Outdoor GreatRoom Company Colonial-48-M-K User manual

1 | P a g e
Colonial and Grand Colonial Fire Pit Tables
Installation Instructions for
Colonial-48-M-K, Col-48-MNB-K, Grand-Colonial-48-K, CM-48-DIN-K, MNB-48-
DIN-K, GC-48-DIN-K, CM-48-PUB-K, MNB-48-PUB-K, GC-48-PUB-K
Chat/Dining/Pub Height Colonial Tables

2 | P a g e
Contents
Included Components……………..………………..………3-6
Assembly Iinstructions…………………………………….7-13
Gas Connections…………………………………………..…….14
Installing Igniter………………………….…………………15-16
Placing propane tank and finishing touches……..17
Required Tools
Utility Knife
To cut and remove packaging
2 Open Ended Wrenches
To make gas connections
Leather Gloves
To protect hands from rough edges found on the
coffee table.
One (1) AAA Battery (not included)
Required for piezoelectric igniter installation.
Electric screw gun with Phillips bit
(Granite tops only)
90220:D 7.10.2014

3 | P a g e
Tabletop frame Base with door Granite Pieces (x4)
Top-Securing Bracket
(x4)
#8-1/2” washer head screw (x4)
Lazy Susan/Burner Cover
Depending on which model you purchased, turn to the
corresponding page in this manual for installation instructions.
Base with door Supercast Tabletop with center
burner cover
(Instructions begin on page 7)
(Instructions begin on page 9)
Included with Chat-Height Grand Colonial
(Model: Grand-Colonial-48-K)
Included with Chat Height Colonial with Supercast Top
(Model: Colonial-48-M-K, Col-48-MNB-K)

4 | P a g e
Included with Dining Height Grand Colonial
(Model: GC-48-DIN-K) (flip to page 11 for assembly instructions)
Lazy Susan/Burner Cover
Dining-height base
with door
Tabletop Frame
Granite Pieces (x4)
Base Anchor
Note: A hardware pack is included with the aluminum tabletop
frame. The parts listed below will be taken from that hardware kit.
Other parts included in this kit can be discarded after installation is
complete.
Top mounting Bracket
Hex Key
M6 x 16 hex key screws (qty. 8)
#8-1/2” washer head
screw (x8)
(qty. 8)

5 | P a g e
Included with Dining Height Colonial with Supercast Top
(Model: CM-48-DIN-K, MNB-48-DIN-K)(flip to page 10 for assembly instructions)
Dining-height base
with door
Base Anchor
Supercast Tabletop with center burner cover
Included with Pub Height Colonial with Supercast Top
(Model: CM-48-PUB-K, MNB-48-PUB-K)(flip to page 10 for assembly instructions)
Dining-height base
with door
Base Anchor
Supercast Tabletop with center burner cover

6 | P a g e
Included with Pub Height Grand Colonial
(Model: GC-48-PUB-K) (flip to page 11 for assembly instructions)
Lazy Susan/Burner Cover
Pub-height base
with door
Base Anchor
Note: A hardware pack is included with the aluminum tabletop
frame. The parts listed below will be taken from that hardware kit.
Other parts included in this kit can be discarded after installation is
complete.
Top mounting Bracket
Hex Key
M6 x 16 hex key screws (qty. 8)
#8-1/2” washer head
screw (x8)
Tabletop Frame
Granite Pieces (x4)

7 | P a g e
Assembling the Grand Colonial
1. Remove all components from packaging and
inspect for damage or missing parts.
2. Move the base to desired location and set into
place before installing granite.
- When locating your coffee table, refer to the
Crystal Fire manual and maintain clearance to
combustibles.
3. Place top on base
as shown.
4. Line top up with base as shown.
Holes in tabletop frame are also used
for an alternate installation so not
every hole will line up directly
centered in each corner
of the base. This is
normal, as only 4 of
these holes are used in
this installation. A solid
line in the diagram at
right indicates the
approximate location
of the holes used for
mounting. Dashed lines
are unused holes.
Dashed lines: Holes not used
for this installation
Instructions For Model Grand-Colonial-48-K ONLY

8 | P a g e
6. With top securely
fastened to base, set granite
sections into place, polished
side up.
4. With top centered on
base and one hole
approximately centered on
each corner of the base,
insert a mounting clip into
mounting hole
(refer to image at right.)
5. Insert one of the
included screws through the
hole in the mounting clip
and screw into the table
base. Do not over-tighten as
this may cause stripping.
If stripping occurs, rotate
the top approximately 1”
and re-insert all screws.
Unused screw
hole
7. Gently lower your crystal fire burner into the burner
cutout and continue to the page 14 for gas hookup and
igniter hookup instructions.

