Panasonic KX-TGP500 Instruction manual

Supported Devices-Panasonic
Panasonic KX-TGP500
How to Find the IP Address
How to Find the MAC Address
How to Set the Configuration Server
How to Restore to Factory Default
Panasonic KX-TGP550
How to Find the IP Address
How to Find the MAC Address
How to Set the Configuration Server
How to Restore to Factory Default
Panasonic KX-UT13X
How to Find the IP & MAC Addresses
How to Set the Configuration Server
How to Restore to Factory Default
Panasonic KX-UT670
How to Find the IP & MAC Addresses
How to Set the Configuration Server
How to Restore to Factory Default
Panasonic KX-TGP500

1.
2.
3.
4.
How to Find the IP Address
Press the “Menu” button on a handset (Center Joystick).
Press the following key presses on the keypad ([#][5][3][4]).
Select "On" for "Embedded web" [SAVE].
Now to view the IP Address press the “Menu” button on a handset (center of joystick).
How to Find the MAC Address

1.
2.
3.
First log into the Web Admin GUI of the phone. The password is "adminpass" by default.
Click on “Network Status” option on the left side.
The MAC address will be displayed like below.
How to Set the Configuration Server

1.
2.
3.
First log into the Web Admin GUI of the phone. The password is "adminpass" by default.
Next select the “Maintenance” tab at the top right.
Next select the “Provisioning Maintenance” tab.

4.
1.
2.
You can now specify the provisioning server information. In our example we are using tftp://10.10.0.1/Config{MAC}.cfg
How to Restore to Factory Default
First log into the Web Admin GUI of the phone. The password is "adminpass" by default.
Next select the “Maintenance” Tab at the top right.

3.
4.
Now use the left navigation menu to select “Reset To Defaults."
Finally click “Reset Web Settings” to complete the reset.
Panasonic KX-TGP550

How to Find the IP Address

1.
2.
3.
Press the “Menu” button.
Scroll to “IP Service” and press the “Select” button.
Scroll to “Network Setting” and press the “Select” button.

4.
5.
1.
Scroll to “IP Setting” and press the “Select” button.
The IP address will be displayed.
How to Find the MAC Address
Log into the Web Admin GUI of the phone. The password is "adminpass" by default.

2.
3.
1.
Click on “Network Status” option on the left side.
The MAC Address will be displayed like below.
How to Set the Configuration Server
Log into the Web Admin GUI of the phone. The password is "adminpass" by default.

2.
3.
4.
1.
Select the “Maintenance” tab at the top right.
Next select “Provisioning Maintenance."
You can now specify the provisioning server information. In our example we are using (Reference thetftp://10.10.0.1/Config{MAC}.cfg
screen above.)
How to Restore to Factory Default
Log into the Web Admin GUI of the phone. The password is "adminpass" by default.

2.
3.
4.
Next select the “Maintenance” tab at the top right.
Now select “Reset to Defaults” on the left navigation menu.
Finally click the “Reset Web Settings” button to complete the reset.
Panasonic KX-UT13X

1.
How to Find the IP & MAC Addresses
Press the “Setting” button.

2.
3.
1.
Select “Information Display."
Scroll down to see either the IP or MAC Address.
How to Set the Configuration Server
Log into the Web Admin GUI of the phone. The password is "adminpass" by default.

2.
3.
4.
1.
Select the “Maintenance” tab at the top right.
Next select “Provisioning Maintenance."
You can now specify the provisioning server information. In our example we are using (Reference thetftp://10.10.0.1/Config{MAC}.cfg
screen above.)
How to Restore to Factory Default
Log into the Web Admin GUI of the phone. The password is "adminpass" by default.

2.
3.
4.
Next select the “Maintenance” tab at the top right.
Now select “Reset to Defaults” on the left navigation menu.
Finally click the “Reset Web Settings” button to complete the reset.
Panasonic KX-UT670

1.
How to Find the IP & MAC Addresses
Press the “Menu” button.

2.
3.
Press the “Settings” button.
Scroll down and press the “About Phone” option.

4.
5.
Select the “Status” option.
The IP and MAC Addresses will display here.
How to Set the Configuration Server

1.
2.
3.
Log into the Web Admin GUI of the phone. The password is "adminpass" by default.
Select the “Maintenance” tab at the top right.
Next select “Provisioning Maintenance."