Pandora Camper Pro v2 User manual

Product is in conformity with Electromagnetic Compatibility
Directive EMC 2004/108/EC and R&TTE Directive 1999/5/EC
Pandora would like to thank you for
choosing our service-security system
Pandora Camper Pro v2 is a telemetric service-security system built for motorhomes with on-board
voltage of 12V. It is a complex engineering device, which includes unique and modern technological
software and hardware solutions.
When building the Pandora Camper Pro v2 we were using the most up-to-date electronics
from world’s best manufacturers. The device is built using high-precision mounting and controling
machinery, thus we guarantee highest possible quality, reliability and stable technical characteristics
for the whole operation period.
The Pandora Camper Pro v2 has a cryptographically strong authorization code with unique dialog
algorithm and individual encryption key on every device. It guarantees protection form electronic
hacking for the whole operation period.
The system is built for your convenience: it’s ergonomic, reliable, has the highest security and
service characteristics, 3 years unconditional warranty and free service and support. We are happy to
provide any support we can – feel free to use our online support.
! WARNING! ItIs stRoNGly AdvIsed to hAve pRofessIoNAl INstAllAtIoN of the system. ANy cAR electRoNIcs INstAlleR should be Able to
INstAll the system usING INstAllAtIoN scheme IN thIs mANuAl ANd the AlARm studIo softWARe. most feAtuRes ARe hIGhly depeNdeNt of
competeNt INstAllAtIoN. ouR systems ARe thoRouGhly tested foR quAlIty, so If AfeAtuRe fAIls to pRoduce expected Result, most lIkely the
pRoblem Is IN ImpRopeR INstAllAtIoN.
This device has limited external factors resistance. It should not be subjected to water beyond occasional splatter, or operated in
temperatures outside -40 to +85° C range. All system components must be installed only in a car interior.
The base unit, remote control and radio tags fulfil with the IP40 category of protection against water.
Our web-site: pandorainfo.com
Customer support: [email protected]

3
2USER MANUALPANDORA CAMPER PRO V2
Table of contents
General information 4
System set 4
Read before using 5
PIN codes of the system 6
Owner’s personal card 6
External VALET button 7
System modules layout 7
Base unit 8
Information signals of the system 10
System functions and modes 12
Security mode 12
Security zones 12
Remote and automatic engine starts 13
Stay Home mode 14
Slave mode 14
Owner authorization devices and functions 15
Checking the number of paired devices 16
Remote control (D-043) 17
LED SEND/ALARM indicator signals 18
Charging the remote control 18
Updating firmware of the remote control 18
Quick access functions 19
Icons of the remote control 20
Remote control menu 21
Check menu 21
Settings 22
Immobilizer radio tag 26
Function of the button 27
Replacing an immobilizer tag battery 27
Updating firmware of the tag 27
Control the system by a phone 28
Changing settings via a phone 30
Online-service and mobile applications 33
Control the system 36
Arming 36
Activating Stay Home mode 37
Disarming 38
Locking/unlocking doors when ignition is on 39
Car search function 40
PANIC mode 40
Remote engine start 41
Service mode 43
Control the system in case of emergency 45
Emergency disarming 46
Emergency control of the anti-theft functions 46
Additional devices 48
Warranty obligations 50
Installation certificate 51
Acceptance certificate 52
Warranty Card 52

5
4USER MANUALPANDORA CAMPER PRO V2
System set
1. Remote control 1
2. Radio tag 2
3. Leather case for a radio tag 1
4. Owner’s personal card 1
5. External VALET button 1
6. Beeper 1
7. Base unit 1
8. RF module RF-470 1
9. External GSM antenna 1
10. Camper Indoor Module CIM-03BT 1
11. Door Sensor DMS-100BT 5
12. External temperature sensors 1
13. Wires and fastening kit 1
14. Piezo siren PS-330 2
15. User manual 1
16. Wiring diagram 1
17. Packaging 1
! the mANufActuReR ReseRves the RIGht to chANGe the system set ANd coNstRuctIoN of the pRoduct to
ImpRove Its techNoloGIcAl ANd opeRAtIoNAl pARAmeteRs WIthout ANotIfIcAtIoN.
Read before using
Carefully read this manual before starting installation and using the security-service system. Pay
attention to text marked with !
! the secuRIty ANd telemetRIc system Is Acomplex techNIcAl pRoduct. system INstAllAtIoN ANd coNfIGuRAtIoN must be
cARRIed out oNly by AskIlled pRofessIoNAl.
! feAtuRes ANd system modes, coNtRol of the vehIcles zoNes depeNds oN the type of coNNectIoN ANd system settINGs,
oRIGINAl vehIcle opeRAtIoN loGIc ANd tRIm.
! the system set INcludes the “oWNeR’speRsoNAl cARd”. thIs cARd coNtAINs INfoRmAtIoN uNdeR ApRotectIve lAyeR
thAt Is INteNded oNly foR the oWNeR of the system. mAke suRe thAt the pRotectIve lAyeR oN the oWNeR’splAstIc cARd Is
INtAct AfteR the INstAllAtIoN of the system. ReAd the “oWNeR’speRsoNAl cARd” sectIoN of thIs mANuAl befoRe eRAsING
the pRotectIve lAyeR.
! WheN system INstAllAtIoN Is fINIshed:
• check the system opeRAtIoN ANd fuNctIoNs WIth AspecIAlIst.
• WeRecommeNd thAt you mARk eAch WoRkING fuNctIoN WIth AsIGN IN the “coNtRol the system” sectIoN
• check thAt the “INstAllAtIoN ceRtIfIcAte” ANd “WARRANty cARd” ARe fIlled out. these documeNts mAy be RequIRed foR
coNtActING the customeR suppoRt.
• Ask AN INstAlleR to mARk the lAyout of the system compoNeNts oN the dIAGRAm. thIs INfoRmAtIoN mAy be RequIRed foR
dIAGNostIc/coNfIGuRING oR emeRGeNcy deActIvAtIoN of the system.
WeRecommeNd thAt you chANGe the defAult vAlue of the pIN-codes of the system. you cAN WRIte doWN the chANGed
pIN-codes IN the “pIN-codes of the system” sectIoN.

