Pandora Camper User manual

Pandora would like to thank you for
choosing our security system Pandora Camper
Pandora Camper – is a telemetric service-security system built for motorhomes with on-board
voltage of 12V. It is a complex engineering solution, which includes unique and modern technological
software and hardware solutions.
When developing the system, we were using the most up-to-date electronics from world’s best
manufacturers. The device is built using high-precision mounting and control machinery, thus we
guarantee highest possible quality, reliability and stable technical characteristics for the whole
operation period.
Pandora Camper has a cryptographically strong authorization code with unique dialog algorithm
and individual 128 bit encryption key on every device. We guarantee 100% protection form electronic
hacking for the whole operation period.
The system is built for your convenience: it’s ergonomic, reliable and it has the highest security and
service characteristics, 3 years unconditional warranty and free service and support. We are happy to
provide any support we can – feel free to use our online support.
This device has limited external factors resistance. It should not be subjected to water beyond occasional splatter, or operated in
temperatures outside -40 to +85° C range. All system components must be installed only in a car interior. The base unit, remote control and
radio tags fulfil the IP40 category of protection against water.
Our web-site: pandorainfo.com
Customer support: [email protected]

3
2USER MANUALSECURITY-SERVICE SYSTEM PANDORA CAMPER
EN
Table of contents
General information 4
System set 5
System modules layout 6
Base unit of the system 7
Owner’s personal card 8
External VALET button 9
System functions and modes 11
Security mode 11
Security zones 11
Sound and light signalization 12
Stay Home mode 13
Slave mode 13
Owner authorization devices and functions 13
Checking the number of paired remote controls/radio tags/mobile device 15
Remote control D030 16
Switch on/off the remote control 17
LED indicator of the remote control signals 17
Charging the remote control 17
Updating firmware of the remote control 17
Icons of the remote control 18
Quick access functions of the remote control 19
Immobilizer radio tag BT760 20
Functions of the button 20
Replacing an immobilizer tag battery 21
Update firmware of a radio tag 21
Control the system from a phone 22
Changing settings via a phone 24
Online service and mobile apps 26
Events history 27
Mobile application Pandora Camper 27
Control the system 28
Arming 28
Activating Stay Home mode 29
Delayed arming 30
Disarming 30
Locking/unlocking doors when ignition is on 31
Car search function 32
PANIC mode 32
Service mode 33
Control the system in case of emergency 34
Emergency disarming 35
Emergency control of the anti-theft functions 36
Warranty obligations 37
Installation certificate 38
Acceptance certificate 39
Warranty card 39

5
4USER MANUALSECURITY-SERVICE SYSTEM PANDORA CAMPER
EN
System set
1. User manual and wiring diagram 1
2. Remote control D030 1
3. Radio tag BT760 1
4. Owner’s personal card 1
5. Base unit 1
6. External LED/VALET button 1
7. Beeper 1
8. Wireless door sensor DMS-100 BT 4
9. Siren PS-330 1
10. Main cable of the base unit 1
11. Additional cable of the base unit 1
12. External temperature sensor 1
13. Blocking relay 2
14. Magnetic reed sensor 2
15. Fastening kit 1
16. Packaging 1
! The manufacTurer reserves The righT To change The sysTem seT and consTrucTion of The producT To improve iTs
Technological and operaTional parameTers wiThouT noTificaTion.
Read the following section before using the system
Carefully read this manual before starting installation and using the security-service system. Pay
attention to text marked with !
!The sysTem is acomplex Technical producT. sysTem insTallaTion and configuraTion musT be carried ouT only by a
skilled professional.
!feaTures and sysTem modes, conTrol of The vehicles zones depends on The Type of connecTion and sysTem seTTings,
original vehicle operaTion logic and Trim.
! The sysTem seT includes an “owner’spersonal card”. This card conTains informaTion under aproTecTive layer ThaT
is inTended only for The owner of The sysTem. make sure ThaT The proTecTive layer on The owner’splasTic card is inTacT
afTer The insTallaTion of The sysTem.
!read The “owner’spersonal card”secTion of This manual before erasing The proTecTive layer.
! The sysTem has agsm inTerface. ask an insTaller who has insTalled The sysTem To check The gsm funcTions
operaTion using your phone:
• dial 500* command To requesT coordinaTes (see The “conTrol The sysTem from aphone” secTion).
• Trigger alarm when The sysTem is armed. The sysTem musT call your phone number (“main owner’sphone number”).
Toquickly change The “main owner’sphone number”, Turn on The igniTion when The sysTem is disarmed and call The
sysTem phone number. waiT for The answer, Then press and hold The buTTon on The radio Tag for 2 seconds (unTil The
second flash of The send indicaTor). release The buTTon, The sysTem will recognize The incoming phone number as
The “main owner’sphone number”.
• check The “guesT pin-code”(facTory defaulT value is 1-2-3-4). call The sysTem from an “addiTional phone number”
or from any oTher phone number unknown for The sysTem.
! The sysTem can work wiTh amobile applicaTion. iTis required To creaTe an accounT, add The sysTem To your accounT,
pair your mobile phone wiTh The sysTem. ask an insTaller To help you To configure The mobile applicaTion.
! when sysTem insTallaTion is finished:
• check ThaT The “insTallaTion cerTificaTe” and “warranTy card” are filled ouT. These documenTs may be required for
conTacTing The cusTomer supporT.
• check The sysTem operaTion and funcTions wiTh aspecialisT.
• werecommend ThaT you mark each working funcTion wiTh asign in The “conTrol The sysTem” secTion.
• ask an insTaller To mark The layouT of The sysTem componenTs on The diagram. This informaTion may be required for
diagnosTic/configuring or emergency deacTivaTion of The sysTem.
• werecommend ThaT you change The defaulT value of The “service pin-code” (1-1-1-1). ask an insTaller To change
The “service pin-code”.
wriTe down and remember a new value of The “service pin-code”
• werecommend ThaT you change The defaulT value of The “guesT pin-code” (1-2-3-4). (see The “changing seTTings
from aphone” secTion -> 5* addiTional seTTings -> 1* changing The guesT pin code.
wriTe down and remember a new value of The “guesT pin-code”
• ifThe “code immobilizer (pin-To-drive)” funcTion is implanTed:
wriTe down and remember The “immobilizer pin-code”
mark abuTTon (buTTon/lever/pedal) ThaT is used To enTer The “immobilizer pin-code” in The layouT diagram.

