Pandora Camper Pro User manual

ENPandora would like to thank you for
choosing our security system Pandora Camper Pro
Pandora Camper Pro – is a telemetric service-security system built for motorhomes with on-board
voltage of 12V. It is a complex engineering solution, which includes unique and modern technological
software and hardware solutions.
When developing the system, we were using the most up-to-date electronics from world’s best
manufacturers. The device is built using high-precision mounting and control machinery, thus we
guarantee highest possible quality, reliability and stable technical characteristics for the whole
operation period.
Pandora has a cryptographically strong authorization code with unique dialog algorithm and
individual 128 bit encryption key on every device. We guarantee 100% protection form electronic
hacking for the whole operation period.
The system is built for your convenience: it’s ergonomic, reliable and it has the highest security and
service characteristics, 3 years unconditional warranty and free service and support. We are happy to
provide any support we can – feel free to use our online support.
This device has limited external factors resistance. It should not be subjected to water beyond occasional splatter, or operated in
temperatures outside -40 to +85° C range. All system components must be installed only in a car interior. The base unit, remote control and
radio tags fulfil the IP40 category of protection against water.
Our web-site: pandorainfo.com
Customer support: [email protected]

2SECURITY-SERVICE SYSTEM PANDORA CAMPER PRO
Table of contents
1. General information 4
System set 5
System modules layout 7
Base unit of the system 8
Owner’s personal card 10
External VALET button 10
2. System functions and modes 12
Security mode 13
Security zones 13
Sound and light signalization 14
Stay Home mode 15
Slave mode 15
Owner authorization devices and functions 15
Checking the number of paired remote controls/radio tags/mobile device 17
3. Remote control D670 18
Switch on/off the remote control 19
LED indicator signals 19
Charging the remote control 20
Firmware update 20
Icons of the remote control 21
Quick access functions of the remote control 22
System settings menu 23
4. Immobilizer radio tag BT760 29
Functions of the button 30
Replacing an immobilizer tag battery 31
Update firmware of a radio tag 31

3
USER MANUAL
EN5. Control the system from a phone 32
Changing settings via a phone 33
6. Online service and mobile apps 37
Pandora Camper Pro 38
Mobile applications 40
7. Control the system 42
Using the application 40
Arming 43
Activating Stay Home mode 44
Delayed arming 45
Disarming 45
Locking/unlocking doors when ignition is on 46
Car search function 47
PANIC mode 47
Service mode 48
8. Control the system in case of emergency 49
Emergency disarming 51
Emergency control of the anti-theft functions 51
9. Warranty obligations 53
Installation certificate 55
Acceptance certificate 56
Warranty card 56

4SECURITY-SERVICE SYSTEM PANDORA CAMPER PRO
General information
1

5
USER MANUAL
ENSystem set
1. User manual and wiring diagram 1
2. Remote control D670 1
3. Radio tag BT760 2
4. Owner’s personal card 1
5. Base unit 1
6. External LED/VALET button 1
7. Beeper 1
8. Wireless door sensor DMS-100 BT 6
9. Siren PS-330 2
10. Cable of the base unit 4
11. USB cable 2
12. External temperature sensor 1
13. Blocking relay 2
14. Magnetic reed sensor 2
15. Fastening kit 1
16. Indoor module CIM-03BT 1
17. Packaging 1
! The manufacTurer reserves The righT To change The sysTem seT and consTrucTion of The producT To improve iTs
Technological and operaTional parameTers wiThouT noTificaTion.
Read the following section before using the system
Carefully read this manual before starting installation and using the security-service system. Pay
attention to text marked with !
! The sysTem is acomplex Technical producT. sysTem insTallaTion and configuraTion musT be carried ouT only by a
skilled professional.
! feaTures and sysTem modes, conTrol of The vehicles zones depends on The Type of connecTion and sysTem seTTings,
original vehicle operaTion logic and Trim.
! The sysTem seT includes an “owner’spersonal card”. This card conTains informaTion under aproTecTive layer ThaT
is inTended only for The owner of The sysTem. make sure ThaT The proTecTive layer on The owner’splasTic card is inTacT
afTer The insTallaTion of The sysTem.