7
6USER MANUALPANDORA CAMPER PRO V2
PIN-codes of the system
The “Secret PIN-code”
(is written on the “Owner’s personal card”)
The “Service PIN-code”
(default value is 1-1-1-1)
The “Guest PIN-code”
(default value is 1-2-3-4)
The “Immobilizer PIN-code”
(is used for the Validator (pin-to-drive) function)
! ItIs RecommeNded thAt you WIll WRIte doWN the chANGed oR cReAted vAlues of All pIN-codes. elImINAte thIRd-pARty
Access to thIs INfoRmAtIoN.
Owner’s personal card
! eRAse the pRotectIve lAyeR cARefully. doNot use ANy shARp objects to AvoId dAmAGING of hIddeN INfoRmAtIoN uNdeR
the pRotectIve lAyeR.
The owner’s personal card contains private information under a protective layer:
• PIN (the“Secret PIN-code”) is a 4-digit number.This code can be used
to disarm the system and to deactivate immobilizer functions and
to activate service mode. It can be also used to enter programming
mode.
• LOGIN is a 10-digit number. This information is used to add the
system to the online service and mobile applications.
• PASS contains 8 characters and can consist of digits, lower and
upper case letters). This information is used to add the system to the
online service and mobile applications.
• Phone number is a phone number of the built-in SIM-chip.
CANNOT BE CHANGED
+7-9хх-ххх-хх-хх
1070000000 / Y34aC4vJ
2-2-2-2
LOGIN / PASS
PIN PHONE NUMBER
System modules layout
External VALET button
(VALET button via CAN)
Button for the immobilizer
PIN
Circuit being blocked
Base unit
DMS-100BT
1
2
3
4
5
6
7
External VALET button
An external VALET button with a three-color status LED indicator is placed
inside a vehicle (see the system modules layout).
The button is used for programing the system, arming/disarming,
activating/deactivating immobilizer mode.

9
8USER MANUALPANDORA CAMPER PRO V2
WARNING! dms-100bt seNsoRs fRom the kIt ARe AlReAdy pAIRed WIth the bAse uNIt. AccoRdING to the INstAllAtIoN
plAce you cAN chANGe the defAult loGIc of the AlARm zoNes IN AlARm studIo oR pANdoRA specIAlIst: «AdvANced
settINGs»-»INputs ANd outputs»-»INputs settINGs». fIll the tAble WIth the ActuAl loGIc:
DMS1 Window DMS6
DMS2 Window DMS7
DMS3 Trunk DMS8
DMS4 Trunk DMS9
DMS5 Hatch DMS10
Base unit
Built-in GSM modem (2G/3G/4G LTE) provides a connection with our online-service pandora-on.
com and mobile application (Pandora Connect), allows to control the system by a phone using DTMF-
commands, voice and SMS notifications, automatic date and time detection. The modem operates in a
mobile network using the built-in SIM-chip or/and a nano-SIM.
Built-in SIM-chip is and integrated SIM-card chip that it used to work with the built-in GSM modem.
The built-in SIM-chip has a tariff plan for Russia (phone number is written on the “Owner’s personal
card”).
Built-in slot for a nano-SIM is used for owner’s SIM-card (nano-SIM). If both the SIM-chip and SIM-
card are used in the system, there is a function that allows to automatically switch between the SIM-chip
and the SIM-card if there is no internet connection.
!ItIs RequIRed to INstAll AN AddItIoNAl sIm-cARd IN the NANo-sIm slot foR the AutomAtIc mode.
Built-in GPS/GLONASS-receiver is designed to determine current location and to automatically
determine UTS date and time.
2.4GHz radio channel, Bluetooth 5.0 protocol (BT5.0) - supports up to 14 additional Bluetooth
devices (see the“Additional devices”section), including a mobile phone.
Built-in 3D accelerometer is used to detect shock/motion/tilt including 2 separate zones of shock
sensor (alarm and warning), the system allows to adjust sensitivity of each zone, to use data from the
accelerometer to block the engine and close the central lock on movement.
Temperature sensors allow the system to measure temperature of different zones to send
this information to the remote control or mobile apps. The following zones are available: interior
temperature – built in sensor of the main unit, engine temperature – external temperature sensor (see
the “System set”), outside temperature – digital car protocol*
The system setting allow you to reassign sensor to different zones and use information from external
additional devices (PS-331BT, CIM-03 BT, DMS-100 BT); to implement automatic engine or engine pre-
heater starts and stops by temperature.
Emergency power – the system has an input for an external back-up battery in order to notify an
owner in case of power disconnection in armed mode. The battery will be charged automatically when
engine is running.
Built-in digital 3хCAN/2xLIN* interface allows the system to read status end exucute commands
via digital buses, and work with Webasto Thermo Top Evo  Eberspacher Hydronic/2.
Built-in digital IMMO-KEYport and immobilzer bypass* – hardware and software algortihms
with the special Pandora CLONE server allow the system to bypass original immobilizers for automatic
and remote engine starts.
Built-in micro-USB port – update and configuration of the system using a PC and Pandora Alarm
Studio.
! *moRe INfoRmAtIoN Is AvAIlAble oN loAdeR.pANdoRAINfo.com
RF-module RFМ-470 is an external antenna that provides wireless
communication between the system and remote controls.
868MHz Antenna, LoRa modulation supports up to 4 remote
controls D-043 LoRa, D-022 LoRa.
2.4GHz Antenna, Bluetooth 4.2 protocol provides connection
between the base unit and the RF-module.
CALL button is an integrated button. Press and hold the button for
1 second or more, the remote control will indicate“CALL”.
2,4 GHz
Antenna
868 MHz
Antenna
CALL
button

11
10 USER MANUALPANDORA CAMPER PRO V2
Information signals of the system
LED INDICATOR SIGNALS
SIGNALS DESCRIPTION
THE SYSTEM IS ARMED
Short red ashes System is armed
Short green ashes System is armed
(an authorization device is in the coverage zone)
Fast red ashes Alarm
THE SYSTEM IS DISARMED
Faded System is disarmed
Red System is preparing for automatic or delayed arming
Green (when ignition is on) System is in service mode
Green ashes
(when switching on the ignition) Conrms the number of paired radio tags
Red ash
(when switching on the ignition) Conrms a paired mobile device
WHEN ENTERING THE“SECRET PIN-CODE”OR THE“SERVICE PIN-CODE”
Orange ash Conrms a VALET button press
Short red ash Conrms a digit input
PIN-code is incorrect
Red and green ashes Conrms correct PIN code
SOUND AND LIGHT SIGNALIZATION
SIGNALS
(sound / light) DESCRIPTION
1х /1х Arming
2х /2х Disarming
5х /5х Car search
30 sec. /30 sec. Alarm, PANIC mode
3х /1х Warning level of a sensor is triggerd
4х /4х
Sensors were triggered’signal when disarming /
Parking light is not turned o notication /
‘Sensors are triggered”signal when arming
25 sec. /25 sec. Engine blocking warning in Anti-Hi-Jack mode
BEEPER SOUND SIGNALS
SINGNAL DESCRIPTION
1 sound signal Activating service mode
2 sound signals Deactivating service mode
1 sound signal Correct input of the“Immobilizer PIN-code”
3 sound signals/3 times A battery in a radio tag is discharged
4 sound signals/4 times Absence of a an authorization device when you switch
on ignition
Fast sound signals Engine blocking warning

