Overland Storage NEO 200S User manual

10400371-001 03/2012 ©2012 Overland Storage, Inc. Page 1 of 3
*10400371001*
NEO®200s/400s
Add-on/Spare Tape Drive Instructions
This document describes the following procedures for a NEO
200s/400s library from Overland Storage:
•Adding another tape drive to a library.
•Removing and replacing an existing tape drive.
Tape drives are hot-swappable.
CAUTION: While working with the unit, observe standard
Electrostatic Discharge (ESD) precautions to prevent damage
to micro-circuitry or static-sensitive devices.
Register the Add-on Drives
NOTE: If you are only replacing an existing drive, skip to the next
section, “Prepare the Unit.”
When installing tape drives to your new library, you must
register them to activate their warranty. This is normally done
at the same time as you register your new library. Technical
and warranty support are not available until this is done:
1. Go to the Overland Storage website
(http://www.overlandstorage.com/).
2. Select Service & Support > My Products.
3. At the Site Login, enter your e-mail address and
password, and click GO.
4. Click the Manage Products button.
5. From the Product Selector drop-down list, select the unit
in which you are installing the extra drives.
6. Click Add a Component.
7. Enter the drive information.
8. For each additional drive, click Save & Add Another,
then repeat Step 7.
9. When ALL disk drives are registered, click Save & Exit.
IMPORTANT: Your warranty certificate will be emailed to you.
Follow the instructions included in the email to complete the
registration process.
SAS
FC
Enter
Enter

10400371-001 03/2012 ©2012 Overland Storage, Inc. Page 2 of 3
Add-on/Spare Tape Drive Instructions
Prepare the Unit
Verify Library Firmware
To make sure you have the latest library firmware to support
the new tape drives, compare the library version against the
versions posted at http://docs.overlandstorage.com/neo.
1. Log on to the Web User Interface.
2. Go to Monitor Library > Library Identity to verify that you
are running the latest version of library firmware.
3. If necessary, upgrade the firmware (Service Library >
Upgrade Firmware).
Remove Cover for Add-on Drive
NOTE: If removing and replacing an existing tape drive, skip to the
next step, “Prepare Old Drive.”
1. If adding an additional drive to a library, determine the
proper location.
•2U library – Use the top drive bay.
•4U library with no partitions – Use the first empty
drive bay above the current installed drives.
•4U library using or creating partitions – Refer to the
NEO 200s/400s User Guide.
2. Loosen the blue captive thumbscrews and remove the
cover plate from the drive bay to be used.
3. Continue with “Insert New Drive in Library” below.
Prepare Old Drive
1. If necessary, unload the tape cartridge from the drive
being removed.
•Operator Control Panel: Control > Move Cartridges
•Web User Interface: Manage Library > Move Media
2. Before removing the old drive, power it down so it can be
removed:
a. At the Operator Control Panel, press:
Service > Service > Drive Power.
b. Select the drive being removed.
c. Press OK.
The drive can now be removed.
Remove Old Drive
NOTE: Fibre Channel and SAS drive sleds are hot-swappable and
may be removed and installed while the library is still powered ON.
1. Remove the host interface cable ()from the old drive.
2. Loosen both blue captive thumbscrews ().
3. Pull straight back on the drive sled handle ()to remove
it from the library, supporting it with both hands.

10400371-001 03/2012 ©2012 Overland Storage, Inc. Page 3 of 3
http://support.overlandstorage.com
You can get additional technical support on the Internet at the Overland Storage Support web page, or by contacting Overland Storage using
the information found on the Contact Us page on our web site.
Add-on/Spare Tape Drive Instructions
Install the Drive
Insert New Drive in Library
1. If working with the bottom drive bay, extend the black
pull-out tab ()located underneath the library and
ensure the tab remains extended during installation.
2. While supporting the drive bottom, use the handle ()to
slowly insert the new drive sled into the drive bay until
the sled seats itself against the back of the library.
CAUTION: Damage to the connector pins may occur if this
procedure is not followed.
3. Tighten the thumbscrews ()to secure the drive.
4. Push the black tab back underneath the library.
5. Connect the host interface cable ()to the drive port
().
NOTE: For SAS drives, always use Port A.
Verify the New Drive
1. If it is an FC drive, from the Web User Interface use
Configure Library: Drives to configure the new FC drive.
2. From the Operator Control Panel, run the Library Verify
test. (Service > Library Verify).
The verify test requires the use of a scratch (blank)
cartridge. Insert it using the Mail Slot.
3. Do one of the following:
•If the test passes, remove the cartridge, press Cancel
to exit, and resume normal operations.
•If the test fails, contact Overland Technical Support.
Return Old Part to Overland
If replacing an existing drive, for return shipping details and
an RMA number, go to:
http://docs.overlandstorage.com/return-instructions
1. Place the old part in the anti-static bag and put it in the
replacement part’s box.
2. Use a return merchandise authorization (RMA) number to
return the part to Overland Storage.
*35P1406*
PN 35P1406
Printed in Mexico