7
6USER MANUALSECURITY-SERVICE SYSTEM PANDORA CAMPER
EN
System modules layout
Base unit
Blocking relay (circuit
being blocked)
External VALET button
Sensor DMS-100 BT
1
2
3
4
5
6
7
8
9
10
Base unit of the system
Built-in GSM modem (GPRS/SMS/LBS-services)
A built in modem allows the system to work in a mobile network using an installed SIM card: voice
and SMS notifications, control from a phone using DTMF-commands, determination of coordinates
based on cellular base station location (only for 500* command), connection with our online-service
and mobile applications.
For the correct operation of the GSM functions, an owner should monitor the status/balance of the
SIM card installed in the system. If the SIM card is blocked or defective, GSM functions of the system will
be unavailable.
Built-in GPS/GLONASS-receiver
A built-in GPS/GLONASS-receiver is designed to determine current location and to automatically
determine date and time.
!ToauTomaTically deTermine daTa and Time, iT is required To seT correcT uTc Time zone using The mobile app or The
online-service.
2.4GHz radio channel, Bluetooth 5.0 protocol (BT5.0)
An integrated radio channel is used to connect the system with a mobile phone and additional
Bluetooth devices. The system supports up to 14 additional Bluetooth devices: 1 remote control D-030,
up to 3 radio tags, 1 mobile phone, up to 10 DMS-100BT sensors, up to 2 radio relays BTR-101, 1 RHM-
03BT module, 1 BT-01 relay or DI-04 module.
Digital protection AES (128 Bit)
Dialog coding of commands with a 128-bit encryption key guarantee secure communication via
the radio channel. The encryption key can be changed when you re-pair a remote control or additional
Bluetooth devices.
3D-accelerometer
A built-in accelerometer is used to detect shock/motion/tilt:
• 2 zones of the shock sensor (alarm/warning);
• Separate sensitivity adjustment by zones;
• Engine blocking on motion start;
• Central lock closing when start driving.

9
8USER MANUALSECURITY-SERVICE SYSTEM PANDORA CAMPER
EN
Multisystem digital 2CAN | LIN interface
Integrated digital CAN and LIN interfaces allow connection to digital buses of a vehicle for reading
information (statuses) and controlling vehicles (commands). The LIN-interface can be used to control
Webasto ThermoTopEvo and Eberspacher Hydronic/Hydronic2 heaters.
!see deTailed informaTion on loader.pandorainfo.com
icro-USB port
The system has a buil-in micro-USB port that is used for system configuration and update via the
Pandora Alarm Studio. The system can be power from the USB, so you can configure it before installation.
Temperature
The system can determine interior, engine and outside temperature.The following sources are used:
built-in temperature sensor, connector of an external temperature sensor, digital CAN-bus, values from
additional devices.
! defaulT values: inTerior TemperaTe – builT-in sensor; engine TemperaTure – exTernal sensor; ouTside TemperaTure
– can.
Synchronized clock of the baze unit
Built in clock is automatically synchronized with the built-in GPS/GLONASS receiver
! iTis required To seT correcT uTc Time zone using The mobile app or The online-service.
Owner’s personal card
! erase The proTecTive layer carefully. donoT use any sharp
objecTs To avoid damaging of hidden informaTion under The
proTecTive layer. The informaTion is inTended only for The owner.
The card and The hidden informaTion cannoT be resTored.
The owner’s personal card contains private information
under a protective layer:
• PIN (the «Secret PIN-code”) is a 4-digit number. This
code can be used to disarm the system and to deactivate
immobilizer functions. It can be also used to enter programming mode. This information cannot be
changed or restored
• LOGIN – is a 10-digit number. This information is used to add the system to the online service and
mobile applications. This information cannot be changed or restored
• PASS – contains 8 characters and can consist of digits, lower and upper case letters. This information
is used to add the module to the online service and mobile applications. This information cannot be
changed or restored.
• Phone number is a phone number of the SIM-card supplied with the system. This number is not used
if you change the SIM-card.
External VALET button
An external VALET button with a three-color status
LED indicator is placed inside a vehicle (see the system
modules layout). The button is used for programing
the system, arming/disarming, activating/deactivating
dimmobilizer mode.
!original vehicle conTrols (buTTons/levers/pedals) can be used
as The valeT buTTon. see The deTailed informaTion on loader.pandorainfo.com.
LED INDICATOR
VALET BUTTON
2-2-2-2
PIN

11
10 USER MANUALSECURITY-SERVICE SYSTEM PANDORA CAMPER
EN
LED indicator signals
INDICATOR STATUS DESCRIPTION
THE SYSTEM IS ARMED
Short red ashes System is armed
Short green ashes System is armed
(a radio tag is in the coverage zone)
Fast red ashes Alarm
THE SYSTEM IS DISARMED
Faded System is disarmed
Red System is preparing for automatic or delayed arming
Green
(when ignition is on) System is in service mode
Orange ashes
(when turning on the ignition) Conrms the number of paired remote controls
Green ashes
(when switching on the ignition) Conrms the number of paired radio tags
Red ash
(when switching on the ignition) Conrms a paired mobile device
WHEN ENTERING THE“SECRET PIN-CODE” OR THE“SERVICE PIN-CODE”
Orange ash Conrms a VALET button press
Conrms a paired mobile device Conrms a digit input
Red and green ashes Conrms correct PIN code
Long red ash PIN-code is incorrect
SYSTEM FUNCTIONS AND MODES
Security mode (the system is armed)
The system confirms arming with 1х sound and 1х light signals. When the system is armed, the
system monitors security zones with separated warning and alarm level of triggering:
• Warning mode – this mode activates when there is a slight impact on the shock sensor or additional
senor. It is accompanied with 1х light and 3х sound signals.
• Alarm mode - this mode activates when a sensor or one of the security zones is triggered. It
is accompanied with 30 sec. light and 30 sec. sound signals. The alarm signals can be
canceled by an arming or disarming command.
If one of the security zones is triggered the system:
• records this event in its non-volatile memory;
• activates the alarm or warning mode;
• informs an owner by all available means;
• blocks the engine (in accordance with the settings and connections).
If one of the security zones is opened at the moment of arming, the system will produce 4х
sound and 4х light warning signals.
If one of the security zones fails, the system will forcibly turn off this zone. If a switch triggers
more than 9 times in a row, it will be disabled until the next arming. The shock/tilt/motion sensor is
temporarily deactivated (15 sec.) if it has been triggered more than 3 times in a row.
The system confirms disarming with 2х sound and 2х light signals. The system deactivate
engine blocking (if the immobilizer function and additional blocking are not used). If there were alarm
events during the armed period, the system will produce 4х sound and 4х light warning
signals. The system continues to display all zones when it is disarmed, but the information is not saved
in the memory.
Security zones
• Interior temperature (status)
• Engine temperature (status)
• Outside sensor (status)
• Voltage of the on-board circuits (status)
• Engine operation control - RPM (status)
• Heater operating control (status)