13
12 USER MANUALPANDORA CAMPER PRO V2
SYSTEM FUNCTIONS AND MODES
Security mode
The system confirms arming with 1х sound and 1х light signals. When the system is armed, the
system monitors security zones with separated warning and alarm level of triggering:
• Warning mode - this mode activates when there is a slight impact on the shock sensor or additional
senor. It is accompanied with 1х light and 3х sound signals;
• Alarm mode - this mode activates when a sensor or one of the security zones is triggered.
It is 30 sec. light and 30 sec. sound signals. he alarm signals can be
• canceled by an arming or disarming command.
If one of the security zones is triggered the system:
• records this event in its non-volatile memory;
• activates the alarm or warning mode;
• informs an owner by all available means;
• blocks the engine (in accordance with the settings and connections).
• If one of the security zones is opened at the moment of arming, the system will produce 4х
sound and 4х light warning signals.
If one of the security zones fails, the system will forcibly turn off this zone. If a switch triggers
more than 9 times in a row, it will be disabled until the next arming. The shock/tilt/motion sensor is
temporarily deactivated (15 sec.) if it has been triggered more than 3 times in a row.
The system confirms disarming with 2х sound and 2х light signals. The system deactivate
engine blocking (if the immobilizer function and additional blocking are not used). If there were alarm
events during the armed period, the system will produce 4х sound and 4х light warning
signals. The system continues to display all zones when it is disarmed, but the information is not saved
in the memory.
Security zones
• Interior temperature (status)
• Engine temperature (status)
• Outside temperature (status)*
• Voltage of the on-board circuits (status)
• Engine operation control - RPM (status)
• Heater operating control (status)
• Fuel level (status)
• Parking (automatic gearbox) /Handbrake (manual gearbox) status
• Parking light is not turned off” notification (status)
• Shock sensor (security zone – alarm and warning level)
• Motion sensor (security zone – alarm level)
• Tilt sensor (security zone – alarm level)
• OE alarm system status via CAN, additional sensor (status, security zone – alarm and warning level)
• Turning ignition on (status, security zone – alarm level)
• Opening front doors (status, security zone – alarm level)
• Opening side doors (status, security zone – alarm level)
• Opening camper windows (status, security zone – alarm level)
• Opening camper sunroofs (status, security zone – alarm level)
• Opening a trunk (status, security zone – alarm level)
• Opening a hood (status, security zone – alarm level)
• Pressing brake (status, security zone – alarm level)
!*outsIde tempeRAtuRe Is AvAIlAble by AN AddItIoNAl devIce (see the “AddItIoNAl devIces” sectIoN) oR by cAN-bus dAtA
(see loAdeR.pANdoRAINfo.com).
Remote and automatic engine starts
The system allows for remote engine start using the “remote engine start” command from a remote
control, mobile application or preconfigured automatic engine start function. Remote start can be used
to heat engine and interior, charge battery or to cool the interior with air conditioning.
Remote and automatic starts can only be used when the system is armed. While the system is in
remote or automatic start mode, it keeps performing all security functions of all of the security zones
excluding a shock sensor (the system can be configured to not disable the shock sensor during a remote
engine start). To compensate it, the motion sensor sensitivity and responsiveness will be increased. If
any security zone will be triggered, the engine will be immediately stopped and alarm mode will be
triggered.
When using the remote and automatic engine start functions, make sure that a car is secured with
handbrake or some other means of fixating the car on a parking position.
Remote and automatic engine start on automatic transmission cars will only occur, if a transmission
selector lever was left in the «P» position.
If a car has manual transmission, remote or automatic start will only occur if the program neutral
procedure was followed when the car was arming.

15
14 USER MANUALPANDORA CAMPER PRO V2
AN EXAMPLE OF THE PROGRAM NETURAL PROCEDURE
1. When the engine is running, fixate the car with the handbrake and put gear lever to the neutral
position. Program neutral procedure will be switched on automatically (by default system settings).
2.Turn the key in the ignition lock to the OFF position (the engine should still be running) and take
it out of the lock (skip this step for cars with a Start/Stop button).
3.Leave the car, close the doors.
4.Arm the system - the engine will be stopped. Now the system is ready to perform remote and
automatic engine start.
Automatic starts
The system allows configuring automatic engine start and stop conditions. Automatic starts can be
configured using a remote control or mobile application. The following conditions can be specified for
automatic engine starts: schedule, time period, engine temperature, voltage. The engine will be stopped
automatically after specified time or when the engine temperature reaches a specified value. The engine
can be also stopped by a user command
! AutomAtIc eNGINe stARts ANd stops by tempeRAtuRe ARe AvAIlAble oNly If AtempeRAtuRe seNsoR Is coNNected. Remote
ANd AutomAtIc eNGINe stARts ARe Not AvAIlAble If the tRuNk Is opeN.
Stay Home mode
This mode is used to control the outer perimeter of a vehicle during parking when passengers are inside
the vehicle. This mode allows the system to protect your vehicle against intrusion through the parts of
the vehicle that can be open.
• The system will be armed silently when you activate the “Stay Home” mode, it will be confirmed
with 1х light signal. The system controls vehicle security zones and an additional gas sensor (it is
not included in the set) in this mode, built-in sensors (shock/tilt/motion) are disabled in this mode.
The system will be disarmed when you deactivate the“Stay Home”mode, it will be confirmed with 2х
sound and 1х light signals.
Slave mode
This mode allows arming and disarming using original vehicle control – an original key, button/
sensor of a keyless access entry system.
Slave mode can be implemented using analog connections or a digital protocol of a vehicle.
!thIs mode Is dIsAbled by defAult foR AdIGItAl pRotocol. moRe INfoRmAtIoN oN loAdeR.pANdoRAINfo.com. ItIs
RecommeNded to ActIvAte the “pRohIbIt dIsARmING WheN AtAG Is AbseNt” to INcReAse secuRIty feAtuRes of the slAve
mode. IfthIs mode Is ActIvAted, It WIll be possIble to dIsARm the system oNly WheN AtAG Is IN the coveRAGe zoNe oR usING
the “secRet pIN-code”.
Owner authorization devices and functions
Authorization devices
Authorization devices are Bluetooth devices paired with the system (radio tags, remote control D030,
mobile phone with the app). The devices are used to recognize an owner in the radio coverage zone
of the base unit to arm/disarm the system (Hands Free mode) and to implement immobilizer or Anti-
Hi-Jack functions.
!INstAll the beepeR If you use AuthoRIzAtIoN devIces.
Hands Free mode
This mode is used for automatic arming/disarming when an owner with an authorization device is
distancing or approaching a vehicle.
!thIs mode Is dIsAbled by defAult. ItIs RequIRed to mAke AddItIoNAl settINGs usING the mobIle ApplIcAtIoN oR pANdoRA
AlARm studIo to use thIs mode. quIck Access commANds to mANAGe hANds fRee mode: 223* - ActIvAte hANds fRee
ARmING, 224* - ActIvAte hANds fRee dIsARmING, 222* - deActIvAte All hANds fRee modes.
Immobilizer mode
This mode is used to recognize an owner using authorization devices when the system is disarmed.
When turning on the ignition, the base unit performs a search for authorization devices in the
radiocoverage zone. If there is no any authorization device in the radio coverage zone, the system
will block the engine. Engine blocking will occur immediately or at the time a motion sensor detects
movement, it depends on the system settings. When an authorization device appears in the coverage
zone, the system will exit blocking mode and will continue to work in normal mode.
!thIs mode Is eNAbled by defAult. ItIs RequIRed to mAke AddItIoNAl coNNectIoNs foR thIs mode.
ANTI-HI-JACK-1/2 modes
The Anti-Hi-Jack modes help to prevent aggressive seizure of a vehicle when authorization in case
of disappearance of authorization devices from the radio coverage zone when system is disarmed.