6SECURITY-SERVICE SYSTEM PANDORA CAMPER PRO
!read The “owner’spersonal card” secTion of This manual before erasing The proTecTive layer.
! The sysTem has agsm inTerface. ask an insTaller who has insTalled The sysTem To check The gsm funcTions
operaTion using your phone:
• dial 500* command To requesT coordinaTes (see The “conTrol The sysTem from aphone” secTion).
• Trigger alarm when The sysTem is armed. The sysTem musT call your phone number (“main owner’sphone number”).
Toquickly change The “main owner’sphone number”, Turn on The igniTion when The sysTem is disarmed and call The
sysTem phone number. waiT for The answer, Then press and hold The buTTon on The radio Tag for 2 seconds (unTil The
second flash of The send indicaTor). release The buTTon, The sysTem will recognize The incoming phone number as
The “main owner’sphone number”.
• check The “guesT pin-code”(facTory defaulT value is 1-2-3-4). call The sysTem from an “addiTional phone number”
or from any oTher phone number unknown for The sysTem.
! The sysTem can work wiTh amobile applicaTion. iTis required To creaTe an accounT, add The sysTem To your accounT,
pair your mobile phone wiTh The sysTem. ask an insTaller To help you To configure The mobile applicaTion.
! when sysTem insTallaTion is finished:
• check ThaT The “insTallaTion cerTificaTe” and “warranTy card” are filled ouT. These documenTs may be required for
conTacTing The cusTomer supporT.
• check The sysTem operaTion and funcTions wiTh aspecialisT.
• werecommend ThaT you mark each working funcTion wiTh asign in The “conTrol The sysTem” secTion.
• ask an insTaller To mark The layouT of The sysTem componenTs on The diagram. This informaTion may be required for
diagnosTic/configuring or emergency deacTivaTion of The sysTem.
• werecommend ThaT you change The defaulT value of The “service pin-code” (1-1-1-1). ask an insTaller To change
The “service pin-code”.
wriTe down and remember a new value of The “service pin-code”
• werecommend ThaT you change The defaulT value of The “guesT pin-code” (1-2-3-4). (see The “changing seTTings
from aphone” secTion -> 5* addiTional seTTings -> 1* changing The guesT pin code.
wriTe down and remember a new value of The “guesT pin-code”
• ifThe “code immobilizer (pin-To-drive)” funcTion is implanTed:
wriTe down and remember The “immobilizer pin-code”
mark abuTTon (buTTon/lever/pedal) ThaT is used To enTer The “immobilizer pin-code” in The layouT diagram.

7
USER MANUAL
ENSystem modules layout
Base unit
Blocking relay (circuit
being blocked)
External VALET button
Sensor DMS-100 BT
1
2
3
4
5
6
7
8
9
10

8SECURITY-SERVICE SYSTEM PANDORA CAMPER PRO
Base unit of the system
Built-in GSM modem (GPRS/SMS/LBS-services)
A built in modem allows the system to work in a mobile network using an installed SIM card: voice
and SMS notifications, control from a phone using DTMF-commands, determination of coordinates
based on cellular base station location (only for 500* command), connection with our online-service
and mobile applications.
For the correct operation of the GSM functions, an owner should monitor the status/balance of the
SIM card installed in the system. If the SIM card is blocked or defective, GSM functions of the system will
be unavailable.
Built-in GPS/GLONASS-receiver
A built-in GPS/GLONASS-receiver is designed to determine current location and to automatically
determine date and time.
!ToauTomaTically deTermine daTa and Time, iT is required To seT correcT uTc Time zone using The mobile app or The
online-service.
2.4GHz radio channel, Bluetooth 5.0 protocol (BT5.0)
An integrated radio channel is used to connect the system with a mobile phone and additional
Bluetooth devices. The system supports up to 14 additional Bluetooth devices: 1 remote control D-030
or PandoraWatch 2, up to 3 radio tags, 1 mobile phone, up to 10 DMS-100BT sensors, up to 2 radio relays
BTR-101, 1 RHM-03BT or CIM-03BT module, 1 BT-01 relay or DI-04 module.
Digital protection AES (128 Bit)
Dialog coding of commands with a 128-bit encryption key guarantee secure communication via
the radio channel. The encryption key can be changed when you re-pair a remote control or additional
Bluetooth devices.
3D-accelerometer
A built-in accelerometer is used to detect shock/motion/tilt:
• 2 zones of the shock sensor (alarm/warning);
• Separate sensitivity adjustment by zones;
• Engine blocking on motion start;
• Central lock closing when start driving.