13
12 USER MANUALSECURITY-SERVICE SYSTEM PANDORA CAMPER
EN
• Fuel level (status)
• Parking (automatic gearbox) /Handbrake (manual gearbox) status
• “Parking light is not turned off” notification (status)
• Shock sensor (security zone – alarm and warning level)
• Motion sensor (security zone – alarm level)
• Tilt sensor (security zone – alarm level)
• OE alarm system status via CAN, additional sensor (status, security zone – alarm and warning level)
• Turning ignition on (status, security zone – alarm level)
• Opening doors (status, security zone – alarm level)
• Opening a trunk (status, security zone – alarm level)
• Opening a hood (status, security zone – alarm level)
• Pressing brake (status, security zone – alarm level)
Sound and light signalization
DESCRIPTION STATE
(sound/light)
Arming 1х /1х
Disarming 2х /2х
Car search 5х /5х
Alarm, PANIC mode 30sec. /30sec.
Warning level of a sensor is triggerd 3х /1х
‘Sensors were triggered’signal when disarming /
Parking light is not turned o notication /
‘Sensors are triggered”signal when arming
4х /4х
Engine blocking warning in Anti-Hi-Jack mode 30sec. /30sec.
Stay Home mode
This mode is used to control the outer perimeter of a vehicle during parking when passengers are inside
the vehicle. This mode allows the system to protect your vehicle against intrusion through the parts of
the vehicle that can be open.
• The system will be armed silently when you activate the “Stay Home” mode, it will be confirmed
with 1х light signal. The system controls vehicle security zones and an additional gas sensor (it is
not included in the set) in this mode, built-in sensors (shock/tilt/motion) are disabled in this mode.
• The system will be disarmed when you deactivate the “Stay Home” mode, it will be confirmed with
2х sound and 1х light signals.
Slave mode
This mode allows arming and disarming using original vehicle control – an original key, button/sensor
of a keyless access entry system.
Slave mode can be implemented using analog connections or a digital protocol of a vehicle.
!This mode is enabled by defaulT for adigiTal proTocol. more informaTion on loader.pandorainfo.com. iTis
recommended To acTivaTe The “prohibiT disarming when aTag is absenT” To increase securiTy feaTures of The slave
mode. ifThis mode is acTivaTed, iT will be possible To disarm The sysTem only when aTag is in The coverage zone or using
The “secreT pin-code”.
Owner authorization devices and functions
Authorization devices
Authorization devices are Bluetooth-devices used to recognize an owner in the radio coverage zone
of the base unit. These devices allow implementing security and anti-hijack functions. You can use a
mobile phone, a radio tag BT-760 or a remote control D030 as an authorization device.
Alerts when using authorization devices
It is recommended to use an additional sound emitter Beeper when you use authorization devices.

15
14 USER MANUALSECURITY-SERVICE SYSTEM PANDORA CAMPER
EN
BEEPER SOUND SIGNALS
SIGNAL NAME DESCRIPTION
Activating service mode 1 sound signal
Deactivating service mode 2 sound signal
Correct input of the“Immobilizer PIN-code” 1 sound signal
A battery in a radio tag is discharged 3 sound signals /3 times
Absence of a radio tag 4 sound signals /4 times
Blocking warning Fast sound signals
Hands Free mode
This mode is used for automatic arming/disarming when an owner with an authorization device is
distancing or approaching a vehicle.
!This mode is disabled by defaulT. iTis required To make addiTional seTTings using The mobile applicaTion or pandora
alarm sTudio To use This mode. quick access commands To manage handsfree mode: 223* - acTivaTe handsfree
arming, 224* - acTivaTe handsfree disarming, 222* - deacTivaTe all handsfree modes.
Immobilizer mode
This mode is used to recognize an owner using authorization devices when the system is disarmed.
When turning on the ignition, the base unit performs a search for authorization devices in the radio
coverage zone. If there is no any authorization device in the radio coverage zone:
• If engine blocking is implemented – the system will block the engine. Engine blocking will occur
immediately or at the time a motion sensor detects movement, it depends on the system settings;
• If OBD connector blocking is implemented – the system will stay the connector blocked.
When an authorization device appears in the coverage zone, the system will exit blocking mode and
will continue to work in normal mode.
!This mode is enabled by defaulT. iTis required To make addiTional connecTions for This mode.
ANTI-HI-JACK-1/2 modes
The Anti-HiJack modes help to prevent aggressive seizure of a vehicle when authorization in case of
disappearance of authorization devices from the radio coverage zone when system is disarmed.
ANTI-HI-JACK-1 mode – The base unit checks if an authorization device is in the radio coverage zone
each time when ignition is on and a door is opened/closed.
ANTI-HI-JACK-2 mode – The base unit constantly checks if an authorization device is in the radio
coverage zone when ignition is on.
If the system cannot detect an authorization device, the base unit will perform a delayed engine
blocking. The siren will play the ‘Engine blocking warning’ ringtone before blocking. The engine will
be blocked immediately or at the time the car starts moving, it depends on system settings. When an
authorization device appears in the coverage zone, the system will exit blocking mode and will continue
to work in normal mode.
!This mode is disabled by defaulT. iTis required To make addiTional seTTings and connecTions for This mode.
Multi-button code immobilizer (pin-to-drive)
Multi-button code immobilizer (pin-to-drive) is a function that allows disarming, disabling blocking and
controlling service mode and time channels using original vehicle controls (button, lever or pedal) and
a pre-programmed PIN-code (the “Immobilizer PIN-code”).
AN EXAMPLE OF USING THE FUNCTION
• Turn on the ignition to disable engine blocking or enable service mode, turning on the ignition is not
required if you want to disarm the system or control time channels.
• Enter the “Immobilizer PIN-code”. Press a programmed button/lever/pedal the number of times
equals to the first digit. Pauses between presses should not exceed 1 second. More than 1 second
pause will be interpreted as the start of the next digit input. The immobilizer code can consist max
of 4 digits from 1 to 9.
• The system will confirm the correct input by a sound signal of the beeper and a programmed
function will be performed.
!This mode is disabled by defaulT. iTis required To make addiTional seTTings and connecTions for This mode.
Checking the number of paired remote controls/radio tags/mobile device
The number of paired remote controls/radio tags/mobile device can be checked by the number of
flashes of the LED indicator. The number of paired remote controls/tags/mobile device can be checked
when switching on the ignition (the system must be disarmed). The number of orange flashes will
indicate the number of paired remote controls, the number of green flashes will indicate the number of
paired radio tags, a following red flash will indicate a paired mobile device.
You can also check the number of paired remote controls/radio tags/mobile device by taking off
and putting back on battery terminal. The system will emit short sound signals from a siren .
• First series of the siren signals indicates the number of paired radio tags
• The second long signal after a pause of 2 seconds indicates a paired mobile devices.