17
16 USER MANUALPANDORA CAMPER PRO V2
ANTI-HI-JACK-1 mode – The base unit checks if an authorization device is in the radio coverage zone
each time when ignition is on and a door is opened/closed.
ANTI-HI-JACK-2 mode – The base unit constantly checks if an authorization device is in the radio
coverage zone when ignition is on.
If the system cannot detect an authorization device, the base unit will perform a delayed engine
blocking. The siren will play the ‘Engine blocking warning’ ringtone before blocking. The engine will
be blocked immediately or at the time the car starts moving, it depends on the system settings. When
an authorization device appears in the coverage zone, the system will exit blocking mode and will
continue to work in normal mode.
!thIs mode Is dIsAbled by defAult. thIs mode cAN be set oNly by ApRofessIoNAl specIAlIst
Multi-button code immobilizer (pin-to-drive)
• Multi-button code immobilizer (pin-to-drive) is a function that allows disarming, disabling blocking
and controlling service mode and time channels using original vehicle controls (button, lever or
pedal) and a pre-programmed PIN-code (the “Immobilizer PIN-code”).
AN EXAMPLE OF USING THE FUNCTION
• Turn on the ignition to disable engine blocking or enable service mode, turning on the ignition is not
required if you want to disarm the system or control time channels.
• Enter the “Immobilizer PIN-code”. Press a programmed button/lever/pedal the number of times
equals to the first digit. Pauses between presses should not exceed 1 second. More than 1 second
pause will be interpreted as the start of the next digit input. The immobilizer code can consist max
of 4 digits from 1 to 9.
• The system will confirm the correct input by a sound signal of the beeper and a programmed
• function will be performed.
!thIs mode Is dIsAbled by defAult. thIs mode cAN be set oNly by ApRofessIoNAl specIAlIst.
Checking the number of paired devices
The number of paired radio tags/mobile device can be checked by the number of flashes of the
LED indicator. The number of tags/mobile device can be checked when switching on the ignition (the
system must be disarmed). The number of green flashes will indicate the number of paired radio tags, a
following red flash will indicate a paired mobile device.
You can also check the number of paired radio tags/mobile device by taking off and putting back on
battery terminal. The system will emit short sound signals from a siren :
• First series of the siren signals – indicates the number of paired radio tags;
• The second long signal after a pause of 2 seconds indicates a paired mobile devices.
REMOTE CONTROL D043
A two-way remote control is a mean of control over the system.
For easily distinguishable notifications the remote uses 16 ringtones. Each ringtone matches a
particular event. Remote has flashing LED indicators for additional information.
The remote is fully operational when shipped. To switch on the remote, press and hold the
button for 3 seconds. The“REMOTE ON” ringtone will play. Pressing and holding this button again for 3
seconds will cause the remote to switch off.
!All coNtRol commANds ARe tRANsmItted vIA RAdIo chANNel, foR mAxImum effectIveNess ANd RANGe It Is RecommeNded
Not to shIeld AeRIAl AReA (see pIctuRe) WIth fINGeRs WheN usING ARemote coNtRol.
! A Remote coNtRol Is AuNIfIed coNtRol devIce. Its fuNctIoNs depeNd oN secuRIty system model.
868MHz
Antenna
SEND/ALARM
Indicator
OLED-
DISPLAY
micro-USB
ARM
DISARM
Unlock trunk
Beeper

19
18 USER MANUALPANDORA CAMPER PRO V2
SEND/ALARM indicator signals
Green indicator:
• Flashes if there is a connection with the base unit
• Goes dark when there is no connection with the base unit
Red indicator:
• Flashes frequently if there is any notification
• Flashes occasionally when there is no connection.
Charging the remote control
• Battery is charged
• Battery is discharged
There is battery charge level indication on the display of the remote control. Charge the battery if
the remote control doesn’t turn on or the charge indicator displays low level. Charging is performed
using a standard micro-USB cable.
Firmware update
• Run the Pandora Alarm Studio application on a PC with Windows XP/Vista/7/8/10 and connect a
USB-cable to it.
• Press and hold the , button and connect a USB cable. Release the button after connection. The
remote control and the app will enter boot mode.
• Press the “Update software” button in the Pandora Alarm Studio and select one of the following
options: “Firmware archive” – it will upload firmware from the server to the firmwares folder of the
Pandora Alarm Studio;“Load from file” – select a file with firmware on your PC.
• Start uploading by pressing the “Upload” button.
• Disconnect the USB-cable after completion of the procedure
Quick access functions of the remote control
System is disarmed System is armed
(no alarm events)
Ignition is on Ignition is o
(short press) Lock doors without arming Arming with a sound
confrmation
Search mode – flashes of
turn signals with sound
signals for 5 seconds
(1 sec.) Activating «StayHome»
mode
Search mode – flashes of
turn signals with sound
signals for 5 seconds
(2 sec.) Switch on ‘Ignition
maintenance’ mode
(3 sec.) Switch on“Program neutral”
(reservation mode) Remote engine start
(short press) Unlock doors Unlock doors Disarming with a sound
conrmation
(1 sec.) Disarming without a sound
conrmation
(2 sec. and more) Switch o ‘Ignition
maintenance’ mode
Switch o the ignition
during remote or automatic
engine start procedure
(short press) Switch on LCD lighting (available only on the remote with LCD)
(1 sec.) Unlock trunk
(2 sec.) Additional function via CAN
(3 sec.) Switch on/o the remote
+
(short press) PANIC mode
+ (short press)
Arming when the engine
is running with sound
conrmation
Arming in 30 seconds with
a sound notication
+ (1 sec.)
Arming when the engine
is running without sound
conrmation
Arming in 30 seconds
without a sound
notication

21
20 USER MANUALPANDORA CAMPER PRO V2
Icons of the remote control
*Separate display indication of doors, original alarm status, fuel level depend on information in CAN-bus digital protocol of specific car.
Flashing when
command sending
Security mode
status
Battery level
Current time
Vehicle battery
voltage
Interior
temperature
Engine
temperature*
Fuel level*
Ignition
security zone
Tilt sensor security
zone
12 48
Additional sensor/ OE alarm
status Security zone
(alarm level)
Additional sensor/ OE alarm
status Security zone
(warning level)
Shock sensor Security zone:
Warning level;
Alarm level
Motion sensor security zone
Doors security zone*
Front hood security zone
Trunk security zone
Low voltage security zone
Handbrake/neutral indicator,
Brake pedal
Engine operation icon
P
22
°
90
°
55
1
2
.4
Remote control menu
You can control and manage all main settings and parameters of the system using the menu of the
remote control.
Briefly press the , button to enter the menu. The following presses of the button will switch
between menu items. Press the or button to enter a selected item.
Check menu
To get information about engine temperature, interior temperature, battery voltage and fuel level,
select the CHECK menu by short presses of the button and briefly press the or button.
If there are no any actions within 5 seconds, the remote control will exit the main menu automatically.
You can manually exit the menu by pressing the button.
PROCEED TO THE MENU
(press briefly)
GO TO THE NEXT ITEM
(press briefly)
GO TO THE NEXT ITEM
(press briefly)
EXIT THE MAIN MENU
(press briefly)
ENTER THE MAIN MENU
(press briefly)
F
F
F
F
or
PROCEED TO THE MENU
(press briefly)
or
PROCEED TO THE MENU
(press briefly)
or
CHECK
SETTINGS
INFORMATION
12 4V
22 °
90°
55
Battery
voltage
Interior
temperature
Engine
temperature
Fuel
level

