Overland Storage SnapServer XSD 40 User manual

10400569-001 ©2014 Overland Storage, Inc. Page 1 of 3
*10400569001*
SnapServer®XSD 40
Add-on/Spare Disk Drive Instructions
This document describes how to either add a new disk drive or
remove and replace an existing disk drive in a SnapServer
XSD 40 Desktop Storage Appliance from Overland Storage.
WARNING: To reduce the risk of electric shock or damage to
equipment, always remove any power cords while working
with the unit.
WARNUNG: Um das Risiko eines elektrischen Schlags oder
Schäden am Gerät zu vermeiden, ziehen Sie stets den
Netzstecker, bevor Sie an der Einheit arbeiten.
AVERTISSEMENT: Pour réduire le risque de choc électrique
ou endommagement de l'équipement, retirez toujours les
cordons électriques en travaillant avec l'appareil.
CAUTION: While working with the unit, observe standard
Electrostatic Discharge (ESD) precautions to prevent damage
to micro-circuitry or static-sensitive devices.
Register the Add-on Drives
When adding an additional drive to your server, you must first
register it to activate the warranty. Technical and warranty
support are not available until this is done:
1. Go to the Overland Storage website
http://www.overlandstorage.com/
2. Select
Service & Support > My Products .
3. At the Site Login, enter your e-mail address and
password, and click GO.
4. Click the Manage Products button.
5. From the Product Selector drop-down list, select the
XSD 40 in which you are installing the extra drive.
6. Click Add a Component.
7. Enter the drive information.
8. Click Save & Exit.
IMPORTANT: Your warranty certificate will be emailed to you.
Follow the instructions included in the email to complete the
registration process.
Enter
Enter
5325301507-XSD 40 s/n: 0247

10400569-001 ©2014 Overland Storage, Inc. Page 2 of 3
Add-on/Spare Disk Drive Instructions
Swap/Install Drives
Remove the Drives
Drives being replaced must be removed. Retain the drive to
return it to Overland Storage, Inc.
NOTE: Do not remove the disk drives from their carriers. Doing so
voids the drive warranty.
1. Slide the release button on the carrier to the right.
The latch on the front of the carrier will release and the
handle will extend.
2. Set the assembly on a secure surface.
3. Repeat Steps 1–2 for each remaining carrier.
Prepare New Drives
The handle mechanism must be unlatched to install the new
drive carriers in the XSD 40.
1. Slide the release button on the carrier to the right.
The latch on the front of the carrier will release and the
handle will extend.
2. Set the assembly on a secure surface.
3. Repeat Steps 1–2 for each remaining new drive carrier.
Install New Drives
1. With the door open, position a new drive assembly in
front of the topmost empty bay.
2. Slide the assembly into the bay until it stops.
3. Swing the handle closed until it clicks, locking the drive
into place.
4. Repeat Steps 1–3 for any other drives or blank drive
carriers being installed.
5. Close the door.
Pull Carrier
Slide Right
Slide In Carrier

10400569-001 ©2014 Overland Storage, Inc. Page 3 of 3
http://support.overlandstorage.com
You can get additional technical support on the Internet at the Overland Storage Support web page, or by contacting Overland Storage using
the information found on the Contact Us page on our web site.
Add-on/Spare Disk Drive Instructions
Attach Cables and Power Cord
1. Reattach all the cables (except the power cord) to the
same connections previously used.
2. Attach the power cord.
3. At the front, press the power button to power it ON.
IMPORTANT: If this is a new appliance install, continue with
the SnapServer XSD 40 Quick Start Guide instructions.
Return Old Parts to Overland
1. Place the old part in the anti-static bag and put it in the
replacement part’s box.
2. Use an RMA to return the part to Overland Storage.
For return shipping details and RMA number, go to:
http://docs.overlandstorage.com/return-instructions
Activate New Drives
For details on activating any new drives in a XSD 40, refer to
the SnapServer Administrator’s Guide For GuardianOS 7 on
replacing disk drives in the Disks and Units section.
That section covers both DynamicRAID and Traditional RAID
configurations.
AC Power
Cable Ports