Outdoor GreatRoom Company PR-1242-K User manual

Pine Ridge Fire Pit Table
Installation Instructions for Pine Ridge fire pit
models PR-1242-K and PR-2424-K

Contents
Required Tools…………………………….…..2
Placing and assembling the Table.………3
Gas Connection………………………….…….4
Igniter Installation…………….……………...6
Locating Propane tank………………………7
Finishing Touches……………………………7
Required Tools
Utility Knife
To cut and remove packaging
2 Open Ended Wrenches
To secure gas connections
Leather Gloves
To protect hands from rough edges
found on coffee table during
installation.
One AAA battery (not Included)
Required for electric spark igniter
installation
Two people are required for this
installation
90250 Rev B 8/2/16

Assembly Instructions
1. Open packaging and remove the access door
before removing the fire pit base from the box.
2. Set the base in the desired location and set concrete
top onto base Replace access door.
2
1

Gas Connections
1. Reach inside the burner cut-out and attach natural gas supply
line using a 3/8” flare fitting, or attach the included black
rubber propane hose and regulator to the bottom fitting of the
control valve.
TIGHTEN SECURELY WITH A WRENCH
2. Lay the burner upside down on a flat, soft surface to avoid
scratching the polished metal. Ensure the correct orifice is
installed for the fuel type you are using (see Crystal Fire user
manual included with burner for orifice sizing information)
Attach the included metal flex hose to the burner.
TIGHTEN SECURELY WITH TWO WRENCHES
3
Read and understand your Crystal Fire owner’s manual before
beginning burner hookups or using the device.
Do not use Teflon tape or pipe dope on flare fittings.
Propane input
Natural gas input
or
Natural gas supply line
as specified by local
building codes

3. Set the burner into the fire pit exactly as shown and
make final gas connection to the control panel.
Igniter
Igniter
Access Door
Access Door
Metal flex line to
burner
ONLY
TIGHTEN CONNECTION
SECURELY WITH WRENCH

Igniter Installation
1. Make sure the valve is in the OFF
position before beginning.
2. Install sparker as shown, using an
AAA battery (not included).
3.
Sparker will not operate correctly without an ignition and ground
wire attached.
Plug both BLACK wires hanging from the burner into
the back of the sparker box. If an orange wire is
present, do not use it. Orange wire is for automatic
ignition system add-on only.
Test system by pushing the button on the igniter.
Consult the troubleshooting section if spark is weak,
intermittent, or not present.

After installing igniter and making gas connections, verify that
they are tight and that no leaks are present using a solution of
soapy water or a commercially available leak-check solution.
Position Your Tank
(if applicable)
1. Remove door, connect the propane hose/regulator to the
propane tank and hand-tighten (DO NOT USE A WRENCH) and
slide the propane tank past the dotted line to ensure the door
closes properly. This process is the same for both rectangular and
square Pine Ridge models.
2. With tank inside base, ensure that no hoses, wires, or anything
else is kinked or touching the burner pan.
Finishing Touches
Scatter the included glass beads evenly on to
burner surface using all of the beads that came
with your fire pit.
DO NOT BURN WITHOUT GLASS OR OTHER
DECORATIVE MEDIA PRESENT

IMPORTANT
Please consult your Crystal Fire instruction manual for detailed
instructions and important information related to hooking up your
linear burner, including safety information, proper tightening of
connections with two wrenches and full burner setup and lighting
instructions.
DO NOT ATTEMPT TO INSTALL CF-1242 or CF-2424 BURNER
WITHOUT FIRST CONSULTING THE CRYSTAL FIRE OWNER’S MANUAL.
WARNING
After consulting the manual and following instructions, remember; before
operating, all gas connections must be fully checked for leaks
Warranty: Fire pit tables are covered under a 1-
year manufacturer’s warranty. Please visit
http://www.outdoorrooms.com/warranty-form
to register your product.
14400 Southcross Drive West •Suite 100 •Burnsville, MN 55306
Toll Free: 1-866-303-4028 •[e-mail]