23
22 USER MANUALPANDORA CAMPER PRO V2
Settings
To change settings and parameters of the system, select the SETTINGS menu by short presses of the
button and briefly press the or .
Briefly press or , button to select a sub-menu.
To enter a sub-menu, briefly press button.
decrease
Enter/confirmation button
parameter
is enabled
parameter
is disabled
save parameter
exit a manu/submenu
Navigation buttons
increase
up
down
PROCEED TO THE SETTINGS MENU
(press briefly)
or
PROCEED TO THE SETTINGS/PARAMETERS
(press briefly)
MENU NAVIGATION
(press briefly)
up
down
EXIT THE MENU
(press briefly)
F
F
HISTORY
AUTOSTART
HEATER
SENSORS
TRACKING
SIREN
HANDS FREE
CHANNELS
GPS RECEIVER
GSM MODEM
VALET MODE
SETTINGS
HISTORY VIEW EVENT HISTORY
This menu allows viewing the event history stored in the remote control memory. The remote control
displays an event name and its time.
! the NumbeR of eveNts Is lImIted by the memoRy of the Remote coNtRol.
AUTOSTART AUTOMATIC ENGINE START SETTINGS
This menu allows configuring the automatic engine start and stop settings. A synchronized real-
time clock in the remote control and the base unit and other autonomous system settings allow to
implement set of conditions of engine start and operation regardless of whether the remote control is
in the radio coverage zone or not.
• ENABLE - this submenu switches on/off all automatic engine starts.
• TIMER - this submenu allows starting an engine every day at the scheduled time.
• START TEMP - this submenu allows starting an engine automatically when the engine temperature
is low.
• WORK TIME - This submenu determines the maximum engine operation time for automatic and
remote starts.
• PERIODICALLY - this submenu allows starting engine periodically with a configured time interval.
• STOP TEMP - this submenu determines the engine stop temperature.
! Ifyou hAve Not sAved NeW settINGs, Remote ANd AutomAtIc eNGINe stARt settINGs WIll RemAIN the sAme As befoRe.
eNGINe stARt vIA tempeRAtuRe Is AvAIlAble oNly If tempeRAtuRe seNsoR Is coNNected. AutomAtIc eNGINe stARt settINGs
doN’tAffect Remote eNGINe stARt fuNctIoNs.
HEATER CONTROL OVER AN ENGINE PREHEATER
This menu allows switching on/off an engine pre-heater.
SENSORS SETTINGS AND ADJUSTMENT OF THE SENSORS
This menu allows controlling and adjusting sensors (shock/motion/tilt) sensitivity. SHOCK and
additional EXTERNAL sensors have separate sensitivity zones. Alarm zone triggers when there are
considerable impact on a sensor. If the alarm zone is triggered, the system will indicate it with light and
sound alarm for 30 sec. Warning zone triggers when there are minor impact on a sensor (the sensitivity
of the warning zone should be higher than the alarm level sensitivity for correct operation). Warning
level is indicated by one light and three sound signals.

25
24 USER MANUALPANDORA CAMPER PRO V2
• SHOCK — This submenu allows adjusting sensitivity of the alarm and warning zones of
the shock sensor.
- Warning and alarm zones are enabled.
- Warning and alarm zones are disabled.
- Warning zone is disabled.
• MOTION — This submenu allows adjusting sensitivity of the motion sensor.
-   .
-   .
• TILT — This submenu allows adjusting sensitivity of the tilt sensor
- Tilt sensor is enabled.
- Tilt sensor is disabled.
• EXTERNAL — This submenu allows adjusting sensitivity of the alarm and warning zones of
the additional sensor.
- Warning and alarm zones are enabled.
- Warning and alarm zones are disabled.
- Warning zone is disabled.
TRACKING TRACKING
This menu allows you to switch on and off the tracking function for online services
SIREN OPTIONS OF SIREN SOUND SIGNALS
This menu allows configuring siren sound notifications.
- all sound signals are enabled.
- warning signals are disabled.
- warning and alarm signals are disabled.
HANDS FREE SETTINGS OF THE HANDS FREE MODE
This menu allows configuring the Hands Free mode for arming/disarming.
- Enable arming in the Hands Free mode.
- Enable disarming in the Hands Free mode.
- Enable arming and disarming in the Hands Free mode.
- Disable arming and disarming in the Hands Free mode.
CHANNELS TIME CHANNEL CONTROL
This menu allows switching on/off time channels. These channels are used to implement additional
functions and to control external devices. The channels are configured using the Pandora Alarm Studio
application.
GPS RECEIVER COORDINATES DETECTION
This menu allows you to switch on and off detection of GPS/GLONASS coordinates.
GSM MODEM MANAGE THE BUILT-IN MODEM
This menu allows you to switch on and off the built-in GSM-modem.
VALET MODE SERVICE/VALET MODE
his menu allows activating/deactivating the service (valet) mode (see the “Service mode”section)
SETTINGS SETTING OF THE REMOTE CONTROL
This menu allows configuring the remote control operation.
• SOUND — This submenu allows switching on/off sound signals.
• VIBRO — This submenu allows switching on/off vibrations.
• BACKLIGHT — This submenu allows adjusting LCD backlight brightness.
• RFM LOST — This submenu allows configuring sound notifications in case of losing connection
between a remote control and a base unit
- Disable notification signals.
- Enable notification by“Connection is lost”ringtone.
- Enable notification by“ALARM”ringtone. The“ALARM”ringtone will be played if the system is armed.
The system will notify you with a short signal one time per minute after the ringtone. The notifications
will come until the connection is established or the notification can be canceled by a short press of
button. If the system is disarmed only one“Connection is lost” ringtone will be played.
• TIME - This menu allows you to set time of the remote. It is required to arm and disarm the system
after to send the changed value to the base unit.
! dAte ANd tIme detectIoN Is peRfoRmed AutomAtIcAlly foR systems WIth Gsm.
INFORMATION To get technical information about the remote control, select the INFORMATION
menu by short presses of the button and briefly press the button.