17
16 USER MANUALSECURITY-SERVICE SYSTEM PANDORA CAMPER
EN
REMOTE CONTROLD030
A remote control is a device used to control and monitor vehicle/system state. The remote control is
also used as an authorization device for “Immobilizer/Anti-Hijack/HandsFree” modes. It works in the
Bluetooth coverage zone. Each event is displayed as an icon on the OLED-display and is accompanied
with a sound and vibro indication.
! all conTrol commands are TransmiTTed via radio channel, for maximum effecTiveness and range iT is recommended
noT To shield aerial area (see picTure) wiTh fingers when using aremoTe conTrol.
• OLED – display
• 3 control buttons
• Built-in sound indicator (16 ringtones)
• Built-in vibro indicator
• Built-in LED SEND/ALARM indicator
• 2,4 GHz radio interface (Bluetooth protocol)
• Dialog coding of commands (AES-128 encryption)
• Built-in battery
• Built-in micro-USB port
OLED
micro-USB
SEND/ALARM
Switch on/o the remote control
Press and hold the button for 3 seconds to switch on/off the remote control.
LED indicator of the remote control signals
RED indicator“ALARM” Green indicator“SEND”
Flashes frequently if there is any notication Flashes if there is a connection with the base unit
Flashes occasionally when there is no connection Goes dark when there is no connection with the base
unit
Charging the remote control
There is an indication of the battery charge level . on the display. Charge the battery if the
remote control does not turn on or the charge level indicator displays the last segment . The battery
is charged using a standard micro-USB cable.
Updating rmware of the remote control
• Download the Pandora BT application (for Android or iOS devices equipped with a Bluetooth 4.0 Low
Energy or higher module).
• Press and hold the button. Connect the micro-USB cable to the remote control whule holding the
button. Release the button after the connection.
• Open the mobile app and find the remote control, select the device and select one of the update
option: FILE MANAGER – firmware will be uploaded from the phone storage (only for Android).
INTERNET – firmware will be uploaded by an internet connection.

19
18 USER MANUALSECURITY-SERVICE SYSTEM PANDORA CAMPER
EN
Icons of the remote control
Additional sensor/
OE alarm status
Security zone
(alarm level)
Additional sensor/
OE alarm status
Security zone
(warning level)
Tilt sensor
Security zone
Motion sensor
Security zone
Ignition
Security zone
Doors security zone
Trunk security zone
Low voltage security zone
Brake pedal security zone
Heater operation icon
Connected to the base unit
Security mode status
Current time
Battery charge level
Engine temperature
Interior temperature
Outside temperature
Vehicle battery voltage
Fuel level
Shock sensor Security zone
(Warning level)
Shock sensor Security sensor
(alarm level)
12 48
90
°
22
°
-18 С
°
55
P
1
2
.
0
V
Quick access functions of the remote control
System is disarmed System is armed
(no alarm events)
Ignition is on Ignition is o
(short press) Lock doors without
arming Arming with sound confrmation Search mode – flashes of turn signals with sound signals for 5
seconds
(1 sec.) Activate “Stay Home”
mode Search mode – flashes of turn signals with sound signals for 5
seconds
(short press) Unlock doors Unlock doors Disarming with sound
conrmation
(1 sec.) Disarming without sound
conrmation
(short press) Switch on the display
(1 sec.) Open side door
(2 sec.) Switch on/o time channel
(3 sec.) Switch on/o the remote control
+
(short press)
PANIC mode
+
(short press)
Arming when the engine
is running with sound
conrmation
Arming in 30 seconds
With sound notication
+ (1 sec.) Arming when the engine
is running with sound
conrmation
Arming in 30 seconds
without sound
notication

21
20 USER MANUALSECURITY-SERVICE SYSTEM PANDORA CAMPER
EN
RADIO TAG BT760
Aradio tag isa device usedto controla vehicle/system.The remote control is alsoused as an authorization
device for“Immobilizer/Anti-Hijack/HandsFree” modes. It works in the Bluetooth coverage zone.
A radio tag has: a control button for arming/disarming and activating/deactivating service mode;
a built-in accelerometer allows the tag to go into energy saving mode when there is no movement; a
LED indicator SEND.
• Control button for arming/disarming and activating/
deactivating service mode
• LED indicator SEND
• Bluetooth protocol
• Built-in accelerometer
• CR 2032 Battery
• 2,4 GHz radio interface (dialog encryption AES-128)
Light indication of the SEND indicator when there is a
short press of the button
• No flashes – a battery is discharged
• 1 flash – radio tag operation is correct
Light indication of the SEND indicator when installing a
battery
• No flashes – a battery is discharged
• 1 flash – low battery level
• flashes – high battery level
!avoid moisTure on The radio Tag. donoT place The radio Tag near magneTs or producTs wiTh self-magneTic fields.
Functions of the button
ACTION FUNCTION
Short press when ignition is o Arm/disarm
Press and hold for 2 sec when the
system is disarmed and ignition is o Activate Stay Home
SEND
Open here
Press and hold for 2 sec when the
system is disarmed and ignition is on Change the“Main owner’s phone number”
Press and hold for 2 sec when ignition
is on Activate/deactivate Service mode
Press and hold for 6 sec. Pair a tag with the base unit
Press and hold for10 sec. Firmware update
Replacing an immobilizer tag battery
Carefully open the cover of the tag’s battery compartment. Extract discharged battery and insert a
new one keeping in mind the correct polarity. Replacing a battery will not cause a loss of tag code
information, as authorization data is stored in the non-volatile memory of the MCU. Carefully close the
cover of the tag’s battery compartment. All elements of construction should be rigidly locked in places.
If it is so, the tag can be operated as usually.
Update rmware of a radio tag
• Download the Pandora BT application (for
Android or iOS devices equipped with a
Bluetooth 4.0 Low Energy or higher module)
• Open the mobile app Pandora BT.
• Press and hold the button of the radio
tag until the 10th flash of the «SEND», indicator,
then release the button.
• Select the found device and select one of the
update option: FILE MANAGER – firmware will
be uploaded from the phone storage (only for
Android). INTERNET – firmware will be uploaded
by an internet connection.

