty. Please visit
http://www.outdoorrooms.com/warranty-form
to register your product.
IMPORTANT
Please consult your Crystal Fire instruction manual for detailed
instructions and important information related to hooking up your
linear burner, including safety information, proper tightening of
connections with two wrenches and full burner setup and lighting
instructions.
DO NOT ATTEMPT TO INSTALL BURNER WITHOUT FIRST
CONSULTING THE USER MANUAL. IF YOU ARE UNSURE OF HOW TO
COMPLETE THE STEPS OUTLINED, CONSULT A QUALIFIED
TECHNICIAN
WARNING
After consulting the manual and following instructions, remember; before operating,
all gas connections must be fully checked for leaks

12 | P a g e
© 2012 The Outdoor GreatRoom Company
2015 Silver Bell Road •Suite 195 •Eagan, MN 55122
Toll Free: 1-866-303-4028 •[e-mail]