27
26 USER MANUALPANDORA CAMPER PRO V2
IMMOBILIZER RADIO TAG
A radio tag is a device used to control a vehicle/system. The tag is also used as an authorization device
for “Immobilizer/Anti-Hi-Jack/Hands Free” modes. It works in the Bluetooth coverage zone. The radio
tag has:
- a control button for arming/disarming and activating/deactivating service mode;
- a built-in accelerometer allows the tag to go into energy saving mode when there is no movement;
- an LED indicator SEND.
• Control button for arming/disarming and activating/
deactivating service mode
• LED indicator SEND
• Bluetooth protocol
• Built-in accelerometer
• CR 2032 Battery
Light indication of the SEND indicator when there is a
short press of the button
• No flashes – a battery is discharged
• 1 flash – radio tag operation is correct
Light indication of the SEND indicator when installing a battery
• No flashes – a battery is discharged
• 1 flash – low battery level
• flashes – high battery level
!AvoId moIstuRe oN the RAdIo tAG. doNot plAce the RAdIo tAG NeAR mAGNets oR pRoducts WIth self-mAGNetIc fIelds
SEND
Functions of the button
ACTION FUNCTION
Press and hold for 2 sec when the
system is disarmed and ignition is o Activate Stay Home
Short press when ignition is o Arm/disarm
Press and hold for 2 sec when the
system is disarmed Change the “Main owner’s phone number”
Press and hold for 3 sec when ignition
is on Activate/deactivate Service mode
Press and hold for 6 sec. Pair a tag with the base unit
Press and hold for 10 sec. Firmware update
Replacing an immobilizer tag battery
Carefully open the cover of the tag’s battery compartment. Extract discharged battery and insert a
new one keeping in mind the correct polarity. Replacing a battery will not cause a loss of tag code
information, as authorization data is stored in the non-volatile memory of the MCU. Carefully close the
cover of the tag’s battery compartment. All elements of construction should be rigidly locked in places.
If it is so, the tag can be operated as usually.
Updating rmware of the tag
• Download the Pandora BT application (for Android or iOS devices equipped with a Bluetooth 4.0 Low
Energy or higher module).
• Open the mobile app Pandora BT.
• Press and hold the button of the radio tag until the 10th flash of the «SEND» indicator, then
release the button.
• Select the found device and select one of the update option: FILE MANAGER – firmware will be
uploaded from the phone storage (only for Android). INTERNET – firmware will be uploaded by an
internet connection.

29
28 USER MANUALPANDORA CAMPER PRO V2
CONTROL THE SYSTEM BY A PHONE
! foR the coRRect opeRAtIoN of the Gsm fuNctIoNs, AN oWNeR should moNItoR the stAtus/bAlANce of the sIm cARd
INstAlled IN the system. Ifthe sIm cARd Is blocked oR defectIve, Gsm fuNctIoNs of the system WIll be uNAvAIlAble.
Call the system’s phone number. When it answers, enter a command code
*ItIs RequIRed to eNteR the “secRet pIN-code” AfteR dIAlING AcommANd.
DTMF commands.
For example: To have simple access to engine start function, create a new contact in the contact
list of your phone, name it ‘Engine start’, for instance, and add the number in the following format:
+XXXXXXXXXXX,123*,297* where “+XXXXXXXXXXX” – the system phone number, “,” - pause is a feature
of the phone (can be displayed as the‘P’, see the instructions of the phone),“123*” - remote engine start
1
10 00 0*
*
1
12 23 3*
*
5
5
1
1*
*Tow truck mode
Request GSM account balance
Start the engine/prolong heating
3
32 21 1*
*Stop the engine
3
33 33 3*
*Switch on add. function using F via CAN
5
50 00 0*
*
4
45 56 6*
*
6
65 54 4
*
*
7
75 53 3*
*
Request current coordinates
Switch on additional channel
Switch o additional channel
#
#
9
9*
*
*
*
1
15 59 9*
*
Return to previous menu
Repeat the last message
Silent arming
Help
0
0
0
0*
*
0
0
1
1*
*
Unlocking trunk
Silent disarming
1
1*
*Arming
0
0*
*Disarming
Force connection to the server
2
25 58 8*
*System information
1
15 56 6*
*
6
65 51 1*
*
Switch on engine preheater
Switch o engine preheater
6
66 66 6*
*
9
99 99 9*
*
Enable engine blocking
Disable authorization devices*
9
99 98 8*
*
8
88 88 8*
*
Отключение устройств авторизации*
4
42 24 4
*
*
Fuel level calibration
Enable authorization devices
2
22 22 2*
*Disable Hands Free mode
2
22 23 3*
*Enable Hands Free arming
2
22 24 4*
*Enable Hands Free disarming
2
22 25 5*
*Enable Hands Free disarming
only with autom. start
7
78 89 9*
*Enable automatic engine start
9
98 87 7*
*Disable automatic engine start
2
29 97 7*
*End call
5
55 51 1*
*Enable service mode (see description below)*
5
55 52 2*
*Disable service mode
DTMF command, “297*” - end call DTMF command. Contact can be added as a speed dial to any of the
free button.To have simple access to engine start function a phone other than the main owner’s phone,
create contact in the following format: +XXXXXXXXXXX,1234,123*,297* where‘1234’ – guest PIN-code.
Activate/Deactivate service mode
1. Call the system number. Wait for the answer.
2. Turn on the ignition, an authorization device (a radio tag, a remote control, a paired mobile phone
with the app installed) must be in the coverage zone, enter the “Immobilizer PIN-code” (if the “Code
immobilizer” function is enabled).
3. To activate service mode, dial the 551* DTMF command — “Activate service mode”, then enter the
“Secret PIN-code”from the owner’s personal card.
4. To deactivate service mode, dial the 552* DTMF command — “Deactivate service mode”.
Voice help
The system has a voice help menu. During a voice call to the system, dial 9* and listen to the information
about system control commands.
To end the session, hang up the phone.
Repeat the last message
To repeat any message, press *during a voice call to the system.
Arming/Disarming
1. Call the system number. Wait for the answer.
2. Dial 1* to arm, and 0* to disarm. For silent arming dial 10* or 00* for silent disarming
3. The system will confirm arming/disarming.To end the session, hang up the phone. Enabling/disabling
automatic engine starts Pandora systems have a function of prompt disabling automatic engine start:
1. Call the system number and wait for the answer.
2. Dial 987* to disable all automatic engine starts or 789* to enable.
3.The system will confirm execution of the command.To end the session, hang up the phone. Automatic
starts can be enabled again by dialing 789* (all previous settings will remain intact).
Request current coordinates
1. Call the system number. Wait for the answer.
2. Dial 500*.
3. The system will confirm: ‘Current coordinates are sent via text message’ and will send text message

