Panasonic ET-PFD560 User manual

INSTALLATION MANUAL
Projector Frame E T -PFD560
Only aqualified installer should install this pr oduc t .
Read these instructions carefully before installing the ET-PFD560 P r ojec t or F r ame .
These installation instructions must always be provided to the cust omer .
For use with Panasonic DLP® p r ojec t or models:
PT-RZ21KU, PT-RQ13KU, PT-RZ12KU, PT-RS11KU
PT -DZ21KU/K2U, PT -DS20KU/K2U, PT -DW17KU/K2U, PT-DW16KU/K2U
Important
safety notice 2
P roduc t description 3
Finished assembly diagram 3
Assembly procedure 4
Installing theprojector 4
Installing tandem projections 6
Adjustment options 6
Dimensions 7

IMPORTANT SAFETY NO TICE
Dear C ustomer ,
This instruction booklet provides you with the necessary operating informationthat you
requir e . It will help you to get the best performance out of this newproduc t . Wehope you
will be pleased with your Panasonic P r ojec t or F r ame .
Model number :
E T -PFD560
Precautions with regard to saf et y
WARNING
Installation work shouldonly be carried out by a qualified t echnician.
- If this product is not installed cor rec tly , seriousaccidents and injury may occur.
Donot place the projector or frame on top of unstablesurfaces.
- If the projector isplaced ontop of a surface which issloped or unstable , it may fall or tip over and
injury or damage could result.
Suspended installations should only be made by using specially designed
hanging accessories andunder the following c onditions:
- Maximum hanging 2 framed projectors when using the trussmount E T -PFD550TMS2
C A UTION
Donot install the projectorin a place which may impedeprojector v en tila tion.
- If this is not obser ved , fire may result.
Donot install the projector in humid or dusty places or in places where the projector may
come into c on tac t with oily smoke or steam.
- Usingthe projector under suchconditions may result in fir e , electric shocksor plastic or optical det er ioration.
Minimum 2people are required to install the frame.
-T he weight of one frame ET-PFD560 is 19kg ( 42 lb.) and one projector PT-RZ21KU is 50 kg (110 lb).
T otal is 69kg (152 lb.) For saf et y , atleast 2 people are required to perform any kind ofinstallation.
2.

PRODUCT DESCRIPTION
to theframe.
FINISHED ASSEMBLY DIAGRAM
Do not stack or hang three frames .
FINISHED TANDEM ASSEMBLY
Upper projector
Lower projector
3.
Parts name
Image/Drawing
Purpose
F r am e
Holds
projector forstackingandhanging .
Screws and
washers
Screws (M6x3) x6
Flat washers (M6) x12
S ecures the projector base to the
frame.
Safety cable
Provides backup support

ASSEMBLY PR OCEDURE
(2)Screwdriver
sizeand location of the screen as well as the lens (sold separately)
In case of tandem projection: Install the lower projector first,
(see adjustment option, page 5). In case of tandem projection,
INSTALLING THE PROJEC T OR
INSTALLATION PR OCEDURE
Place the frame on the projector and align the
screwhole positions .
(Make sure that the front/rear direction is c orr ec t
when installing . If the direction is r ev ersed , the
hole positions will not line up .)
S ecur e the projector to the frame using thesix
screws (M6x30) and the twelve flat washers. Glue
the washers to the frame base if desired (M6).
TighteningTorque: 4± 0.5Nm
flat washers (M6)
4.
Screw (M6x30)
1. Preparation.
Prepare the tools.
(1)Adjustable spanner or Allen key
(3)Soft cloth or othersoftfabric
Check the load capacity of the set-up loc a ti on .
2. Check theframe .
Check the structural components.
3.
D e t e r min e t h e set t i ng - uppo s i t i on .
Select thepositionforthe projectors based on the
to be used.
4. Install theprojector(s).
Please see below.
followedbytheupperprojector.
5.
Carry out adjustment s.
Adjust so that the image fits perfectly onthescreen
adjust until imagesprojected bythe upper and lowerprojectors
converge on the screen.

INSTALLING THE PROJEC T OR
INSTALLATION PR OCEDURE
Use the enclosed steel wire
to secure the projector totheframe
by drawing the wire around the
securing bar (1) of the projector as
shown in image 1.
1
Fix both end la t ches with theenclosed
car abiner . Please make sure that thesteel
wire clasps the securing bar of the
projector (1)and the steel bar of the frame
(2).The carabiner screwmust be tightly
fastened!
2
1
5.
1
2
1

INSTALLING TANDEM PROJEC TIONS
INSTALLATION PR OCEDURE
female bolt
locking pin
male bolt
Place the upper framedprojector on t op
of the lower framedprojector. Make sure the fourmale bolts
seat into the correspondent female
bolts . To secure, push the locking pin thr ough both
bolts , and confirm the snap.
ADJUSTMENT OPTIONS
Using theleftandright ratchets you can
adjust the projector tilt by approximately
five degr ees . You can lower or lift thewhole
front or the left orright c or nersalone .
ratchet
By turning theround knob onthe side ofthe
fr ame , you can rotate the back of thepr ojec t or ,
to theleft or right byapproximately five degr ees .
round button
6.

DIMENSIONS
720 mm / 28.35 I nches
419.95 mm / 16.53 I nches
690 mm / 27.17 I nches
7.
419.95
mm
/
16.53
I
nches
883
mm
/
34.76
I
nches
488
mm
/
19.21
I
nches