23
22 USER MANUALSECURITY-SERVICE SYSTEM PANDORA CAMPER
EN
CONTROL THE SYSTEM FROM A PHONE
!for The correcT operaTion of The gsm funcTions, an owner should moniTor The sTaTus/balance of The sim card
insTalled in The sysTem. ifThe sim card is blocked or defecTive, gsm funcTions of The sysTem will be unavailable.
Call the system’s phone number. When it answers, enter a command code
* iTis required To enTer The “secreT pin-code” afTer dialing acommand
Activate/Deactivate service mode
1. Call the system number. Wait for the answer.
2. Turn on the ignition, an authorization device (a radio tag, a remote control, a paired mobile phone
with the app installed) must be in the coverage zone, enter the “Immobilizer PIN-code” (if the “Code
immobilizer” function is enabled).
3. To activate service mode, dial the 551* DTMF command — “Activate service mode”, then enter the
“Secret PIN-code”from the owner’s personal card.
4. To deactivate service mode, dial the 552* DTMF command —“Deactivate service mode”.
Voice help
The system has a voice help menu. During a voice call to the system, dial 9* and listen to the information
about system control commands.
#
#
9
9*
*
*
*
9
9
0
0*
*
1
10 00 0*
*
Repeat the last message
Silent arming
0
0
0
0*
*
0
0
1
1*
*
Silent disarming
Help
1
1*
*Arming
0
0*
*Disarming
Events history
5
5
1
1*
*Tow truck mode
Request GSM account balance
3
33 33 3*
*Switch on add. CAN function
5
50 00 0*
*
4
45 56 6*
*
6
65 54 4
*
*
2
25 58 8*
*
Request current coordinates
Switch on additional channel
Switch o additional channel
1
15 56 6*
*
6
65 51 1*
*
Switch on heater
Switch o heater
6
66 66 6*
*
9
99 99 9*
*
Activate engine blocking
Deactivate engine blocking*
9
99 98 8*
*
8
88 88 8*
*
Deactivate authorization devices*
Activate authorization devices
2
22 22 2*
*Disable HandsFree
2
22 23 3*
*Enable HandsFree arming
2
22 24 4*
*Enable HandsFree disarming
2
29 97 7*
*End a call
5
55 51 1*
*Activate service mode (see description below)*
5
55 52 2*
*Deactivate service mode
To end the session, hang up the phone.
Repeat the last message
To repeat any message, press * during a voice call to the system.
Arming/Disarming
1. Call the system number. Wait for the answer.
2. Dial 1* to arm, and 0* to disarm.
For silent arming dial 10* or 00*for silent disarming
3. The system will confirm arming/disarming. To end the session, hang up the phone.
Request current coordinates
1. Call the system number. Wait for the answer.
2. Dial 500*.
3. The system will confirm:‘Current coordinate sent via text message’and will send text message
with coordinates and a web link to a map to your phone.
To end the session, hang up the phone.
Request GSM account balance
1. Call the system number. Wait for the answer.
2. Dial 100*.
3. The system will confirm:‘Balance information sent via text message’and will send text message
with account balance information to your phone.
To end the session, hang up the phone.
Tow truck mode
This mode is intended for car transportation with preservation of arming function. Tow truck mode
can be activated only when the system is armed, it will be deactivated automatically when disarming.
1. Call the system number. If the system is in PANIC mode, receive an emergency call.Wait for the answer.
2. Dial 15* , to enable the “Tow truck” mode, the system will disable motion, shock and tilt sensors. To
end the session, hung up the phone.
3. To disable this mode, disarm the system.
Activating/Deactivating engine blocking
You can block a car engine using any phone. The engine will remain blocked
until phone command‘Unlock engine’will be sent and the “Secret PIN-code”will be
entered. This blocking cannot be disabled using a remote control or VALET button.

25
24 USER MANUALSECURITY-SERVICE SYSTEM PANDORA CAMPER
EN
1. Call the system number and wait for the answer.
2. Dial 666* to block an engine or 999* to unlock it (after dialing 999* you should enter the“Secret PIN-
code”that is located on the owner’s card).
!all oTher sysTem commands can be enTered in The same manner.
Changing settings via a phone
Enter the settings mode
Disarm the system, call the system number, wait for the answer, switch on the ignition for 1-3 seconds,
then switch it off. The system will enter the settings mode.
Example of changing the owner’s system number:
1. Enter the setting menu via a phone according to the instruction above;
2. Dial DTMF command 1*(phone number settings) and 1*(owner’s system number);
3. Enter new owner’s number in the format *XXXXXXXXXXX # (the system recognizes‘*’ as‘+’);
To confirm, dial 1*.
!There are 3 ways To change main owner’sphone number:
1. via aphone, using dTmf commands seTTings mode.
2. using radio Tags: Turn on The igniTion when The sysTem is disarmed and call The sysTem phone number. waiT for
The answer, Then press and hold The buTTon on The radio Tag for 2 seconds (unTil The second flash of The send
indicaTor). release The buTTon, The sysTem will recognize The incoming phone number as The “main owner’sphone
number.
3. using The pandora alarm sTudio applicaTions.
System’s number -> «#»
5
5*
*
Set up date
Set up time
1
1*
*
2
2*
*
Phone
number settings
Owner's number -> #
Additional owner's number -> #
Second additional owner's
number -> #
Account balance inquiry number -> #
1
1
*
*
1
1*
*
2
2*
*
3
3*
*
4
4*
*
Sensor
sensitivity settings
Settings of the warning level of the
shock sensor sensitivity
Settings of the alarm level of the
shock sensor sensitivity
Settings of the motion sensor
sensitivity
1
1*
*
2
2*
*
3
3*
*
4
4*
*Settings of the tilt sensor sensitivity
Settings of the warning level of the
supplementary sensor sensitivity
5
5*
*
Settings of the alarm level of the
supplementary sensor sensitivity
6
6*
*
7
7*
*
Settings
of the voice calls
Voice calls on alarm
Voice calls on triggering warning
level of the sensors
Voice calls on engine start
Voice calls on engine stop
1
1*
*
2
2*
*
3
3*
*
4
4*
*
Voice calls on restoring GSM
connection
Voice calls on disarming
5
5*
*
6
6*
*
Voice calls on entering
programming mode
Voice calls when radio relay
connection is lost
7
7*
*
8
8*
*
Voice calls when on-board voltage
is low
9
9*
*
Voice calls on accident
0
0*
*
2
2*
*
Settings
of the text messages
Text messages on alarm
Text messages on triggering warning
level of the sensors
Text messages on engine start
Text messages on engine stop
Text messages on restoring GSM
connection
Text messages on disarming
1
1*
*
2
2*
*
3
3*
*
4
4*
*
5
5*
*
6
6*
*
Text messages on entering
programming mode
Text messages when radio relay
connection is lost
7
7*
*
8
8*
*
Text messages when on-board
voltage is low
9
9*
*
Text messages on accident
0
0
*
*
3
3*
*
Additional
settings
Changing guest PIN-code
Entering as guest
1
1*
*
2
2*
*
Set threshold voltage for sending
text message
5
5*
*
5
5
*
*
Settings
of saving mode
GSM connection
Money saving mode of the GSM
connection
Voice calls in roaming service
1
1*
*
2
2*
*
3
3*
*
8
8*
*
Current time
and date settings
9
9*
*

