Outdoor GreatRoom Company Stonefire SF-32-K User manual

1
/
Stonefire Fire Pit Table
Installation Instructions for SF-32-K

2

3
IMPORTANT
Please consult your Crystal Fire instruction manual for detailed
instructions and important information related to the burner
installation including: lighting and operating instructions, safety
information, and proper tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE BURNER WITHOUT
FIRST CONSULTING THE CRYSTAL FIRE OWNER’S MANUAL.
Contents
Required Tools………………………………….........3
Included with your Fire Pit………………………..4
Assembly Instructions……………………………….5
Gas Connections……………………………………….7
Igniter Installation…………………………………….9
Glass Installation………………………………………10
Position Your Tank…………………………………..11
42458 REV C 08.20.18
Required Tools
Utility Knife
To cut and remove packaging
2 Open Ended Wrenches
To secure gas connections
Leather Gloves
To protect hands from glass and sharp edges during install
One AAA Battery (not included)
Required for electric spark igniter installation
Phillips Screwdriver
To attach mounting screws to control panel
Two people are required for this
installation

4
Included with your Fire Pit
[X1]
[X4]
M6X20
Bolt A [X4]
Gas Valve Kit
Gas Valve [X1]
Mounting
screws [X2]
Control knob
[X1]
[X4]
Clear Silicone Pads
Top [X1]
Glass Cover [X1]
Base [X1]
Bolt Cap
M6 Allen Wrench

5
Included with your Fire Pit
A. 4 Fasteners
B. 4 B-Bolts
C. 4 C-Bolts
D. 4 Bolt Caps
E. Touch-Up Paint Bottle
Assembly Instructions
55
1. Unpack contents from box, and remove individual packaging from each
piece.
2. Lay Side Panel with Control Panel on soft, flat surface.
3. Position Support Piece on the Side Panel. NOTE: It is very important to
positon the Support Piece as shown in the picture below, to ensure that
your burner and propane tank fit correctly with your fire pit table base.
Assembly Instructions
1. Unpack all the contents from the box and remove the individual
packaging from each component.
2. Carefully lay the Top, with underside facing upwards, on a soft and flat
surface.
3. Using the M6 Allen Wrench, attach Bolt A (x4) to securely fasten the Top
to the Base.
4. Do a final tightening on the bolts you have installed in your fire pit.
Then, with the help of another person, turn the table right side up.

6
5. Hold the Gas Valve in place from behind the control panel as shown
while inserting the two included Mounting Screws. Use a Phillips
screwdriver to fasten.
6. Attach Control Knob by pressing on to the valve stem.
Insert screws
included with
Gas Valve Kit

7
1. Reach inside the burner cut-out and attach natural gas supply
line using a 3/8” flare fitting, or attach the included black
rubber propane hose and regulator to the bottom fitting of the
control valve.
TIGHTEN SECURELY WITH A WRENCH
2. Lay the burner upside down on a flat, soft surface to avoid
scratching the polished metal. Ensure the correct orifice is
installed for the fuel type you are using (see Crystal Fire user
manual included with burner for orifice sizing information).
Attach the included metal flex hose to the burner.
TIGHTEN SECURELY WITH TWO WRENCHES
Gas Connections
Read and understand your Crystal Fire owner’s manual before
beginning burner hookups or using the device.
Do not use Teflon tape or pipe dope on flare fittings.
Propane
input
Natural
gas input
or
Natural gas supply line
as specified by local
building codes

8
3. Set Burner into the fire pit base as shown below.
Metal flex line to
burner
ONLY
TIGHTEN CONNECTION
SECURELY WITH WRENCH
4. Attach flex line from the burner to gas valve as
shown below.
Igniter
Access Door

9
Sparker will not operate correctly without an ignition and ground wire
attached.
Plug both BLACK wires hanging from the burner into the back of
the sparker box.
Test system by pushing the button on the igniter. Consult the
troubleshooting section of the Crystal Fire Owner’s Manual, if
the spark is weak, intermittent, or not present.
Igniter Installation
1. Make sure the valve is in the OFF
position before beginning.
2. Install sparker as shown, using a
AAA battery (not included).
Negative end should be placed
inside the CF-SPARKER, positive
end outside of the CF-SPARKER.
OFF
OFF

10
Glass Installation
1. Scatter all of the included Glass Beads evenly onto burner surface.
DO NOT OPERATE CRYSTAL FIRE BURNER WITHOUT GLASS BEADS
OR OTHER DECORATIVE MEDIA PRESENT
2. Attach the Clear Silicone Pads (x4) to the bottom of your Glass
Cover. Space the pads evenly apart on the outer most edge of the
cover.
3. Place the Glass Cover on top of the burner, with silicone pads
facing downwards.
DO NOT OPERATE CRYSTAL FIRE BURNER WITH GLASS COVER IN PLACE