Pandora SMART PRO V3 User manual

Сертификат соответствия RU C-RU.MT49.B.00406/20
Pandora would like to thank you for
choosing our service-security system
Pandora Smart Pro v3 is a car service-security system built for cars with on-board voltage of 12V.
It is a complex engineering solution, which includes unique and modern technological software and
hardware solutions.
When building the Pandora Smart Pro v3 we were using the most up-to-date electronics from
world’s best manufacturers. The device is built using high-precision mounting and control machinery,
thus we guarantee highest possible quality, reliability and stable technical characteristics for the whole
operation period.
The Pandora Smart Pro v3 has a cryptographically strong authorization code with unique dialog
algorithm and individual encryption key on every device. It guarantees protection form electronic
hacking for the whole operation period.
The system is built for your convenience: it’s ergonomic, reliable, has the highest security and
service characteristics, 3 years unconditional warranty and free service and support. We are happy to
provide any support we can – feel free to use our online support.
!WARNING! It is strongly advised to have professional car mechanic installing the system.
Any car electronics installer should be able to install the system using installation scheme in this
manual and the special software. Most features are highly dependent on competent installation.
Our systems are thoroughly tested for quality, so if a feature fails to produce expected result,
most likely the problem is in improper installation.
This device has limited external factors resistance. It should not be subjected to water beyond occasional splatter, or operated in
temperatures outside -40 to +85° C range. All system components must be installed only in a car interior.
The base unit and radio tags fulfil with the IP40 category of protection against water.
Our web-site: pandorainfo.com
Customer support: [email protected]

2PA N D O R A S M A R T P R O V 3
Table of contents
General information 4
System set 4
Read before using 5
PIN codes of the system 6
Owner’s personal card 6
External VALET button 7
System modules layout 7
Base unit 8
Information signals of the system 10
System functions and modes 12
Security mode 12
Security and monitored zones 12
Remote and automatic engine starts 13
Slave mode 14
Owner authorization devices and functions 15
Checking the number of paired devices 16
Immobilizer radio tag 17
Functions of the button 17
Replacing an immobilizer tag battery 18
Updating firmware of the tag 19

3
U S E R MA N UA L
Control by a phone 20
Changing settings via a phone 23
Online service and mobile applications 25
Control the system 28
Arming 28
Disarming 29
Locking/unlocking doors when ignition is on 30
PANIC mode 31
Remote engine start 32
Service mode 33
Control the system in case of emergency 35
Emergency disarming 36
Emergency control of the anti-theft functions 36
Additional devices 38

4PA N D O R A S M A R T P R O V 3
System set
1. User manual 1.
2. Owner’s card 1.
3. Radio tag 2.
4. Case for radio tag 1.
5. External VALET button 1.
6. Beeper 1.
7. Base unit 1.
8. Blocking relay 1.
9. External temperature sensor 1.
10. Wires and fastening kit 1.
11. Piezo siren PS-330 1.
12. Wiring diagram 1.
13. Packaging 1.
! THE MANUFACTURER RESERVES THE RIGHT TO CHANGE THE SYSTEM SET AND CONSTRUCTION OF THE PRODUCT TO IMPROVE ITS
TECHNOLOGICAL AND OPERATIONAL PARAMETERS WITHOUT ANOTIFICATION.

5
U S E R MA N UA L
Read before using
Carefully read this manual before starting installation and using the security-service system. Pay
attention to text marked with !
!THE SECURITY AND TELEMETRIC SYSTEM IS ACOMPLEX TECHNICAL PRODUCT. SYSTEM INSTALLATION AND CONFIGURATION MUST BE
CARRIED OUT ONLY BY ASKILLED PROFESSIONAL.
!FEATURES AND SYSTEM MODES, CONTROL OF THE VEHICLES ZONES DEPENDS ON THE TYPE OF CONNECTION AND SYSTEM SETTINGS,
ORIGINAL VEHICLE OPERATION LOGIC AND TRIM.
! THE SYSTEM SET INCLUDES THE “OWNER’SPERSONAL CARD”. THIS CARD CONTAINS INFORMATION UNDER APROTECTIVE LAYER
THAT IS INTENDED ONLY FOR THE OWNER OF THE SYSTEM. MAKE SURE THAT THE PROTECTIVE LAYER ON THE OWNER’SPLASTIC CARD IS
INTACT AFTER THE INSTALLATION OF THE SYSTEM. READ THE “OWNER’SPERSONAL CARD” SECTION OF THIS MANUAL BEFORE ERASING
THE PROTECTIVE LAYER.
! WHEN SYSTEM INSTALLATION IS FINISHED:
• CheCk the system operation and funCtions with a speCialist.• we reCommend that you mark eaCh working funCtion with a sign IN THE “CONTROL THE SYSTEM” SECTION
• CheCk that the “installation CertifiCate” and “warranty Card” are filled out. these doCuments may be required for CONTACTING THE CUSTOMER SUPPORT.
• ask an installer to mark the layout of the system Components on the diagram. this information may be required for DIAGNOSTIC/CONFIGURING OR EMERGENCY DEACTIVATION OF THE SYSTEM.
WERECOMMEND THAT YOU CHANGE THE DEFAULT VALUE OF THE PIN-CODES OF THE SYSTEM. YOU CAN WRITE DOWN THE CHANGED
PIN-CODES IN THE “PIN-CODES OF THE SYSTEM” SECTION.