27
26 USER MANUALSECURITY-SERVICE SYSTEM PANDORA CAMPER
EN
ONLINE SERVICE PANDORAON.COM AND MOBILE APPLICATION
PANDORA CAMPER
!for The correcT operaTion of The gsm funcTions, an
owner should moniTor The sTaTus/balance of The sim
card insTalled in The sysTem. ifThe sim card is blocked
or defecTive, gsm funcTions of The sysTem will be
unavailable.
It is required to create an account, add the
system to your account, pair your mobile phone
with the system. Registration is performed in the
mobile application or on the web-site.
Registration
Visit pandora-on.com website and register following
the instructions.
System login
After completing of the registration process, you
can login- to the online service via a computer’s web
browser or via special mobile app Pandora Camper
for the Android and iOS. Use your previously created login/password to enter the web site or mobile
app.
Adding a system to the online service
The Internet service pandora-on.com can support simultaneously several telemetry systems, installed
on various cars (private car park).
To add a telemetry system (vehicle) to the service, press ‘Add car’ button and go through the process
of adding, following the instructions. To add a car, individual owner’s card with registration information is
needed (shipped with the system).
!erase The proTecTive layer carefully. donoT use any sharp objecTs To avoid damaging of hidden informaTion under
The proTecTive layer.
pandora-on.com
LOGIN
PASS
@E-MAIL
********
LOGIN
PASS
@E-MAIL
********
Pandora Camper
Events history
Event history holds more than 100 different types of events that can happen to the system. Every event
is saved with date, time, coordinates and status of all control zones at the time the event has occurred.
The number of events in the history is limited. Storage of event history life is no less than 1 month.
Mobile application Pandora Camper
You can download the free app Pandora Camper from the App Store for iOS and Google Play for Android
devices. To access the app, use the login data received from the service at the registration stage.
Control via a radio channel
Mobile application Pandora Camper can control the system, receive status information and open
advanced settings without Internet connection when a phone is in the Bluetooth coverage zone.
To get access to these functions, pair a mobile device in the system.
Pairing a mobile device
To pair a mobile phone with the system:
I. ENTER PROGRAMMING MODE
Use the VALET button to enter the “Service PIN-code” (default value is 1-1-1-1). See the deatailed
instruction of code entering in the“Control the system in case of emergency” section.
II. ENTER THE “PAIRING A MOBILE PHONE”PROGRAMMING LEVEL
After entering programming mode, press and hold the VALET button for 5 seconds (until the fifth
signal of the Siren/Beeper”). The system will enter the“Pairing a mobile phone” programming level. The
LED indicator will light green, the system is ready for pairing.
III. PAIR A MOBILE PHONE
Turn on Bluetooth on your mobile phone and open the mobile application. Go to the “Search
device”screen: “My systems” -> “Add a bluetooth device”. The application will search for the system via
a Bluetooth connection.
Select the found system, the system and the mobile device will be automatically paired. The system
will confirm pairing with the series of green and red flashes of the LED and a sound signal of the siren.
IV. EXIT PROGRAMMING MODE
Turn on the ignition and then turn off to exit programming mode.
!The sysTem supporTs only one mobile device. ifThere is no auTomaTic pairing, enable The “pin requesT for phone
pairing” iTem in The “radio Tag and mobile device funcTions” seTTings and make The pairing procedure again. a mobile
device will requesT apin-code (facTory pre-seT is 0-0-1-1-1-1 where 4 lasT digiTs are The “service pin-code”.

29
28 USER MANUALSECURITY-SERVICE SYSTEM PANDORA CAMPER
EN
CONTROL THE SYSTEM
Arming
To arm the system when the ignition is off, use one of the methods described below. The system
will confirm the command with 1 short sound signal and 1 flash of light signalization .
Remote control
Shortly press the , button on the remote control when you are in the radio coverage zone. The
remote control will play “ARMING” ringtone and security mode status icon (the lock) will be changed
to .
Radio tag
A radio tag must be in the Bluetooth coverage area. Shortly press the control button on the tag.
Slave mode
Shortly press the “Lock” button on an original remote control or use a sensor/button on a door handle
(for cars with an intelligent access system).
Phone
Call the system number. Wait for the answer. Dial the 1 * . command.
To arm the system without siren signals dial the 1 0 * command.
Online-service
Login to the PANDORA-ON.COM, when the system is online (there is an Internet connection) press the
on the control panel.
doors locking
system arming
SLAVE
HANDS FREE
PANDORA BT
1x /1x
SLAVE
HANDS FREE
MOBILE APP
1 *
Mobile application
Open the mobile application. When the system is online (there is an Internet or Bluetooth connection),
press and hold the button on the control panel until the scale is fully loaded.
HandsFree mode
Move with an authorization device away from your vehicle .
VALET button
Press and hold the VALET button for 3 seconds. The system will be armed in 30 seconds. The LED
indicator is lighting red during the countdown.
!There is an opTion in The sysTem seTTings ThaT allows To arm The sysTem wiTh disabled sensors (shock/TilT/moTion
and addiTional sensors). The seTTing “swiTch off sensors when arming using val eT buTTon” is available in The
alarmsTudio (“main seTTings” -> “sensors seTTings”).
Activating Stay Home mode
To activate Stay Home mode when the ignition is off, use one of the methods described below.
The system will confirm the command with 1 flash of light signalization .
Remote control
Press and hold the button on the remote control for 1 second (until a sound signal/flash of the
SEND/ALARM indicator) when you are in the radio coverage zone.The remote control will play“ARMING”
ringtone and security mode status icon (the lock) will be changed to .
Mobile application
Open the mobile application. When the system is online (there is an Internet or Bluetooth
connection), press and hold the button on the control panel until the scale is fully loaded. The
security mode status icon will be changed to .
Radio tag
A radio tag must be in the Bluetooth coverage area. Press and hold the control button on the
tag for 2 seconds (until the second flash of the «SEND» indicator).

31
30 USER MANUALSECURITY-SERVICE SYSTEM PANDORA CAMPER
EN
doors unlocking
system disarming
2x /2x
SLAVE
HANDS FREE
MOBILE APP
0 *
Delayed arming
If when leaving the car you cannot arm it using a remote control (you have your hands full), you can use
delayed arming. To activate this mode, shortly press the and buttons simultaneously. The LED
indicator will turn red, the system will lock doors and will arm in 30 seconds, the siren will sound and turn
signals will flash once, indicating that the mode is triggered.
To activate this mode without sound confirmation, press and hold both and buttons for 1 second
until a sound and vibration signal.
To cancel delayed arming when it is triggered, simply press the button.
Disarming
To disarm the system, use one of the methods described below. The system will confirm the
command with 2 short sound signals and 2 flashes of turn indicators .
Remote control
Shortly press the , button on the remote control when you are in the radio coverage zone. The
remote control will play“DISARMING”ringtone and security mode status icon (the lock) will be changed
to .
To disarm the system without sound confirmation press and hold the button for 1 second or more.
Radio tag
A radio tag must be in the Bluetooth coverage area. Shortly press the control button on the tag .
Slave mode
Shortly press the“Unlock”button on an original remote control or use a sensor/button on a door handle
(for cars with an intelligent access system).
Phone
Call the system number. Wait for the answer. Dial the 0 * command.
To disarm the system without siren signals dial the 0 *0 command.
Online service
Login to the PANDORA-ON.COM, when the system is online (there is an Internet connection) press the
on the control panel.
Mobile application
Open the mobile application. When the system is online (there is an Internet or Bluetooth connection),
press and hold the button on the control panel until the scale is fully loaded.
HandsFree mode
Move toward the vehicle with an authorization device .
VALET button
Enter the ”Secret PIN-code”(see the ”Emergency disarming using the VALET button”section).
Locking/unlocking doors when ignition is on
The system allows you to lock and unlock doors when ignition is on. To do this, use one of the
methods described below.
Remote control
Press the button to lock doors or the button to unlock doors when you are in the radio
coverage zone.
Mobile application
Open the mobile application. When the system is online (you are in the radio coverage area), press and
hold the button to lock doors or the button to unlock doors on the control panel until the scale
is fully loaded.