9
USER MANUAL
ENMultisystem digital 3CAN | 2xLIN interface
Integrated digital CAN and LIN interfaces allow connection to digital buses of a vehicle for reading
information (statuses) and controlling vehicles (commands). The LIN-interface can be used to control
Webasto ThermoTopEvo and Eberspacher Hydronic/Hydronic2 heaters.
!see deTailed informaTion on loader.pandorainfo.com
868 MHz Radio interface
A built-in radio channel is necessary for the communication with the remotes stored in the
system memory. 868 MHz frequency provides high-quality data transfer in the conditions of of radio
interference of a modern city.
Temperature
The system can determine interior, engine and outside temperature.The following sources are used:
built-in temperature sensor, connector of an external temperature sensor, digital CAN-bus, values from
additional devices.
! defaulT values: inTerior TemperaTe – builT-in sensor; engine TemperaTure – exTernal sensor; ouTside TemperaTure
– can.
Synchronized clock of the baze unit
Built in clock is automatically synchronized with the built-in GPS/GLONASS receiver
! iTis required To seT correcT uTc Time zone using The mobile app or The online-service.
Integrated power back-up
A built-in battery allows extending operating time of the system in the armed mode to promptly
notify an owner in the cases of an unauthorized disconnection of the onboard power supply. Power
supply from the back-up battery can be also occur in case of a short time voltage drop at the time of
starting the engine. If the back-up battery is discharged, the system automatically starts charging it
when the main power supply is active.
icro-USB port
The system has a buil-in micro-USB port that is used for system configuration and update via the
Pandora Alarm Studio.The system can be power from the USB, so you can configure it before installation.

10 SECURITY-SERVICE SYSTEM PANDORA CAMPER PRO
Owner’s personal card
! erase The proTecTive layer carefully. donoT use any sharp ob-
jecTs To avoid damaging of hidden informaTion under The proTecTive
layer. The informaTion is inTended only for The owner. The card and
The hidden informaTion cannoT be resTored.
The owner’s personal card contains private information
under a protective layer:
• PIN (the «Secret PIN-code”) is a 4-digit number.
This code can be used to disarm the system and to
deactivate immobilizer functions. It can be also used to
enter programming mode. This information cannot be
changed or restored
• LOGIN – is a 10-digit number. This information is used
to add the system to the online service and mobile
applications. This information cannot be changed or
restored
• PASS – contains 8 characters and can consist of digits, lower and upper case letters. This information
is used to add the module to the online service and mobile applications. This information cannot be
changed or restored.
• Phone number is a phone number of the SIM-card supplied with the system. This number is not used
if you change the SIM-card.
External VALET button
An external VALET button with a three-color status
LED indicator is placed inside a vehicle (see the system
modules layout). The button is used for programing
the system, arming/disarming, activating/deactivating
dimmobilizer mode.
!original vehicle conTrols (buTTons/levers/pedals) can be used as The valeT buTTon. see The deTailed informaTion
on loader.pandorainfo.com.
LED INDICATOR
VALET BUTTON
2-2-2-2
PIN