6PA N D O R A S M A R T P R O V 3
PIN-codes of the system
The “Secret PIN-code”
(is written on the “Owner’s personal card”
The “Service PIN-code”
(default value is 1-1-1-1)
The “Guest PIN-code”
(default value is 1-2-3-4)
The “Immobilizer PIN-code”
(is used for the Validator (pin-to-drive) function)
! ITIS RECOMMENDED THAT YOU WILL WRITE DOWN THE CHANGED OR CREATED VALUES OF ALL PIN-CODES. ELIMINATE THIRD-PARTY
ACCESS TO THIS INFORMATION
Owner’s personal card
! ERASE THE PROTECTIVE LAYER CAREFULLY. DONOT USE ANY SHARP OBJECTS TO AVOID DAMAGING OF HIDDEN INFORMATION UNDER
THE PROTECTIVE LAYER.
The owner’s personal card contains private information under a
protective layer:
•PIN (the “Secret PIN-code”) is a 4-digit number. This code can
be used to disarm the system and to deactivate immobilizer
functions and to activate service mode. It can be also used to
enter programming mode.
•LOGIN is a 10-digit number. This information is used to add
the system to the online service and mobile applications.
•PASS contains 8 characters and can consist of digits, lower and
upper case letters). This information is used to add the system
to the online service and mobile applications.
•Phone number is a phone number of the built-in SIM-chip.
CANNOT BE CHANGED
+7-9хх-ххх-хх-хх
1070000000 / Y34aC4vJ
2-2-2-2
LOGIN / PASS
PIN Phone number

7
U S E R MA N UA L
System modules layout
External VALET button
(VALET button via CAN)
Button
for the immobilizer PIN
Circuit being blocked
Base unit
Beeper
1
2
3
4
5
6
7
External VALET button
An external VALET button with a three-color status LED indicator is placed
inside a vehicle (see the system modules layout) The button is used for
programing the system, arming/disarming, activating/deactivating
immobilizer mode.

8PA N D O R A S M A R T P R O V 3
Base unit
Built-in GSM modem (2G/3G/4G LTE) provides a connection with our online-service pandora-on.
com and mobile applications (Pandora Online/Pandora Pro), allows to control the system by a phone
using DTMF-commands, voice and SMS notifications, automatic date and time detection. The modem
operates in a mobile network using the built-in SIM-chip or/and a nano-SIM.
Built-in SIM-chip (SIM1 of the system) is and integrated SIM-card chip that it used to work with the
built-in GSM modem. The built-in SIM-chip has a tariff plan for Russia (phone number is written on the
“Owner’s personal card”).
Built-in slot for a nano-SIM (SIM2 of the system) is used for owner’s SIM-card (nano-SIM) If both
the SIM-chip and SIM-card are used in the system, there is a function that allows to automatically switch
between the SIM-chip and the SIM-card if there is no internet connection
! it is required to install an additional sim-Card in the nano-sim slot for the automatiC mode. if you install a SIM-CARD IN THE NANO-SIM SLOT, SET UP THE SIM2 SETTINGS.
Built-in GPS/GLONASS-receiver is designed to determine current location and to automatically
determine UTS date and time.
2.4GHz radio channel, Bluetooth 5.0 protocol (BT5.0) supports up to 14 additional Bluetooth
devices (see the“Additional devices”section), including a mobile phone.
Built-in 3D accelerometer is used to detect shock/motion/tilt including 2 separate zones of shock
sensor (alarm and warning), the system allows to adjust sensitivity of each zone, to use data from the
accelerometer to block the engine and close the central lock on movement.
Temperature sensors allow the system to measure temperature of different zones to send this
information to the mobile apps.The following zones are available: interior temperature – built in sensor
of the main unit, engine temperature – external temperature sensor (see the “System set”), outside
temperature – digital car protocol*.
The system setting allow you to reassign sensor to different zones and use information from
external additional devices (PS-331BT, RHM-03 BT, DMS-100 BT); to implement automatic engine or
engine pre-heater starts and stops by temperature-

9
U S E R MA N UA L
Built-in digital 2хCAN* interface allows the system to read status end exucute commands via
digital buses.
Built-in digital IMMO-KEY port and immobilzer bypass* – hardware and software algortihms
with the special Pandora CLONE server allow the system to bypass original immobilizers for automatic
and remote engine starts.This port can be also used to control Webasto Thermo Top Evo и Eberspacher
Hydronic/2 heaters.
Built-in micro-USB port – update and configuration of the system using a PC and Pandora
AlarmStudio.
!*MORE INFORMATION IS AVAILABLE ON LOADER.PANDORAINFO.COM.

10 PA N D O R A S M A R T P R O V 3
Information signals of the system
LED INDICATOR SIGNALS
SIGNALS DESCRIPTION
THE SYSTEM IS ARMED
Short red ashes System is armed
Short green ashes System is armed
(an authorization device is in the coverage zone)
Fast red ashes Alarm
THE SYSTEM IS DISARMED
Faded System is disarmed
Red System is preparing for automatic or delayed arming
Green
(when ignition is on) System is in service mode
Green ashes
(when switching on ignition) Conrms the number of paired radio tags
Red ash
(when switching on ignition) Conrms a paired mobile device
WHEN ENTERING THE“SECRET PIN-CODE”OR THE“SERVICE PIN-CODE”
Orange ash Conrms a VALET button press
Short red ash Conrms a digit input PIN-code is incorrect
Red and green ashes Conrms correct PIN code