Overland Storage NEO 8000 User manual

Part Number 10400014-101 04/2006 ©2006 Overland Storage, Inc. WPage 1 of 2
Introduction
IMPORTANT: Overland Storage requires that all NEO 8000
parts be removed and replaced by an Overland Storage
authorized service provider. Improper installation may
result in damage which voids existing warranties.
This document describes how to either remove and replace
or add a power supply module in a NEO 8000 Library from
Overland Storage.
Unpacking the Spare
Carefully unpack the spare part and verify that you have
all the parts:
•Power supply module
•These remove & replace/add-on instructions
WARNING: The GUI touch screen does not
completely shut off NEO 8000 system power. To
reduce the risk of electric shock or damage to
equipment, disconnect the power by unplugging
the power cords.
Electrostatic Discharge Information
A discharge of static electricity can damage micro-circuitry
or static-sensitive devices. To help prevent electrostatic
damage, observe the following precautions:
•Transport and store items in static-safe containers.
•Keep electrostatic-sensitive parts in their containers
until they arrive at static-free stations.
•Use a wrist strap and properly-grounded tools.
•Make sure you are always properly grounded when
touching a static-sensitive component or assembly.
•Keep the work area free of non-conductive materials.
•Avoid touching pins, leads, or circuitry.
A NEO 8000 power supply is designed as a single unit to
permit quick and easy installation or replacement.
1. At the front panel, power down the library.
2. Set the library circuit breakers to OFF (“O”), and
remove and retain the power cords.
3. If replacing an existing power supply, remove the old
module (Figure 1).
a. Completely loosen the captive fastener
thumbscrew in the lower left corner.
b. Pull the captive fastener all the way down.
c. Grab the handle and gently pull the power supply
module out.
There is some initial resistance as the module
releases from the backplane.
4. If adding a new power supply, remove the cover plate
by gently prying off it off. It is held in place by spring
latches. Figure 1. Power Supply Latch
NEO 8000 Library
Power Supply Module Spare
Remove & Replace/Add-On Instructions
Overview & Notes
NEO-8043
TM
Adding or Replacing a Power Supply
NEO-8043

Part Number 10400014-101 04/2006 ©2006 Overland Storage, Inc. WPage 2 of 2
5. Slide the new power supply module into the empty
slot, pushing slowly until it seats firmly against the
backplane of the power supply case.
6. Lift the captive fastener up fully and tighten the
thumbscrew.
NOTE: If the fastener doesn’t lift completely, press the
power supply inward to fully connect it with the backplane.
7. Be sure the power switch on the new power supply is
in the ON (“|”) position.
8. Reconnect the power cords and turn the circuit
breakers to the ON (“|”) position.
The green LED on the new power supply should come on
during POST. If it doesn’t light up, check that the power
supply module is completely inside the case and in full
contact with the backplane.
All information contained in or disclosed by this document is considered proprietary by Overland Storage. By accepting this material, the recipient agrees that this material and the information contained therein are
held in confidence and in trust and will not be used, reproduced in whole or in part, nor its contents revealed to others, except to meet the purpose for which it was delivered. It is understood that no right is conveyed
to reproduce or have reproduced any item herein disclosed without express permission from Overland Storage. Overland Storage provides this document as is, without warranty of any kind, either expressed or
implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Overland Storage may make improvements or changes in the product(s) or program(s) described
in this document at any time. These changes will be incorporated in new editions of this publication.
Overland Storage assumes no responsibility for the accuracy, completeness, sufficiency, or usefulness of this document, nor for any problem that might arise from the use of the information in this document.
Additional Help
You can get additional technical support on the Internet at support.overlandstorage.com,
or call 1-877-654-3429 (toll-free U.S. & Canada), [phone] (Europe), or
001-858-571-5555 x5 (International).