9 | P a g e
Colonial Table Setup
1. Remove all components from packaging and
inspect for damage or missing parts.
2. Place the fiberglass table base in your desired
location on flat, level ground.
3. Line up top as shown to ensure foam pads
contact the underside of the top.
4. With help from another person, gently set concrete
top onto the base and center it. If the top doesn’t sit flat,
ensure that it is lined up correctly. For a more permanent
installation, an outdoor-rated construction adhesive or
silicone can be used to attach the top to the base.
5. Gently lower your crystal fire burner into the burner
cutout and continue to the page 14 for gas hookup and
igniter hookup instructions.
Instructions For Model Colonial-48-M-K and COLONIAL -48-MNB-K ONLY

10 | P a g e
Dining and Pub-height Colonial Table Setup
1. Remove all components from packaging and
inspect for damage or missing parts.
2. Place the fiberglass table base in your desired
location on flat, level ground.
3. Line up top as shown to ensure foam pads
contact the underside of the top.
4. With help from another person, gently set concrete
top onto the base and center it. If the top doesn’t sit flat,
ensure that it is lined up correctly. For a more permanent
installation, an outdoor-rated construction adhesive or
silicone can be used to attach the top to the base.
5. Gently lower your crystal fire burner into the burner
cutout and continue to the page 14 for gas hookup and
igniter hookup instructions.
6. Refer to page 13 for anchoring instructions.
*Dining-height base shown.
Installation is the same for
dining and pub-height models
Instructions For Models CM-48-DIN-K, MNB-48-DIN-K, CM-48-PUB-K,
MNB-48-PUB-K ONLY

11 | P a g e
Dining and Pub-height Grand
Colonial Table Setup
1. Remove all components from packaging and
inspect for damage or missing parts.
2. Place the fiberglass table base in your desired
location on flat, level ground.
3. See page 13 for important anchoring
instructions.
4. Set the aluminum top into place as shown (do
not let metal rest on foam pads)
5. Set metal brackets into place and line up with
the hole locations around the aluminum frame.
.
*Dining-height base shown.
Installation is the same for
dining and pub-height models
INSTRUCTIONS FOR MODELS GC-48-DIN-K, GC-48-PUB-K ONLY

12 | P a g e
6. Insert M6x16 hex key screws as shown and
tighten with the included Hex key.
7. Repeat for remaining sides
8. Using the included #8-1/2” Washer head screws, secure
mounting brackets to base. Use extreme caution not to
over-tighten the screws in order to keep them from
stripping.

13 | P a g e
9. Insert granite panels into the frame, polished side up as
shown.
10.
11. Gently lower your crystal fire burner into the burner cutout
and continue to page 14 for gas hookup and igniter hookup
instructions
Anchoring Instructions for Dining and Pub-Height Colonials
Pub-height Colonial models must be anchored to the surface
they are located on in commercial or other environments
where tipping risk is present. Anchoring of dining-height
colonials is optional but recommended.
With base in its final position, set the included metal anchoring
bracket into place as shown and secure to the mounting surface
with appropriate hardware (not included) for the surface being
mounted to.(concrete anchors, wood deck screws, etc. ) If the
holes in the bracket are too large, washers should be used to
ensure screw or bolt heads do not slip through.

14 | P a g e
Gas Connection
1. With proper orifice installed for the
application (#43 for propane, #31 for
natural gas) and metal flex hose attached,
set burner in base.
2. Connect the incoming gas hose (black
rubber hose from propane tank or incoming
natural gas line) to the valve and tighten
securely with two wrenches. Repeat with
flexible metal gas line from the valve to the
underside of burner. It is not recommended
to use Teflon tape or pipe dope on the
connection to the valve with flare fittings.
LPG installations use the hose and regulator
provided with the burner.
For Natural Gas hookup information and
any other info not listed here consult your
Crystal Fire owner’s manual.
Read and understand your Crystal Fire burner owner’s manual
before beginning burner hookups or using the device.
Metal flex hose to burner
Incoming LP or Natural Gas

15 | P a g e
Igniter Installation
1. Make sure the valve is in the OFF
position
2. Unscrew sparker cap and hex nut (sparker
included with burner). Install as shown below.
Wall of base
*Gas valve can be
turned to adjust
flame height

16 | P a g e
3. To properly install ignition system, an Ignition and Ground
wire need to be attached to the igniter box.
Start by plugging the black Ignition wire hanging from
the burner in to one port on the back of the igniter
(either side is fine).
Next; plug the Ground wire into the open port on the
igniter box.
Test system by depressing the button on the igniter. A
continuous repeating spark at the igniter on the burner
means everything is connected properly. Consult the
troubleshooting section of your crystal fire owner’s
manual if spark is weak, intermittent, or not present.
4. Once ignition system is grounded and gas
connections are secured and checked for
leaks, set the burner back into its original
position if it was removed during gas hookup.

17 | P a g e
Locating your Tank
1. Your tank should be positioned so that
the fuel can be shut off after each use.
2. Set tank inside base with adequate
clearance to burner so the two are not
touching.
3. Confirm all hoses are clear and not
touching the burner.
Finishing touches
Once fire pit is set up and in the desired position,
scatter decorative glass on burner surface forming
an even layer of beads.
DO NOT BURN WITHOUT GLASS OR OTHER
DECORATIVE HEAT-SAFE MEDIA PRESENT

18 | P a g e
Warranty: Fire pit tables are covered under a 1-
year manufacturer’s warranty. Please visit
http://www.outdoorrooms.com/warranty-form
to register your product.
IMPORTANT
Please consult your Crystal Fire instruction manual for detailed
instructions and important information related to hooking up your
linear burner, including safety information, proper tightening of
connections with two wrenches and full burner setup and lighting
instructions.
DO NOT ATTEMPT TO INSTALL CF-20 BURNER WITHOUT FIRST
CONSULTING THE MANUAL. IF YOU ARE UNSURE OF HOW TO
COMPLETE THE STEPS OUTLINED, CONSULT A QUALIFIED
TECHNICIAN
WARNING
After consulting the manual and following instructions, remember; before operating,
all gas connections must be fully checked for leaks

19 | P a g e

20 | P a g e
© 2014 The Outdoor GreatRoom Company