31
30 USER MANUALPANDORA CAMPER PRO V2
with coordinates and a web link to a map to your phone.
To end the session, hang up the phone.
Request GSM balance
1. Call the system number. Wait for the answer.
2. Dial 100*.
3. The system will confirm:‘Balance information is sent via text message’and will send text message with
account balance information to your phone.
To end the session, hang up the phone.
Tow truck mode
This mode is intended for car transportation with preservation of arming function. Tow truck mode
can be activated only when the system is armed, it will be deactivated automatically when disarming.
1. Call the system number. If the system is in PANIC mode, receive an emergency call. Wait for the answer.
2. Dial 15*, to enable the “Tow truck” mode, the system will disable motion, shock and tilt sensors. To
end the session, hung up the phone.
3. To disable this mode, disarm the system.
Activating/Deactivating engine blocking
You can block a car engine using any phone. The engine will remain blocked until phone command
‘Unlock engine’will be sent and the “Secret PIN-code”will be entered. This blocking cannot be disabled
using a remote control or VALET button.
1. Call the system number and wait for the answer.
2. Dial 666* to block an engine or 999* to unlock it (after dialing 999* you should enter the“Secret PIN
code”that is located on the owner’s card).
!All otheR commANds cAN be eNteRed IN the sAme mANNeR.
Changing settings via a phone
Disarm the system, call the system number, wait for the answer, switch on the ignition for 1-3 seconds
(but no more than 5 seconds), then switch it off. The system will enter the settings mode.
An example of changing the owner’s system number:
1.Enter the setting menu via a phone according to the instruction above;
2.Dial DTMF command 1*(phone number settings) and 1*(owner’s system number);
3.Enter new owner’s number in the format *XXXXXXXXXXX # (the system recognizes‘*’ as ‘+’);
4. To confirm, dial 1*.
!theRe ARe 3 WAys to chANGe mAIN oWNeR’sphoNe NumbeR:
1. vIA AphoNe, usING dtmf commANds settINGs mode.
2. usING RAdIo tAGs: tuRN oN the IGNItIoN WheN the system Is dIsARmed ANd cAll the system phoNe NumbeR. WAIt foR the
ANsWeR, dIAl the “Guest pIN-code” (defAult vAlue Is 1-2-3-4) If you ARe cAllING Not fRom the mAIN oWNeR’sNumbeR,
theN pRess ANd hold the buttoN oN the RAdIo tAG foR 2 secoNds (uNtIl the secoNd flAsh of the seNd INdIcAtoR).
ReleAse the buttoN, the system WIll RecoGNIze the INcomING phoNe NumbeR As the “mAIN oWNeR’sphoNe NumbeR.
3. usING the pANdoRA AlARm studIo oR pANdoRA bt ApplIcAtIoNs.

33
USER MANUAL
System’s number -> «#»
5
5
*
*
Set up date
Set up time
1
1
*
*
2
2
*
*
Phone
number settings
Owner's number -> #
Additional owner's number -> #
Second additional owner's
number -> #
Account balance inquiry number -> #
1
1
*
*
1
1
*
*
2
2
*
*
3
3
*
*
4
4
*
*
Automatic
engine start
settings
By time
Set up time for automatic start
By voltage
Set up voltage for automatic start
1
1
*
*
2
2
*
*
3
3
*
*
4
4
*
*
By temperature
Set up temperature for automatic
start
5
5
*
*
6
6
*
*
By period
Set up period for automatic start
7
7
*
*
8
8
*
*
6
6
*
*
Sensor
sensitivity settings
Settings of the warning level of the
shock sensor sensitivity
Settings of the alarm level of the
shock sensor sensitivity
Settings of the motion sensor
sensitivity
1
1
*
*
2
2
*
*
3
3
*
*
4
4
*
*
Settings of the tilt sensor sensitivity
Settings of the warning level of the
supplementary sensor sensitivity
5
5
*
*
Settings of the alarm level of the
supplementary sensor sensitivity
6
6
*
*
7
7
*
*
Settings
of the voice calls
Voice calls on alarm
Voice calls on triggering warning
level of the sensors
Voice calls on engine start
Voice calls on engine stop
1
1
*
*
2
2
*
*
3
3
*
*
4
4
*
*
Voice calls on restoring GSM
connection
Voice calls on disarming
5
5
*
*
6
6
*
*
Voice calls on entering
programming mode
Voice calls when radio relay
connection is lost
7
7
*
*
8
8
*
*
Voice calls when on-board voltage
is low
9
9
*
*
Voice calls on accident
0
0
*
*
2
2
*
*
Settings
of the text messages
Text messages on alarm
Text messages on triggering warning
level of the sensors
Text messages on engine start
Text messages on engine stop
Text messages on restoring GSM
connection
Text messages on disarming
1
1
*
*
2
2
*
*
3
3
*
*
4
4
*
*
5
5
*
*
6
6
*
*
Text messages on entering
programming mode
Text messages when radio relay
connection is lost
7
7
*
*
8
8
*
*
Text messages when on-board
voltage is low
9
9
*
*
Text messages on accident
0
0
*
*
3
3
*
*
Immobilizer
settings
Immobilizer (on/o)
Antihijack
1
1
*
*
2
2
*
*
4
4
*
*
Additional
settings
Changing guest PIN-code
Entering as guest
Remote blocking
1
1
*
*
2
2
*
*
3
3
*
*
Set threshold voltage for sending
text message
5
5
*
*
5
5
*
*
Settings
of saving mode
GSM connection
Money saving mode of the GSM
connection
Voice calls in roaming service
1
1
*
*
2
2
*
*
3
3
*
*
8
8
*
*
Current time
and date settings
9
9
*
*
NOTE: Engine start via temperature is available
only if temperature sensor is connected. The sensor
availability depends on the system set
ONLINE SERVICE AND MOBILE APPLICATION
Telemetric function of the system allows you to
control your vehicle using the online service pandora-
on.com or mobile apps – Pandora Connect.
The Pandora Connect applications can work via a
Bluetooth channel when there is no connection to the
server. To get these functions, the mobile phone must
be paired with the system.
!foR the coRRect opeRAtIoN of the Gsm fuNctIoNs, AN oWNeR
should moNItoR the stAtus/bAlANce of the sIm cARd INstAlled
IN the system. Ifthe sIm cARd Is blocked oR defectIve, Gsm
fuNctIoNs of the system WIll be uNAvAIlAble.
Before using the online-service, It is required to
create an account (Registration), login to your account
(using your email and password created on the
registration step) and add the system to your account
(enter information from the“Owner’s personal card”).
Registration
Visit the website or open the mobile app to create an
account.
Web-service:
https://pandora-on.com.
Mobile apps:
Pandora Connect for iOS is available in the AppStore;
Pandora Connect for Android is available on the Play
Market (Google Play).
!mINImum RequIRemeNts: ANdRIod v4.4; Ios v10
You will create the data to sign in: LOGIN – your email, PASSWORD – a password entered during the
registration.You will receive an email with a confirmation link. Click the link to complete the registration
procedure.
pandora-on.com
LOGIN
PASS
e-mail
********
LOGIN
PASS
e-mail
********