33
32 USER MANUALSECURITY-SERVICE SYSTEM PANDORA CAMPER
EN
Automatic modes
There are automatic lock modes that will lock the doors at the car movement or on switching on the
ignition. When using doors locking mode on car movement start, the system will detect car moving
and perform doors locking (it depends on speed status in a digital CAN-bus or motion sensor sensitivity
settings). When using doors locking mode on switching on the ignition, the doors will be locked
automatically 5 seconds after the ignition was switched on. If any door was opened after the ignition
had been switched on, automatic locking will be disabled to prevent locking the keys inside the car.
Doors can be automatically unlocked when the ignition is switched off.
!These modes are disabled by defaulT, use The pandora alarm sTudio To enable These seTTings.
Car search function
To easily find your vehicle on a massive parking, shortly press the button when the car is armed. The
system will sound the siren and flash turn signals 5 times in a row.To use this function without
sound signals press and hold the button for 1 second.
PANIC mode
If your car or you are in danger and you want to draw attention to your car, you can use PANIC mode. In
this mode the siren will sound and turn signals will flash repeatedly for 30 seconds.
To activate this mode, use one of the methods described below.
Remote control
To activate the PANIC mode, press the and buttons simultaneously. To switch it off, press either
or button.
Mobile application
Open the mobile application. When the system is online (there is an Internet or Bluetooth connection),
press and hold the button on the control panel until the scale is fully loaded.To switch this function
off press and hold the button on the control panel until the scale is fully loaded.
Service mode
It is recommended to put the system into the service mode before handing it to a car service or valet
parking. When this mode is switched on, security system stops interfering with built-in electronics and
disables all functions to ease maintenance.
To switch on this mode, disarm the system, turn on the ignition, an authorization device (a radio
tag, a remote control, a mobile phone) must be in the coverage zone, enter the “Immobilizer PIN-
code”(if the“Code immobilizer” function is used) and use one of the method described below:
Radio tag
To activate/deactivate service mode, press and hold the button on a radio tag for 3 seconds
(until the third flash of the LED), release the button.
Phone
Call the system number wait for the answer.
• To activate service mode, dial the 155 * DTMF command and then dial the“Secret PIN-code”
from the Owner’s personal card.
• To deactivate service mode dial the
255 *
DTMF command.
•
Mobile application
To activate/deactivate service mode, open the mobile application. When the system is online (there
is an Internet or Bluetooth connection), press and hold the button on the control panel until
the scale is fully loaded.
!Tochange buTTons layouT or add new buTTons on The conTrol panel, go To “seTTings conTrol buTTons“.
Immobilizer buttons
• To activate service mode, enter the “Immobilizer PIN-code” and press the immobilizer button 10
times within 20 seconds.
• To deactivate service mode, turn on the ignition and enter the“Immobilizer PIN-code”.
Service mode indication
• Activated Service mode is indicated by: an icon in the mobile application, constant green LED
when the ignition is on, long sound signal of a Beeper at the moment you activate the mode.
• Deactivated Service mode is indicated by: no “Service mode”icon in the mobile application in
the mobile application, no constant green LED when the ignition is on, two long sound signal of a
Beeper at the moment you deactivate the mode.

35
34 USER MANUALSECURITY-SERVICE SYSTEM PANDORA CAMPER
EN
CONTROL THE SYSTEM IN CASE OF EMERGENCY
The system has emergency ways to deactivate security and anti-hijack functions (using the VALET
button and the“Secret PIN-code”) in case of loss or failure of control devices or in case of discharge of a
battery (when you cannot replace it or charge).
Before using emergency system control, check the system and vehicle control devices: check a
battery, turn on a device in accordance with its manual (if required).
If all devices are working, try to make a primary vehicle diagnosis: check the vehicle original control
device, vehicle battery charge level, gearbox selector position, check information on the dashboard.
!The sysTem can be conTrolled from aphone using dTmf commands:
0* – disarming.
998*xxxх – deacTivaTe auThorizaTion devices (immobilizer and anTi-hijack funcTions), where хххх is The “secreT pin-
code” wriTTen on The owner’spersonal card under The proTecTive layer.
1*– arming.
888* – acTivaTe auThorizaTion devices (immobilizer and anTi-hijack funcTions).
!read The procedure for enTering The pin-code before using emergency funcTions.
ENTERING THE PIN-CODE
The code must be entered only when the base unit is powered and the ignition is off. The PIN-code can
be entered using the external or located on the base unit VALET button. The digits input and correct
input is indicated by the external or located on the base unit LED indicator.
• Enter the first digit • Press the button the number of times equal to the first digit. Pauses between
presses should not exceed 1 second. Each pressing will be confirmed with an orange LED indicator flash.
Pause for more than 1 second, a red LED indicator flash and a short sound single of the Beeper confirm
the input of the first digit. Then you can enter the next digit.
• Enter the second digit • Press the button the number of times equal to the second digit. Pauses
between presses should not exceed 1 second. Each pressing will be confirmed with an orange LED
indicator flash. Pause for more than 1 second, a red LED indicator flash and a short sound single of the
Beeper confirm the input of the second digit. Then you can enter the next digit.
• Enter the third digit • Press the button the number of times equal to the third digit. Pauses
between presses should not exceed 1 second. Each pressing will be confirmed with an orange LED
indicator flash. Pause for more than 1 second, a red LED indicator flash and a short sound single of the
Beeper confirm the input of the third digit. Then you can enter the next digit.
• Enter the fourth digit • Press the button the number of times equal to the fourth digit. Pauses
between presses should not exceed 1 second. Each pressing will be confirmed with an orange LED
indicator flash. The correct input will be confirmed with the series of green and red flashes of the LED
indicator.
Emergency disarming
In case you cannot disarm the system as usual, use the VALET button and the ‘Secret PIN-code’written
on the Owner’s personal card (see the “General information”section):
• If your car is locked, unlock it by an original key. Not paying attention to the siren signals, make sure
that the ignition is off and enter the“Secret PIN-code”(see the procedure description above). If there
are no siren sounds or LED flashes, check the battery. It is not possible to enter the“Secret PIN-code”,
if there is no power supply.
• The system will be disarmed in case of correct PIN-code input. It will be confirmed with the series of
green and red flashes of the LED indicator, the series of sound signals of the Beeper, 4 beeps of the
Siren and 4 signals of the light signalization.
• The system will stay in previous state in case of incorrect input of the PIN-code. It will be indicated
with a long red flash of the LED indicator. New input can be attempted after 5 seconds.
• Emergency disarming is equivalent to a normal method of disarming. No additional actions are
required for further operation of the system.
Emergency control of the anti-theft functions
This section describes how to deactivate and activate “Code immobilizer” and anti-theft functions
(Immobilizer and Anti-Hi-jack), which use a radio tag, a remote control or a mobile phone as an owner
authorization device.
!ToTemporarily deacTivaTe The immobilizer or code immobilizer funcTion (pin-To-drive), Turn on The igniTion when The
sysTem is disarmed. enTer The “secreT code”from The owner’spersonal card using The valeT buTTon. The immobilizer
funcTions will be being deacTivaTed by The Time The igniTion is Turned off.
Emergency activation/deactivation Immobilizer/Code Immobilizer functions
Emergency control of the anti-theft functions is possible only when the system is disarmed, the
ignition is off, service mode is deactivated, a vehicle battery is charged. Enter the “Secret PIN-code” to
put the system in programming mode.
!you can also enTer programming mode using The “service pin-code” (defaulT value is 1-1-1-1).

