Outdoor GreatRoom Company Sierra User manual

1 | P a g e
Fire Pit Tables
Sierra and Grandstone
Installation Instructions

2 | P a g e
Contents
Contents……………………………………..2
Required Tools….………………………..3
Placing the Table…………………..……4
Igniter Installation ……………….…….5
Gas Connection…………….….………...6
Thermocouple Installation…….…...7
Electrode Installation………………….7
Placing the Top…………………………..8
Locating Propane tank………..……...8
Door Installation………………………...9
Notice:
This unit is listed for use in North America for both residential and commercial
applications. In the event that the appliance can be used by those unfamiliar with
the appliance, we suggest the use of a master Key Valve to prevent unauthorized
use. The use of a Glass Guard is also strongly recommended when small children
or other individuals with reduced sensory or mental capacities may be in close
proximity to the appliance.
42430:I 12.02.19

3 | P a g e
Required Tools
Utility Knife
To cut and remove packaging
2 Open Ended Wrenches
To make gas connections
Leather Gloves
To protect hands from rough edges
found on the coffee table.
One (1) AAA Battery (not
included)
Required for igniter installation for
Crystal Fire Plus burners.
It is recommended that a
minimum of two people
assemble and install fire
pit tables.

4 | P a g e
Placing the Fire Pit table
1. Remove access door
2. Remove the base from the box
3. Move the base without door to desired
location and set into place.
4. When locating your coffee table, refer to the
Crystal Fire Plus manual and maintain clearance
to combustibles.
Before completing the following steps, read and
understand the Crystal Fire Plus owner’s manual.
Sierra fire pit table shown,
finishes and styles may vary

5 | P a g e
Igniter Installation
Locate CF-SPARKER inside of crystal fire burner
box.
Remove CF-SPARKER cap and hex nut. Insert
AAA battery (not included) with + end out.
Install CF-SPARKER into control panel as shown
below.
Depress CF-SPARKER button to test your
sparker.
Locate and orient
sparker box on
control panel as
shown. Sparker box
must be installed
before burner valve.

6 | P a g e
Gas Connection
See Crystal Fire Plus instructions for burner
installation.
All gas connections were completed
at the factory.
Check all connections for leaks. If needed,
tighten connection with 2 wrenches and
re-check for leaks.
Attach burner valve to control panel with
provided screws as shown below. Ensure
sparker box is installed before this step.

7 | P a g e
Thermocouple Installation
•Refer to Crystal Fire Plus instruction
manual for detailed attachment of
thermocouple.
•Attach thermocouple to burner valve as
shown below.
Electrode Installation
• Plug both BLACK wires hanging from the burner into
the back of the CF-SPARKER. If an orange wire is
present, do not use it. The orange wire is for Direct
Spark Ignition system only.
• Test system by pushing the button on the igniter.
Consult the troubleshooting section of the Crystal Fire
Plus Burner Owner’s Manual, if the spark is weak,
intermittent, or not present.

8 | P a g e
Placing the top
1. With the help of at least one other person, remove
concrete, granite, or tile top from packaging and gently
lower on to your fire pit table base. Construction adhesive
or silicone may be used on the top of the base for a more
stable and permanent placement in heavy use areas.
Locating your Tank
1.Your tank should be positioned so that the fuel can be
shut off after each use.
2.Slide the tank into the framework past the line shown
below. This is to allow the door to close completely.
3.Confirm all hoses are clear and not touching the burner.
Position tank
behind this line
Lower burner onto base with burner neck facing in the direction of control
panel location.

9 | P a g e
Door Installation
Set door on supports and close. Magnet
will hold door in closed position.
Door support
IMPORTANT
Please consult your Crystal Fire Plus instruction manual for detailed
instructions and important information related to hooking up your
burner, including safety information, proper tightening of connections
with two wrenches and full burner setup and lighting instructions.
DO NOT ATTEMPT TO INSTALL BURNER WITHOUT FIRST
CONSULTING THE MANUAL. IF YOU ARE UNSURE OF HOW TO
COMPLETE THE STEPS OUTLINED, CONSULT A QUALIFIED
TECHNICIAN
WARNING
After consulting the manual and following instructions, remember; before operating,
all gas connections must be fully checked for leaks

10 | P a g e
ENTIONALLY LEFT
AWESOME.
14400 Southcross Drive West •Suite 100 •Burnsville, MN 55306
Toll Free: 1-866-303-4028 •[e-mail]
Warranty: Fire pit tables are covered under a 1-
year manufacturer’s warranty. Please visit
http://www.outdoorrooms.com/warranty-form
to register your product.