35
34 USER MANUALPANDORA CAMPER PRO V2
Login
After completing of the registration process, you can login to the online service via a computer’s web
browser or via the mobile apps Pandora Pro or Pandora Online. Use your previously created login/
password to login:
Adding a system to your account
The created account can support up to 3 telemetry systems. Use the information from the“Owner’s
personal card”to add the system to your account.
Go to the “Add a device/Add a system” window and enter the LOGIN and PASS from the “Owner’s
personal card”, create a name for your car and click “Add”.
!eRAse the pRotectIve lAyeR cARefully. doNot use ANy shARp objects to AvoId dAmAGING of hIddeN INfoRmAtIoN uNdeR
the pRotectIve lAyeR.
After this, you will be able to control, change setting and get information about the vehicle state
through the online-service.
!NumbeR of eveNts IN the hIstoRy Is lImIted. eveNts ARe stoRed foR At leAst oNe moNth.
Control via Bluetooth
The Pandora Pro and Pandora Online applications can work via a Bluetooth channel when there is
no connection to the server. This type of connection allows you to control the system, receive status
information and use your mobile phone as an authorization device.
To get access to these functions, pair a mobile device in the system:
I. ENTER THE PROGRAMMING MODE
Use the VALET button to enter the “Service PIN-code” (default value is 1-1-1-1). See the detailed
instruction of code entering in the “Control the system in case of emergency”section.
II. ENTER THE“PAIRING A MOBILE PHONE”PROGRAMMING LEVEL
After entering programming mode, press and hold the VALET button for 5 seconds (until the fifth
signal of the Siren/Beeper”). The system will enter the“Pairing a mobile phone”programming level. The
LED indicator will light green, the system is ready for pairing.
!the pRevIously pAIRed devIce WIll be eRAsed fRom the system memoRy AfteR eNteRING the level.
III. PAIR A MOBILE PHONE
Turn on Bluetooth on your mobile phone and open the mobile application. Go to : Settings -> Bluetooth
control -> Bluetooth device/ Not specified (Android)» -> + (iOS)/ Add (Android». Select the found system in
the search window, the system and the mobile device will be automatically paired. The system will confirm
pairing with the series of green and red flashes of the LED and a sound signal of the siren.
! IftheRe Is No AutomAtIc pAIRING, eNAble the “pIN Request foR phoNe
pAIRING”Item IN the “RAdIo tAG ANd mobIle devIce fuNctIoNs”sett INGs ANd mAke the pAIRING pRoceduRe AGAIN. A mobIle
devIce WIll Request ApIN-code (fActoRy pRe-set Is 0-0-1-1-1-1 WheRe 4 lAst dIGIts ARe the “seRvIce pIN-code”.
IV. EXIT PROGRAMMING MODE
Turn on the ignition and then turn off to exit programming mode.
!the system suppoRts oNly oNe mobIle devIce.

37
36 USER MANUALPANDORA CAMPER PRO V2
CONTROL THE SYSTEM
Arming
To arm the system when the ignition is off, use one of the methods described below. The system
will confirm the command with 1 short sound signal 1х and 1 flash of light signalization
1х .
Remote control
Shortly press the , button on the remote control when you are in the radio coverage zone. The
remote control will play “ARMING” ringtone and security mode status icon (the lock) will be changed
to .
To arm the system without a sound notification press and hold the button for more than 1
seconds.
Radio tag
A radio tag must be in the Bluetooth coverage area. Shortly press the control button , on the tag.
Slave mode
Shortly press the“Lock”button on an original remote control or use a sensor/button on a door handle
(for cars with an intelligent access system).
Phone
Call the system number. Wait for the answer. Dial the 1 * . command. To arm the system without siren
signals dial the 1 0 * .
doors locking
system arming
SLAVE
HANDS FREE
PANDORA BT
1x /1x
SLAVE
HANDS FREE
MOBILE APP
1 *
Online-service PRO.P-ON.RU
Login to the PANDORA-ON.COM, when the system is online (there is an Internet connection) press the
button on the control panel.
Mobile application Pandora Connect
Open the mobile application. When the system is online (there is an Internet or Bluetooth connection),
press and hold the button on the control panel until the scale is fully loaded.
HandsFree mode
Move with an authorization device away from your vehicle .
VALET button
Press and hold the VALET button for 3 seconds. The system will be armed in 30 seconds. The LED
indicator is lighting red during the countdown.
!theRe Is AN optIoN IN the system settINGs thAt AlloWs to ARm the system WIth dIsAbled seNsoRs (shock/tIlt/motIoN
ANd AddItIoNAl seNsoRs). the settING “sWItch off seNsoRs WheN ARmING usING vAlet butt oN” Is AvAIlAble IN the AlARm
studIo (“mAIN settINGs” -> “seNsoRs settINGs”).
Activating Stay Home mode
To activate Stay Home mode when the ignition is off, use one of the methods described below.
The system will confirm the command with 1 flash of light signalization .
Remote control
Press and hold the button on the remote control for 1 second (until a sound signal/flash of the
SEND/ALARM indicator) when you are in the radio coverage zone.The remote control will play“ARMING”
ringtone and security mode status icon (the lock) will be changed to .
Mobile application
Open the mobile application. When the system is online (there is an Internet or Bluetooth
connection), press and hold the button on the control panel until the scale is fully loaded. The
security mode status icon will be changed to .

39
38 USER MANUALPANDORA CAMPER PRO V2
Radio tag
A radio tag must be in the Bluetooth coverage area. Press and hold the control button on the tag
for 2 seconds (until the second flash of the «SEND» indicator).
Disarming
To disarm the system, use one of the methods described below. The system will confirm the
command with 2 short sound signals 2х and 2 flashes of turn indicators 2х .
Remote control
Press and hold the , button on the remote control when you are in the radio coverage zone. The
remote control will play“DISARMING” ringtone and security mode status icon (the lock) will be changed
to .
To disarm the system without sound confirmation press and hold the button for 1 second
or more.
Radio tag
Radio tag must be in the Bluetooth coverage area. Shortly press the control button on the tag.
Slave mode
Shortly press the “Unlock” button on an original remote control or use a sensor/button on a door handle
(for cars with an intelligent access system.
Phone
Call the system number. Wait for the answer. Dial the 0 * command. To disarm the system without siren
signals dial the 0 *0 command.
Online service
Login to the PANDORA-ON.COM, when the system is online (there is an Internet connection) press the
button on the control panel.
Mobile application Pandora Connect
Open the mobile application. When the system is online (there is an Internet or Bluetooth connection),
press and hold the button on the control panel until the scale is fully loaded.
HandsFree mode
Move toward the vehicle with an authorization device .
VALET button
Enter the ”Secret PIN-code”(see the ”Emergency disarming using the VALET button” section)
Locking/unlocking doors when ignition is on
The system allows you to lock and unlock doors when ignition is on. To do this, use one of the
methods described below.
Remote control
Press the button to lock doors or the button to unlock doors when you are in the radio
coverage zone.
Mobile application Pandora Connect
Open the mobile application. When the system is online (you are in the radio coverage area), press and
hold the button to lock doors or the button to unlock doors on the control panel until the scale
is fully loaded.
Automatic modes
There are automatic lock modes that will lock the doors at the car movement or on switching on the
ignition. When using doors locking mode on car movement start, the system will detect car moving
and perform doors locking (it depends on speed status in a digital CAN-bus or motion sensor sensitivity
settings). When using doors locking mode on switching on the ignition, the doors will be locked
automatically 5 seconds after the ignition was switched on. If any door was opened after the ignition
doors unlocking
system disarming
2x /2x
SLAVE
HANDS FREE
MOBILE APP
0 *