37
36 USER MANUALSECURITY-SERVICE SYSTEM PANDORA CAMPER
EN
1. Emergency activation/deactivation the immobilizer function
After entering programming mode, press the VALET button 15 times. Pauses between presses should
not exceed 1 second. Each pressing will be confirmed with an orange LED indicator flash. The system
will confirm entering the 15th level with the red flashes of the LED and short signals of the Siren/Beeper.
• Deactivate immobilizer: The LED indicator will be green after entering the programming
level. The system will wait 10 seconds for entering the ‘Secret PIN-code’. Enter the ‘Secret
PIN-code’ that is written on the owner’s plastic card. If the PIN-code is not entered within
10 seconds or the input is incorrect, the siren will sound one signal, the LED will produce
the series of red and green flashes and the system will return to the programming menu.
The system will confirm deactivating with two sound signals of the siren, a long red LED flash and
the series of signals of the Beeper. After that, the system will return to the programming menu.
Turn on the ignition and then turn off to exit programming mode.The immobilizer will be deactivated.
• Activate immobilizer: The LED indicator will light red and the Beeper will sound a long
beep after entering the programming level. The system will wait for action. Press the
VALET button once activate the immobilizer function. The system will confirm enabling
with one short sound signal of the Siren/Beeper and a green LED light. Turn on the
ignition and then turn off to exit programming mode. The immobilizer will be activated.
2. Emergency activation/deactivation the code immobilizer function (pin-to-drive).
After entering programming mode, press the VALET button 13 times. Pauses between presses should
not exceed 1 second. Each pressing will be confirmed with an orange LED indicator flash. The system
will confirm entering the 13th level with the red flashes of the LED and short signals of the Siren/Beeper.
• Deactivate code immobilizer: The LED indicator will be green after entering the programming
level. The system will wait 10 seconds for entering the ‘Secret PIN-code’. Enter the ‘Secret
PIN-code’ that is written on the owner’s plastic card. If the PIN-code is not entered within
10 seconds or the input is incorrect, the siren will sound one signal, the LED will produce
the series of red and green flashes and the system will return to the programming menu.
The system will confirm deactivating with two sound signals of the siren, a long red LED flash and
the series of signals of the Beeper. After that, the system will return to the programming menu.
Turn on the ignition and then turn off to exit programming mode. The code immobilizer will be
deactivated.
• Activate code immobilizer: The LED indicator will light red and the Beeper will sound a long beep
after entering the programming level. The system will wait for action. Press the VALET button once
activate the immobilizer function. The system will confirm enabling with one short sound signal of
the Siren/Beeper and a green LED light. Turn on the ignition and then turn off to exit programming
mode. The code immobilizer will be activated.
Warranty obligations
Manufacturer guarantees correct operation of the service-security system if exploitation, installation,
storage and transportation conditions described in this manual were met.
The system should only be used according to installation scheme and user manuals.
The system is meant to be installed by the professional car electronics installers.The installer should
fill in installation certificate that is included in this manual.
Parts malfunctioning during warranty period on the fault of the manufacturer should be repaired
or replaced by the installation center of the manufacturer or by certified service center. List of certified
service centers can be found on pandorainfo.com
The user loses the right for warranty services in the following cases:
• when warranty period expires;
• if exploitation, installation, storage or transportation conditions were not met;
• if there is mechanical damage of the external parts of the system after it is sold.
This includes: fire damage, consequential damage in case of car accident, aggressive liquids and
water seeping damage, damage caused by improper use;
• if the damage was caused with incorrect settings and parameter adjustment;
• if system devices are replaced with any devices that are not recommended by the manufacturer;
• if manufacturer sealing is broken;
• if there is no properly filled warranty card and installation certificate.
Warranty period is 3 years since the moment of purchase, but no more than 3.5 (three and a half)
years since the moment of production. This warranty does not include batteries of the remotes, as they
have their own service lifetime.
Maintenances and repairs of the system with expired warranty period are carried out at the expense
of the user on a separate contract between the user and the installer/service center.
!werecommend ThaT you ask an insTaller To fill ouT The insTallaTion cerTificaTe and The warranTy card. These
documenTs may be required for conTacTing The cusTomer supporT.

39
38 USER MANUALSECURITY-SERVICE SYSTEM PANDORA CAMPER
EN
Installation certifcate
I, the undersigned_________________________________________________________
Position, name.
______________________________________________________________________________
professional installer, certify that installation of the service-security system, specified below, was carried
out by me in accordance with manuals and schemes provided by the manufacturer.
Car specifications:
Car model____________________________________________ Type _____________________
Id number (VIN)_________________________________________________________________
Registration number_____________________________________________________________
Security system specification:
Model Pandora Camper
Serial number______________________________
Service center name, full address and installer’s stamp
______________________________________________________________________________
______________________________________________________________________________
Signature_____________________/___________________________________/
Signator
Work accepted__________________/___________________________________/
Signator
Date «____»___________________20___year.
Acceptance certicate
Pandora Camper is in conformity with Electromagnetic Compatibility Directive EMC 2004/108/EC and
R&TTE Directive 1999/5/EC.
Serial number ______________________________ Date of production__________________________
Responsible person’s signature (stamp)
Packager_____________________________________________________________________________
Signature (personal stamp)
Warranty card
Model Pandora Camper
Serial number ________________________________________________________________________
Date of purchase «____» ______________________ 20____year
____________________________________________________________________________________
Seller’s (installer’s) stamp
Seller’s signature ______________________________________________________________________