Outdoor GreatRoom Company Vaughn VGHN-GR-K User manual

Installation Instructions for Vaughn Fire Table
VGHN-GR-K and VGHN-WT-K
Vaughn Fire Table
outdoorrooms.com

IMPORTANT
Please consult your Crystal Fire® Plus instruction manual for detailed
instructions and important information related to the burner
installation including: lighting and operating instructions, safety
information, and proper tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE®PLUS BURNER
WITHOUT CONSULTING THE CRYSTAL FIRE®PLUS
OWNER’S MANUAL.
CONTENTS
1. About Your Fire Table 3
a. Required Tools
outdoorrooms.com42529 REV A 03-28-22
!!
2
b. Included With Your Fire Pit
2. Assembly Instructions
a. Unpacking
b. CF-SPARKER Installation
c. Tabletop Assembly
3. Setting Up Your Burner
a. Gas Control Installation
b. Thermocouple Installation
c. Electrode Installation
d. Securing Burner
e. Propane Tank Installation
4. Miscellaneous
b. Fire Media Installation
a. Tabletop Insert Installation
c. Burner Cover Installation
5. Operating Instructions
6. Warnings
4
6
10
12
13

outdoorrooms.com 3
Refer to Crystal Fire®Plus manual for items included with Crystal Fire®Plus burners
• Utility Knife
To cut and remove packaging
• Two (2X) Adjustable Ended Wrenches
To secure gas connections
•Phillips Screw Driver (Do not use a drill to assemble)
For assembly of table components
•10mm wrench
To secure thermocouple to gas valve
• One (1X) AAA Battery (Not Included)
Required for electric spark igniter installation
A. REQUIRED TOOLS
B. INCLUDED WITH YOUR FIRE PIT
1.
(1X) Base Assembly
(70134)
(1X) Table Top
(70131) (1X) Table Top Insert
(50032-GR or 50032-WT)
(1X) Access Door
(10489)
(1X) Burner Cover
(70032)
(4X) 1/4”-20 X 3/4”
Phillips Machine Screws
(1X) BI16 Burner Assembly
ABOUT YOUR FIRE TABLE
(4X) #8-32 X 3/8”
Phillips Machine Screws
(4X) #8-32
Hex Flange Nuts

outdoorrooms.com 4
ASSEMBLY INSTRUCTIONS
A. UNPACKING
• Do not discard any packaging until assembly is complete and unit is tested.
Keep all included manuals in a safe place for future reference.
• Access door and burner are packaged inside of the base in individual boxes.
• Keep the tabletop insert in the box on a at surface to prevent damage
during assembly process.
• Keep all BI16 burner components together during the assembly process.
WARNING
Exposed edges may be sharp, use leather gloves
when removing packaging and handling the base.
Do not remove protective cardboard packaging
until you have placed the re pit in
its desired location.
B. CF-SPARKER INSTALLATION
2.
!!
1. Locate CF-SPARKER inside of Crystal Fire® Plus burner box.
2. Remove CF-SPARKER cap and hex nut. Insert AAA battery (not included)
with + end out.
3. Install CF-SPARKER into control panel as shown below.
4. Press in CF-SPARKER button to test your sparker. If CF-SPARKER is working
correctly, there will be both an audible and visible spark.
CF-SPARKER

C. TABLETOP ASSEMBLY
outdoorrooms.com 5
1. Remove burner cover from tabletop and set aside. Orient tabletop on base
as shown below. A threaded insert should be visible at all four (4) locations.
2. Secure tabletop to base using the supplied (4X) 1/4”-20 X 3/4” and a
Phillips screwdriver.
DOOR SIDE
BACK OF BASE

outdoorrooms.com 6
SETTING UP YOUR BURNER3.
ATTENTION
Read and understand your Crystal Fire® Plus owner’s manual before
beginning burner hookups or using the device.
DO NOT USE TEFLON TAPE OR PIPE DOPE ON FLARE FITTINGS.
ALL GAS CONNECTIONS WERE COMPLETED AT THE FACTORY. SEE
CRYSTAL FIRE®PLUS INSTRUCTIONS FOR COMPLETE INSTALLATION
INSTRUCTIONS.
!
!
IMPORTANT
Please consult your Crystal Fire® Plus instruction manual for detailed
instructions and important information related to the burner installation
including: lighting and operating instructions, safety information, and proper
tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE®PLUS BURNER WITHOUT
FIRST CONSULTING THE CRYSTAL FIRE®PLUS OWNER’S MANUAL.
!!
A. GAS CONTROL INSTALLATION
1. Set burner assembly on table to allow easier access inside the base. During
this step, use top packaging material to prevent scratches on tabletop
from burner assembly. Attach burner control valve to base control panel
with included fasteners as shown below.

outdoorrooms.com 7
B. THERMOCOUPLE INSTALLATION
2. Press control knob onto burner control valve. It is keyed and will only
go on one way.
SEE DETAIL B
SEE DETAIL A
SCALE 0.800
DETAIL A
SCALE 0.800
DETAIL B
1. Carefully uncoil thermocouple from burner.
2. Connect thermocouple to control valve and tighten using 10mm wrench
or small adjustable wrench. Tighten until one (1) thread is visible.
See image below.
Refer to Crystal Fire®Plus instruction manual for more detailed information
regarding the installation of the thermocouple.
SEE DETAIL B
SEE DETAIL A
SCALE 0.800
DETAIL A
SCALE 0.800
DETAIL B

outdoorrooms.com 8
D. SECURING BURNER
1. Carefully uncoil orange igniter wire and black ground wire from burner.
2. Connect the two (2) wires to sparker box as shown in image below. It does
not matter which wire connects to which terminal; the sparker will work in
either conguration.
3. Test the ignition system by pressing the button on the sparker. Consult the
troubleshooting section of the Crystal Fire® Plus instruction manual if the
spark at the location shown above is weak, intermittent, or not present.
1. Remove any packaging used to prevent scratching in step 3A. Orient burner
as shown in image below.
2. Secure burner to burner plate using (4X) #8-32 X 3/8” Phillips machine
screws and (4X) #8-32 ange nuts. Use Phillips screwdriver on screw
and hold the nut with ngers.
C. ELECTRODE INSTALLATION

outdoorrooms.com 9
1. Ensure control valve on re table is in the OFF position and propane
tank valve is fully closed. Hand-tighten regulator hose connector
to propane tank.
2. Place tank in tank tray.
3. Secure access door to base.
E. PROPANE TANK INSTALLATION
ATTENTION
HAND TIGHTEN, DO NOT USE A WRENCH FOR THIS CONNECTION.
!!
PROPANE REGULATOR
PROPANE TANK
TANK TRAY
ACCESS DOOR